config ARCH_LS1012A
- bool "Freescale Layerscape LS1012A SoC"
+ bool
+ select ARMV8_SET_SMPEN
+ select FSL_LSCH2
+ select SYS_FSL_DDR_BE
select SYS_FSL_MMDC
select SYS_FSL_ERRATUM_A010315
+ select ARCH_EARLY_INIT_R
+ select BOARD_EARLY_INIT_F
config ARCH_LS1043A
- bool "Freescale Layerscape LS1043A SoC"
+ bool
+ select ARMV8_SET_SMPEN
+ select FSL_LSCH2
+ select SYS_FSL_DDR
+ select SYS_FSL_DDR_BE
+ select SYS_FSL_DDR_VER_50
+ select SYS_FSL_ERRATUM_A008850
+ select SYS_FSL_ERRATUM_A009660
+ select SYS_FSL_ERRATUM_A009663
+ select SYS_FSL_ERRATUM_A009929
+ select SYS_FSL_ERRATUM_A009942
select SYS_FSL_ERRATUM_A010315
select SYS_FSL_ERRATUM_A010539
+ select SYS_FSL_HAS_DDR3
+ select SYS_FSL_HAS_DDR4
+ select ARCH_EARLY_INIT_R
+ select BOARD_EARLY_INIT_F
config ARCH_LS1046A
- bool "Freescale Layerscape LS1046A SoC"
+ bool
+ select ARMV8_SET_SMPEN
+ select FSL_LSCH2
+ select SYS_FSL_DDR
+ select SYS_FSL_DDR_BE
+ select SYS_FSL_DDR_VER_50
+ select SYS_FSL_ERRATUM_A008336
+ select SYS_FSL_ERRATUM_A008511
+ select SYS_FSL_ERRATUM_A008850
+ select SYS_FSL_ERRATUM_A009801
+ select SYS_FSL_ERRATUM_A009803
+ select SYS_FSL_ERRATUM_A009942
+ select SYS_FSL_ERRATUM_A010165
select SYS_FSL_ERRATUM_A010539
+ select SYS_FSL_HAS_DDR4
+ select SYS_FSL_SRDS_2
+ select ARCH_EARLY_INIT_R
+ select BOARD_EARLY_INIT_F
-config SYS_FSL_MMDC
- bool "Freescale Multi Mode DDR Controller"
+config ARCH_LS2080A
+ bool
+ select ARMV8_SET_SMPEN
+ select ARM_ERRATA_826974
+ select ARM_ERRATA_828024
+ select ARM_ERRATA_829520
+ select ARM_ERRATA_833471
+ select FSL_LSCH3
+ select SYS_FSL_DDR
+ select SYS_FSL_DDR_LE
+ select SYS_FSL_DDR_VER_50
+ select SYS_FSL_HAS_DP_DDR
+ select SYS_FSL_HAS_SEC
+ select SYS_FSL_HAS_DDR4
+ select SYS_FSL_SEC_COMPAT_5
+ select SYS_FSL_SEC_LE
+ select SYS_FSL_SRDS_2
+ select SYS_FSL_ERRATUM_A008336
+ select SYS_FSL_ERRATUM_A008511
+ select SYS_FSL_ERRATUM_A008514
+ select SYS_FSL_ERRATUM_A008585
+ select SYS_FSL_ERRATUM_A009635
+ select SYS_FSL_ERRATUM_A009663
+ select SYS_FSL_ERRATUM_A009801
+ select SYS_FSL_ERRATUM_A009803
+ select SYS_FSL_ERRATUM_A009942
+ select SYS_FSL_ERRATUM_A010165
+ select SYS_FSL_ERRATUM_A009203
+ select ARCH_EARLY_INIT_R
+ select BOARD_EARLY_INIT_F
+
+config FSL_LSCH2
+ bool
+ select SYS_FSL_HAS_SEC
+ select SYS_FSL_SEC_COMPAT_5
+ select SYS_FSL_SEC_BE
+ select SYS_FSL_SRDS_1
+ select SYS_HAS_SERDES
+
+config FSL_LSCH3
+ bool
+ select SYS_FSL_SRDS_1
+ select SYS_HAS_SERDES
+
+config FSL_MC_ENET
+ bool "Management Complex network"
+ depends on ARCH_LS2080A
+ default y
+ select RESV_RAM
+ help
+ Enable Management Complex (MC) network
+
+menu "Layerscape architecture"
+ depends on FSL_LSCH2 || FSL_LSCH3
+
+config FSL_PCIE_COMPAT
+ string "PCIe compatible of Kernel DT"
+ depends on PCIE_LAYERSCAPE
+ default "fsl,ls1012a-pcie" if ARCH_LS1012A
+ default "fsl,ls1043a-pcie" if ARCH_LS1043A
+ default "fsl,ls1046a-pcie" if ARCH_LS1046A
+ default "fsl,ls2080a-pcie" if ARCH_LS2080A
+ help
+ This compatible is used to find pci controller node in Kernel DT
+ to complete fixup.
+
+config HAS_FEATURE_GIC64K_ALIGN
+ bool
+ default y if ARCH_LS1043A
+
+config HAS_FEATURE_ENHANCED_MSI
+ bool
+ default y if ARCH_LS1043A
+
+menu "Layerscape PPA"
+config FSL_LS_PPA
+ bool "FSL Layerscape PPA firmware support"
+ depends on !ARMV8_PSCI
+ select ARMV8_SEC_FIRMWARE_SUPPORT
+ select SEC_FIRMWARE_ARMV8_PSCI
+ select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT if FSL_LSCH2
+ help
+ The FSL Primary Protected Application (PPA) is a software component
+ which is loaded during boot stage, and then remains resident in RAM
+ and runs in the TrustZone after boot.
+ Say y to enable it.
+choice
+ prompt "FSL Layerscape PPA firmware loading-media select"
+ depends on FSL_LS_PPA
+ default SYS_LS_PPA_FW_IN_MMC if SD_BOOT
+ default SYS_LS_PPA_FW_IN_NAND if NAND_BOOT
+ default SYS_LS_PPA_FW_IN_XIP
+
+config SYS_LS_PPA_FW_IN_XIP
+ bool "XIP"
+ help
+ Say Y here if the PPA firmware locate at XIP flash, such
+ as NOR or QSPI flash.
+
+config SYS_LS_PPA_FW_IN_MMC
+ bool "eMMC or SD Card"
+ help
+ Say Y here if the PPA firmware locate at eMMC/SD card.
+
+config SYS_LS_PPA_FW_IN_NAND
+ bool "NAND"
+ help
+ Say Y here if the PPA firmware locate at NAND flash.
+
+endchoice
+
+config SYS_LS_PPA_FW_ADDR
+ hex "Address of PPA firmware loading from"
+ depends on FSL_LS_PPA
+ default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
+ default 0x580a00000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS2080A
+ default 0x60500000 if SYS_LS_PPA_FW_IN_XIP
+ default 0x500000 if SYS_LS_PPA_FW_IN_MMC
+ default 0x500000 if SYS_LS_PPA_FW_IN_NAND
+
+ help
+ If the PPA firmware locate at XIP flash, such as NOR or
+ QSPI flash, this address is a directly memory-mapped.
+ If it is in a serial accessed flash, such as NAND and SD
+ card, it is a byte offset.
+
+config SYS_LS_PPA_ESBC_ADDR
+ hex "hdr address of PPA firmware loading from"
+ depends on FSL_LS_PPA && CHAIN_OF_TRUST
+ default 0x600c0000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1043A
+ default 0x40740000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1046A
+ default 0x40480000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1012A
+ default 0x580c40000 if SYS_LS_PPA_FW_IN_XIP && FSL_LSCH3
+ help
+ If the PPA header firmware locate at XIP flash, such as NOR or
+ QSPI flash, this address is a directly memory-mapped.
+ If it is in a serial accessed flash, such as NAND and SD
+ card, it is a byte offset.
+
+endmenu
config SYS_FSL_ERRATUM_A010315
bool "Workaround for PCIe erratum A010315"
config SYS_FSL_ERRATUM_A010539
bool "Workaround for PIN MUX erratum A010539"
+
+config MAX_CPUS
+ int "Maximum number of CPUs permitted for Layerscape"
+ default 4 if ARCH_LS1043A
+ default 4 if ARCH_LS1046A
+ default 16 if ARCH_LS2080A
+ default 1
+ help
+ Set this number to the maximum number of possible CPUs in the SoC.
+ SoCs may have multiple clusters with each cluster may have multiple
+ ports. If some ports are reserved but higher ports are used for
+ cores, count the reserved ports. This will allocate enough memory
+ in spin table to properly handle all cores.
+
+config SECURE_BOOT
+ bool "Secure Boot"
+ help
+ Enable Freescale Secure Boot feature
+
+config QSPI_AHB_INIT
+ bool "Init the QSPI AHB bus"
+ help
+ The default setting for QSPI AHB bus just support 3bytes addressing.
+ But some QSPI flash size up to 64MBytes, so initialize the QSPI AHB
+ bus for those flashes to support the full QSPI flash size.
+
+config SYS_FSL_IFC_BANK_COUNT
+ int "Maximum banks of Integrated flash controller"
+ depends on ARCH_LS1043A || ARCH_LS1046A || ARCH_LS2080A
+ default 4 if ARCH_LS1043A
+ default 4 if ARCH_LS1046A
+ default 8 if ARCH_LS2080A
+
+config SYS_FSL_HAS_DP_DDR
+ bool
+
+config SYS_FSL_SRDS_1
+ bool
+
+config SYS_FSL_SRDS_2
+ bool
+
+config SYS_HAS_SERDES
+ bool
+
+endmenu
+
+menu "Layerscape clock tree configuration"
+ depends on FSL_LSCH2 || FSL_LSCH3
+
+config SYS_FSL_CLK
+ bool "Enable clock tree initialization"
+ default y
+
+config CLUSTER_CLK_FREQ
+ int "Reference clock of core cluster"
+ depends on ARCH_LS1012A
+ default 100000000
+ help
+ This number is the reference clock frequency of core PLL.
+ For most platforms, the core PLL and Platform PLL have the same
+ reference clock, but for some platforms, LS1012A for instance,
+ they are provided sepatately.
+
+config SYS_FSL_PCLK_DIV
+ int "Platform clock divider"
+ default 1 if ARCH_LS1043A
+ default 1 if ARCH_LS1046A
+ default 2
+ help
+ This is the divider that is used to derive Platform clock from
+ Platform PLL, in another word:
+ Platform_clk = Platform_PLL_freq / this_divider
+
+config SYS_FSL_DSPI_CLK_DIV
+ int "DSPI clock divider"
+ default 1 if ARCH_LS1043A
+ default 2
+ help
+ This is the divider that is used to derive DSPI clock from Platform
+ PLL, in another word DSPI_clk = Platform_PLL_freq / this_divider.
+
+config SYS_FSL_DUART_CLK_DIV
+ int "DUART clock divider"
+ default 1 if ARCH_LS1043A
+ default 2
+ help
+ This is the divider that is used to derive DUART clock from Platform
+ clock, in another word DUART_clk = Platform_clk / this_divider.
+
+config SYS_FSL_I2C_CLK_DIV
+ int "I2C clock divider"
+ default 1 if ARCH_LS1043A
+ default 2
+ help
+ This is the divider that is used to derive I2C clock from Platform
+ clock, in another word I2C_clk = Platform_clk / this_divider.
+
+config SYS_FSL_IFC_CLK_DIV
+ int "IFC clock divider"
+ default 1 if ARCH_LS1043A
+ default 2
+ help
+ This is the divider that is used to derive IFC clock from Platform
+ clock, in another word IFC_clk = Platform_clk / this_divider.
+
+config SYS_FSL_LPUART_CLK_DIV
+ int "LPUART clock divider"
+ default 1 if ARCH_LS1043A
+ default 2
+ help
+ This is the divider that is used to derive LPUART clock from Platform
+ clock, in another word LPUART_clk = Platform_clk / this_divider.
+
+config SYS_FSL_SDHC_CLK_DIV
+ int "SDHC clock divider"
+ default 1 if ARCH_LS1043A
+ default 1 if ARCH_LS1012A
+ default 2
+ help
+ This is the divider that is used to derive SDHC clock from Platform
+ clock, in another word SDHC_clk = Platform_clk / this_divider.
+endmenu
+
+config RESV_RAM
+ bool
+ help
+ Reserve memory from the top, tracked by gd->arch.resv_ram. This
+ reserved RAM can be used by special driver that resides in memory
+ after U-Boot exits. It's up to implementation to allocate and allow
+ access to this reserved memory. For example, the reserved RAM can
+ be at the high end of physical memory. The reserve RAM may be
+ excluded from memory bank(s) passed to OS, or marked as reserved.
+
+config SYS_FSL_ERRATUM_A008336
+ bool
+
+config SYS_FSL_ERRATUM_A008514
+ bool
+
+config SYS_FSL_ERRATUM_A008585
+ bool
+
+config SYS_FSL_ERRATUM_A008850
+ bool
+
+config SYS_FSL_ERRATUM_A009203
+ bool
+
+config SYS_FSL_ERRATUM_A009635
+ bool
+
+config SYS_FSL_ERRATUM_A009660
+ bool
+
+config SYS_FSL_ERRATUM_A009929
+ bool
+
+config SYS_MC_RSV_MEM_ALIGN
+ hex "Management Complex reserved memory alignment"
+ depends on RESV_RAM
+ default 0x20000000
+ help
+ Reserved memory needs to be aligned for MC to use. Default value
+ is 512MB.
projects / u-boot / blobdiff