#include <asm-offsets.h>
#include <config.h>
#include <common.h>
-#include <version.h>
-
-/*
- *************************************************************************
- *
- * Jump vector table as in table 3.1 in [1]
- *
- *************************************************************************
- */
-
-
-.globl _start
-_start:
- b reset
- b undefined_instruction
- b software_interrupt
- b prefetch_abort
- b data_abort
- b not_used
- b irq
- b fiq
-
-/*
- * Vector table, located at address 0x20.
- * This table allows the code running AFTER SPL, the U-Boot, to install it's
- * interrupt handlers here. The problem is that the U-Boot is loaded into RAM,
- * including it's interrupt vectoring table and the table at 0x0 is still the
- * SPLs. So if interrupt happens in U-Boot, the SPLs interrupt vectoring table
- * is still used.
- */
-_vt_reset:
- .word _reset
-_vt_undefined_instruction:
- .word _hang
-_vt_software_interrupt:
- .word _hang
-_vt_prefetch_abort:
- .word _hang
-_vt_data_abort:
- .word _hang
-_vt_not_used:
- .word _reset
-_vt_irq:
- .word _hang
-_vt_fiq:
- .word _hang
-
-reset:
- ldr pc, _vt_reset
-undefined_instruction:
- ldr pc, _vt_undefined_instruction
-software_interrupt:
- ldr pc, _vt_software_interrupt
-prefetch_abort:
- ldr pc, _vt_prefetch_abort
-data_abort:
- ldr pc, _vt_data_abort
-not_used:
- ldr pc, _vt_not_used
-irq:
- ldr pc, _vt_irq
-fiq:
- ldr pc, _vt_fiq
-
- .balignl 16,0xdeadbeef
/*
*************************************************************************
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#ifdef CONFIG_SPL_TEXT_BASE
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
-#ifdef CONFIG_USE_IRQ
-/* IRQ stack memory (calculated at run-time) */
-.globl IRQ_STACK_START
-IRQ_STACK_START:
- .word 0x0badc0de
-
-/* IRQ stack memory (calculated at run-time) */
-.globl FIQ_STACK_START
-FIQ_STACK_START:
- .word 0x0badc0de
-#endif
-
-/* IRQ stack memory (calculated at run-time) + 8 bytes */
-.globl IRQ_STACK_START_IN
-IRQ_STACK_START_IN:
- .word 0x0badc0de
-
-/*
- * the actual reset code
- */
+ .globl reset
+reset:
+ /*
+ * If the CPU is configured in "Wait JTAG connection mode", the stack
+ * pointer is not configured and is zero. This will cause crash when
+ * trying to push data onto stack right below here. Load the SP and make
+ * it point to the end of OCRAM if the SP is zero.
+ */
+ cmp sp, #0x00000000
+ ldreq sp, =CONFIG_SYS_INIT_SP_ADDR
-_reset:
/*
* Store all registers on old stack pointer, this will allow us later to
* return to the BootROM and let the BootROM load U-Boot into RAM.
mov r0, #0
bx lr
-
-_hang:
- ldr sp, _TEXT_BASE /* switch to abort stack */
-1:
- bl 1b /* hang and never return */