PLL_BUS, /* System Bus PLL*/
PLL_USBOTG, /* OTG USB PLL */
PLL_ENET, /* ENET PLL */
+ PLL_AUDIO, /* AUDIO PLL */
+ PLL_VIDEO, /* AUDIO PLL */
};
struct mxc_ccm_reg *imx_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+#if defined(CONFIG_MX6SX)
+ clrbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_QSPI2_ENFC_MASK);
+
+ clrsetbits_le32(&imx_ccm->cs2cdr,
+ MXC_CCM_CS2CDR_QSPI2_CLK_PODF_MASK |
+ MXC_CCM_CS2CDR_QSPI2_CLK_PRED_MASK |
+ MXC_CCM_CS2CDR_QSPI2_CLK_SEL_MASK,
+ cfg);
+
+ setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_QSPI2_ENFC_MASK);
+#else
clrbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
clrsetbits_le32(&imx_ccm->cs2cdr,
cfg);
setbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+#endif
setbits_le32(&imx_ccm->CCGR4,
MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
{
u32 mask, *addr;
- if (is_cpu_type(MXC_CPU_MX6UL)) {
+ if (is_mx6ul()) {
mask = MXC_CCM_CCGR3_ENET_MASK;
addr = &imx_ccm->CCGR3;
} else {
{
u32 mask;
- if (is_cpu_type(MXC_CPU_MX6UL))
+ if (is_mx6ul())
mask = MXC_CCM_CCGR5_UART_MASK;
else
mask = MXC_CCM_CCGR5_UART_MASK | MXC_CCM_CCGR5_UART_SERIAL_MASK;
reg &= ~mask;
__raw_writel(reg, &imx_ccm->CCGR2);
} else {
- if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) {
+ if (is_mx6sx() || is_mx6ul()) {
mask = MXC_CCM_CCGR6_I2C4_MASK;
addr = &imx_ccm->CCGR6;
} else {
}
static u32 decode_pll(enum pll_clocks pll, u32 infreq)
{
- u32 div;
+ u32 div, test_div, pll_num, pll_denom;
switch (pll) {
case PLL_SYS:
div &= BM_ANADIG_PLL_ENET_DIV_SELECT;
return 25000000 * (div + (div >> 1) + 1);
+ case PLL_AUDIO:
+ div = __raw_readl(&imx_ccm->analog_pll_audio);
+ if (!(div & BM_ANADIG_PLL_AUDIO_ENABLE))
+ return 0;
+ /* BM_ANADIG_PLL_AUDIO_BYPASS_CLK_SRC is ignored */
+ if (div & BM_ANADIG_PLL_AUDIO_BYPASS)
+ return MXC_HCLK;
+ pll_num = __raw_readl(&imx_ccm->analog_pll_audio_num);
+ pll_denom = __raw_readl(&imx_ccm->analog_pll_audio_denom);
+ test_div = (div & BM_ANADIG_PLL_AUDIO_TEST_DIV_SELECT) >>
+ BP_ANADIG_PLL_AUDIO_TEST_DIV_SELECT;
+ div &= BM_ANADIG_PLL_AUDIO_DIV_SELECT;
+ if (test_div == 3) {
+ debug("Error test_div\n");
+ return 0;
+ }
+ test_div = 1 << (2 - test_div);
+
+ return infreq * (div + pll_num / pll_denom) / test_div;
+ case PLL_VIDEO:
+ div = __raw_readl(&imx_ccm->analog_pll_video);
+ if (!(div & BM_ANADIG_PLL_VIDEO_ENABLE))
+ return 0;
+ /* BM_ANADIG_PLL_AUDIO_BYPASS_CLK_SRC is ignored */
+ if (div & BM_ANADIG_PLL_VIDEO_BYPASS)
+ return MXC_HCLK;
+ pll_num = __raw_readl(&imx_ccm->analog_pll_video_num);
+ pll_denom = __raw_readl(&imx_ccm->analog_pll_video_denom);
+ test_div = (div & BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT) >>
+ BP_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+ div &= BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+ if (test_div == 3) {
+ debug("Error test_div\n");
+ return 0;
+ }
+ test_div = 1 << (2 - test_div);
+
+ return infreq * (div + pll_num / pll_denom) / test_div;
default:
return 0;
}
switch (pll) {
case PLL_BUS:
- if (!is_cpu_type(MXC_CPU_MX6UL)) {
+ if (!is_mx6ul()) {
if (pfd_num == 3) {
- /* No PFD3 on PPL2 */
+ /* No PFD3 on PLL2 */
return 0;
}
}
u32 reg, perclk_podf;
reg = __raw_readl(&imx_ccm->cscmr1);
- if (is_cpu_type(MXC_CPU_MX6SL) || is_cpu_type(MXC_CPU_MX6SX) ||
- is_mx6dqp() || is_cpu_type(MXC_CPU_MX6UL)) {
+ if (is_mx6sl() || is_mx6sx() ||
+ is_mx6dqp() || is_mx6ul()) {
if (reg & MXC_CCM_CSCMR1_PER_CLK_SEL_MASK)
return MXC_HCLK; /* OSC 24Mhz */
}
u32 freq = decode_pll(PLL_USBOTG, MXC_HCLK) / 6; /* static divider */
reg = __raw_readl(&imx_ccm->cscdr1);
- if (is_cpu_type(MXC_CPU_MX6SL) || is_cpu_type(MXC_CPU_MX6SX) ||
- is_mx6dqp() || is_cpu_type(MXC_CPU_MX6UL)) {
+ if (is_mx6sl() || is_mx6sx() || is_mx6dqp() || is_mx6ul()) {
if (reg & MXC_CCM_CSCDR1_UART_CLK_SEL)
freq = MXC_HCLK;
}
cspi_podf = (reg & MXC_CCM_CSCDR2_ECSPI_CLK_PODF_MASK) >>
MXC_CCM_CSCDR2_ECSPI_CLK_PODF_OFFSET;
- if (is_mx6dqp() || is_cpu_type(MXC_CPU_MX6SL) ||
- is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) {
+ if (is_mx6dqp() || is_mx6sl() || is_mx6sx() || is_mx6ul()) {
if (reg & MXC_CCM_CSCDR2_ECSPI_CLK_SEL_MASK)
return MXC_HCLK / (cspi_podf + 1);
}
if (cbcdr & MXC_CCM_CBCDR_AXI_SEL) {
if (cbcdr & MXC_CCM_CBCDR_AXI_ALT_SEL)
- root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
- else
root_freq = mxc_get_pll_pfd(PLL_USBOTG, 1);
+ else
+ root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
} else
root_freq = get_periph_clk();
u32 cbcmr = __raw_readl(&imx_ccm->cbcmr);
u32 cbcdr = __raw_readl(&imx_ccm->cbcdr);
- u32 freq, podf, per2_clk2_podf;
+ u32 freq, podf, per2_clk2_podf, pmu_misc2_audio_div;
- if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL) ||
- is_cpu_type(MXC_CPU_MX6SL)) {
+ if (is_mx6sx() || is_mx6ul() || is_mx6sl()) {
podf = (cbcdr & MXC_CCM_CBCDR_MMDC_CH1_PODF_MASK) >>
MXC_CCM_CBCDR_MMDC_CH1_PODF_OFFSET;
if (cbcdr & MXC_CCM_CBCDR_PERIPH2_CLK_SEL) {
per2_clk2_podf = (cbcdr & MXC_CCM_CBCDR_PERIPH2_CLK2_PODF_MASK) >>
MXC_CCM_CBCDR_PERIPH2_CLK2_PODF_OFFSET;
- if (is_cpu_type(MXC_CPU_MX6SL)) {
+ if (is_mx6sl()) {
if (cbcmr & MXC_CCM_CBCMR_PERIPH2_CLK2_SEL)
freq = MXC_HCLK;
else
freq = mxc_get_pll_pfd(PLL_BUS, 0);
break;
case 3:
- /* static / 2 divider */
- freq = mxc_get_pll_pfd(PLL_BUS, 2) / 2;
+ pmu_misc2_audio_div = PMU_MISC2_AUDIO_DIV(__raw_readl(&imx_ccm->pmu_misc2));
+ switch (pmu_misc2_audio_div) {
+ case 0:
+ case 2:
+ pmu_misc2_audio_div = 1;
+ break;
+ case 1:
+ pmu_misc2_audio_div = 2;
+ break;
+ case 3:
+ pmu_misc2_audio_div = 4;
+ break;
+ }
+ freq = decode_pll(PLL_AUDIO, MXC_HCLK) /
+ pmu_misc2_audio_div;
break;
}
}
debug("mxs_set_lcdclk, freq = %dKHz\n", freq);
- if ((!is_cpu_type(MXC_CPU_MX6SX)) && !is_cpu_type(MXC_CPU_MX6UL)) {
+ if (!is_mx6sx() && !is_mx6ul()) {
debug("This chip not support lcd!\n");
return;
}
return;
}
- if (is_cpu_type(MXC_CPU_MX6SX)) {
+ if (is_mx6sx()) {
reg = readl(&imx_ccm->cscdr2);
/* Can't change clocks when clock not from pre-mux */
if ((reg & MXC_CCM_CSCDR2_LCDIF2_CLK_SEL_MASK) != 0)
}
temp = freq * max_pred * max_postd;
- if (temp > max) {
- puts("Please decrease freq, too large!\n");
- return;
- }
if (temp < min) {
/*
* Register: PLL_VIDEO
MXC_CCM_CBCMR_LCDIF1_PODF_MASK,
((postd - 1) <<
MXC_CCM_CBCMR_LCDIF1_PODF_OFFSET));
- } else if (is_cpu_type(MXC_CPU_MX6SX)) {
+ } else if (is_mx6sx()) {
/* Setting LCDIF2 for i.MX6SX */
if (enable_pll_video(pll_div, pll_num, pll_denom, post_div))
return;
u32 reg = 0;
u32 lcdif_clk_sel_mask, lcdif_ccgr3_mask;
- if (is_cpu_type(MXC_CPU_MX6SX)) {
- if ((base_addr == LCDIF1_BASE_ADDR) ||
- (base_addr == LCDIF2_BASE_ADDR)) {
+ if (is_mx6sx()) {
+ if ((base_addr != LCDIF1_BASE_ADDR) &&
+ (base_addr != LCDIF2_BASE_ADDR)) {
puts("Wrong LCD interface!\n");
return -EINVAL;
}
MXC_CCM_CCGR3_DISP_AXI_MASK) :
(MXC_CCM_CCGR3_LCDIF1_PIX_MASK |
MXC_CCM_CCGR3_DISP_AXI_MASK);
- } else if (is_cpu_type(MXC_CPU_MX6UL)) {
+ } else if (is_mx6ul()) {
if (base_addr != LCDIF1_BASE_ADDR) {
puts("Wrong LCD interface!\n");
return -EINVAL;
reg = readl(&imx_ccm->CCGR2);
reg |= MXC_CCM_CCGR2_LCD_MASK;
writel(reg, &imx_ccm->CCGR2);
+
+ return 0;
}
#endif
reg |= BF_ANADIG_PLL_ENET_DIV_SELECT(freq);
} else if (fec_id == 1) {
/* Only i.MX6SX/UL support ENET2 */
- if (!(is_cpu_type(MXC_CPU_MX6SX) ||
- is_cpu_type(MXC_CPU_MX6UL)))
+ if (!(is_mx6sx() || is_mx6ul()))
return -EINVAL;
reg &= ~BM_ANADIG_PLL_ENET2_DIV_SELECT;
reg |= BF_ANADIG_PLL_ENET2_DIV_SELECT(freq);
#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF 0xa
#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF 0xb
- if (is_cpu_type(MXC_CPU_MX6SX))
+ if (is_mx6sx())
lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF;
else
lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF;
printf("PLL_NET %8d MHz\n", freq / 1000000);
printf("\n");
+ printf("ARM %8d kHz\n", mxc_get_clock(MXC_ARM_CLK) / 1000);
printf("IPG %8d kHz\n", mxc_get_clock(MXC_IPG_CLK) / 1000);
printf("UART %8d kHz\n", mxc_get_clock(MXC_UART_CLK) / 1000);
#ifdef CONFIG_MXC_SPI
}
}
#endif
+
+#if defined(CONFIG_MX6Q) || defined(CONFIG_MX6D) || defined(CONFIG_MX6DL) || \
+ defined(CONFIG_MX6S)
+static void disable_ldb_di_clock_sources(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+
+ /* Make sure PFDs are disabled at boot. */
+ reg = readl(&mxc_ccm->analog_pfd_528);
+ /* Cannot disable pll2_pfd2_396M, as it is the MMDC clock in iMX6DL */
+ if (is_mx6sdl())
+ reg |= 0x80008080;
+ else
+ reg |= 0x80808080;
+ writel(reg, &mxc_ccm->analog_pfd_528);
+
+ /* Disable PLL3 PFDs */
+ reg = readl(&mxc_ccm->analog_pfd_480);
+ reg |= 0x80808080;
+ writel(reg, &mxc_ccm->analog_pfd_480);
+
+ /* Disable PLL5 */
+ reg = readl(&mxc_ccm->analog_pll_video);
+ reg &= ~(1 << 13);
+ writel(reg, &mxc_ccm->analog_pll_video);
+}
+
+static void enable_ldb_di_clock_sources(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+
+ reg = readl(&mxc_ccm->analog_pfd_528);
+ if (is_mx6sdl())
+ reg &= ~(0x80008080);
+ else
+ reg &= ~(0x80808080);
+ writel(reg, &mxc_ccm->analog_pfd_528);
+
+ reg = readl(&mxc_ccm->analog_pfd_480);
+ reg &= ~(0x80808080);
+ writel(reg, &mxc_ccm->analog_pfd_480);
+}
+
+/*
+ * Try call this function as early in the boot process as possible since the
+ * function temporarily disables PLL2 PFD's, PLL3 PFD's and PLL5.
+ */
+void select_ldb_di_clock_source(enum ldb_di_clock clk)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+
+ /*
+ * Need to follow a strict procedure when changing the LDB
+ * clock, else we can introduce a glitch. Things to keep in
+ * mind:
+ * 1. The current and new parent clocks must be disabled.
+ * 2. The default clock for ldb_dio_clk is mmdc_ch1 which has
+ * no CG bit.
+ * 3. In the RTL implementation of the LDB_DI_CLK_SEL mux
+ * the top four options are in one mux and the PLL3 option along
+ * with another option is in the second mux. There is third mux
+ * used to decide between the first and second mux.
+ * The code below switches the parent to the bottom mux first
+ * and then manipulates the top mux. This ensures that no glitch
+ * will enter the divider.
+ *
+ * Need to disable MMDC_CH1 clock manually as there is no CG bit
+ * for this clock. The only way to disable this clock is to move
+ * it to pll3_sw_clk and then to disable pll3_sw_clk
+ * Make sure periph2_clk2_sel is set to pll3_sw_clk
+ */
+
+ /* Disable all ldb_di clock parents */
+ disable_ldb_di_clock_sources();
+
+ /* Set MMDC_CH1 mask bit */
+ reg = readl(&mxc_ccm->ccdr);
+ reg |= MXC_CCM_CCDR_MMDC_CH1_HS_MASK;
+ writel(reg, &mxc_ccm->ccdr);
+
+ /* Set periph2_clk2_sel to be sourced from PLL3_sw_clk */
+ reg = readl(&mxc_ccm->cbcmr);
+ reg &= ~MXC_CCM_CBCMR_PERIPH2_CLK2_SEL;
+ writel(reg, &mxc_ccm->cbcmr);
+
+ /*
+ * Set the periph2_clk_sel to the top mux so that
+ * mmdc_ch1 is from pll3_sw_clk.
+ */
+ reg = readl(&mxc_ccm->cbcdr);
+ reg |= MXC_CCM_CBCDR_PERIPH2_CLK_SEL;
+ writel(reg, &mxc_ccm->cbcdr);
+
+ /* Wait for the clock switch */
+ while (readl(&mxc_ccm->cdhipr))
+ ;
+ /* Disable pll3_sw_clk by selecting bypass clock source */
+ reg = readl(&mxc_ccm->ccsr);
+ reg |= MXC_CCM_CCSR_PLL3_SW_CLK_SEL;
+ writel(reg, &mxc_ccm->ccsr);
+
+ /* Set the ldb_di0_clk and ldb_di1_clk to 111b */
+ reg = readl(&mxc_ccm->cs2cdr);
+ reg |= ((7 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET)
+ | (7 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET));
+ writel(reg, &mxc_ccm->cs2cdr);
+
+ /* Set the ldb_di0_clk and ldb_di1_clk to 100b */
+ reg = readl(&mxc_ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK);
+ reg |= ((4 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET)
+ | (4 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET));
+ writel(reg, &mxc_ccm->cs2cdr);
+
+ /* Set the ldb_di0_clk and ldb_di1_clk to desired source */
+ reg = readl(&mxc_ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK);
+ reg |= ((clk << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET)
+ | (clk << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET));
+ writel(reg, &mxc_ccm->cs2cdr);
+
+ /* Unbypass pll3_sw_clk */
+ reg = readl(&mxc_ccm->ccsr);
+ reg &= ~MXC_CCM_CCSR_PLL3_SW_CLK_SEL;
+ writel(reg, &mxc_ccm->ccsr);
+
+ /*
+ * Set the periph2_clk_sel back to the bottom mux so that
+ * mmdc_ch1 is from its original parent.
+ */
+ reg = readl(&mxc_ccm->cbcdr);
+ reg &= ~MXC_CCM_CBCDR_PERIPH2_CLK_SEL;
+ writel(reg, &mxc_ccm->cbcdr);
+
+ /* Wait for the clock switch */
+ while (readl(&mxc_ccm->cdhipr))
+ ;
+ /* Clear MMDC_CH1 mask bit */
+ reg = readl(&mxc_ccm->ccdr);
+ reg &= ~MXC_CCM_CCDR_MMDC_CH1_HS_MASK;
+ writel(reg, &mxc_ccm->ccdr);
+
+ enable_ldb_di_clock_sources();
+}
+#endif
+
/***************************************************/
U_BOOT_CMD(
projects / u-boot / blobdiff