spi: ti_qspi: Add delay for successful bulk erase.

[u-boot] / README

diff --git a/README b/README
index ff4926040b5dea46117edb7d34a8d798b1c44390..f39accfe5307ca7f1f94dbd8c6a8e13486f2604e 100644 (file)
--- a/README
+++ b/README
@@ -566,6 +566,8 @@ The following options need to be configured:
                CONFIG_ARM_ERRATA_742230
                CONFIG_ARM_ERRATA_743622
                CONFIG_ARM_ERRATA_751472
+               CONFIG_ARM_ERRATA_794072
+               CONFIG_ARM_ERRATA_761320
 
                If set, the workarounds for these ARM errata are applied early
                during U-Boot startup. Note that these options force the
@@ -1012,7 +1014,7 @@ The following options need to be configured:
                CONFIG_CMD_CDP          * Cisco Discover Protocol support
                CONFIG_CMD_MFSL         * Microblaze FSL support
                CONFIG_CMD_XIMG           Load part of Multi Image
-
+               CONFIG_CMD_UUID         * Generate random UUID or GUID string
 
                EXAMPLE: If you want all functions except of network
                support you can write:
@@ -1525,6 +1527,16 @@ The following options need to be configured:
                this to the maximum filesize (in bytes) for the buffer.
                Default is 4 MiB if undefined.
 
+               DFU_DEFAULT_POLL_TIMEOUT
+               Poll timeout [ms], is the timeout a device can send to the
+               host. The host must wait for this timeout before sending
+               a subsequent DFU_GET_STATUS request to the device.
+
+               DFU_MANIFEST_POLL_TIMEOUT
+               Poll timeout [ms], which the device sends to the host when
+               entering dfuMANIFEST state. Host waits this timeout, before
+               sending again an USB request to the device.
+
 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
                CONFIG_JFFS2_NAND_DEV
@@ -3242,6 +3254,10 @@ FIT uImage format:
                supports MMC, NAND and YMODEM loading of U-Boot and NAND
                NAND loading of the Linux Kernel.
 
+               CONFIG_SPL_OS_BOOT
+               Enable booting directly to an OS from SPL.
+               See also: doc/README.falcon
+
                CONFIG_SPL_DISPLAY_PRINT
                For ARM, enable an optional function to print more information
                about the running system.
@@ -3314,6 +3330,10 @@ FIT uImage format:
                Support for NAND boot using simple NAND drivers that
                expose the cmd_ctrl() interface.
 
+               CONFIG_SPL_MTD_SUPPORT
+               Support for the MTD subsystem within SPL.  Useful for
+               environment on NAND support within SPL.
+
                CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
                Set for the SPL on PPC mpc8xxx targets, support for
                drivers/ddr/fsl/libddr.o in SPL binary.
@@ -3470,6 +3490,9 @@ typically in board_init_f() and board_init_r().
 Configuration Settings:
 -----------------------
 
+- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+               Optionally it can be defined to support 64-bit memory commands.
+
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
                undefine this when you're short of memory.