MAKEALL: remove hard-coded MIPS boards

[u-boot] / README

diff --git a/README b/README
index 413d6828292dc0154c303711b34ad231f312f38e..f91e0442ad45d8cff50f2c1f8420ba95aad5ce40 100644 (file)
--- a/README
+++ b/README
@@ -132,6 +132,10 @@ Directory Hierarchy:
 ====================
 
 /arch                  Architecture specific files
+  /arc                 Files generic to ARC architecture
+    /cpu               CPU specific files
+      /arc700          Files specific to ARC 700 CPUs
+    /lib               Architecture specific library files
   /arm                 Files generic to ARM architecture
     /cpu               CPU specific files
       /arm720t         Files specific to ARM 720 CPUs
@@ -164,7 +168,7 @@ Directory Hierarchy:
   /mips                        Files generic to MIPS architecture
     /cpu               CPU specific files
       /mips32          Files specific to MIPS32 CPUs
-      /xburst          Files specific to Ingenic XBurst CPUs
+      /mips64          Files specific to MIPS64 CPUs
     /lib               Architecture specific library files
   /nds32               Files generic to NDS32 architecture
     /cpu               CPU specific files
@@ -492,6 +496,16 @@ The following options need to be configured:
                CONFIG_SYS_FSL_DDR_LE
                Defines the DDR controller register space as Little Endian
 
+               CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
+               Physical address from the view of DDR controllers. It is the
+               same as CONFIG_SYS_DDR_SDRAM_BASE for  all Power SoCs. But
+               it could be different for ARM SoCs.
+
+               CONFIG_SYS_FSL_DDR_INTLV_256B
+               DDR controller interleaving on 256-byte. This is a special
+               interleaving mode, handled by Dickens for Freescale layerscape
+               SoCs with ARM core.
+
 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
@@ -556,6 +570,8 @@ The following options need to be configured:
                CONFIG_ARM_ERRATA_742230
                CONFIG_ARM_ERRATA_743622
                CONFIG_ARM_ERRATA_751472
+               CONFIG_ARM_ERRATA_794072
+               CONFIG_ARM_ERRATA_761320
 
                If set, the workarounds for these ARM errata are applied early
                during U-Boot startup. Note that these options force the
@@ -900,6 +916,7 @@ The following options need to be configured:
                The default command configuration includes all commands
                except those marked below with a "*".
 
+               CONFIG_CMD_AES            AES 128 CBC encrypt/decrypt
                CONFIG_CMD_ASKENV       * ask for env variable
                CONFIG_CMD_BDI            bdinfo
                CONFIG_CMD_BEDBUG       * Include BedBug Debugger
@@ -1002,7 +1019,7 @@ The following options need to be configured:
                CONFIG_CMD_CDP          * Cisco Discover Protocol support
                CONFIG_CMD_MFSL         * Microblaze FSL support
                CONFIG_CMD_XIMG           Load part of Multi Image
-
+               CONFIG_CMD_UUID         * Generate random UUID or GUID string
 
                EXAMPLE: If you want all functions except of network
                support you can write:
@@ -1515,6 +1532,16 @@ The following options need to be configured:
                this to the maximum filesize (in bytes) for the buffer.
                Default is 4 MiB if undefined.
 
+               DFU_DEFAULT_POLL_TIMEOUT
+               Poll timeout [ms], is the timeout a device can send to the
+               host. The host must wait for this timeout before sending
+               a subsequent DFU_GET_STATUS request to the device.
+
+               DFU_MANIFEST_POLL_TIMEOUT
+               Poll timeout [ms], which the device sends to the host when
+               entering dfuMANIFEST state. Host waits this timeout, before
+               sending again an USB request to the device.
+
 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
                CONFIG_JFFS2_NAND_DEV
@@ -1731,7 +1758,7 @@ CBFS (Coreboot Filesystem) support
 
                If this option is set, then U-Boot will prevent the environment
                variable "splashimage" from being set to a problematic address
-               (see README.displaying-bmps and README.arm-unaligned-accesses).
+               (see README.displaying-bmps).
                This option is useful for targets where, due to alignment
                restrictions, an improperly aligned BMP image will cause a data
                abort. If you think you will not have problems with unaligned
@@ -3460,6 +3487,9 @@ typically in board_init_f() and board_init_r().
 Configuration Settings:
 -----------------------
 
+- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+               Optionally it can be defined to support 64-bit memory commands.
+
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
                undefine this when you're short of memory.
 
@@ -3732,12 +3762,6 @@ Configuration Settings:
        its config.mk file). If you find problems enabling this option on
        your board please report the problem and send patches!
 
-- CONFIG_SYS_SYM_OFFSETS
-       This is set by architectures that use offsets for link symbols
-       instead of absolute values. So bss_start is obtained using an
-       offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
-       directly. You should not need to touch this setting.
-
 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
        This is set by OMAP boards for the max time that reset should
        be asserted. See doc/README.omap-reset-time for details on how