--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU100 revC
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Nathalie Chan King Choy
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+ model = "ZynqMP ZCU100 RevC";
+ compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp";
+
+ aliases {
+ gpio0 = &gpio;
+ i2c0 = &i2c1;
+ rtc0 = &rtc;
+ serial0 = &uart1;
+ serial1 = &uart0;
+ serial2 = &dcc;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw4 {
+ label = "sw4";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
+ <&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>,
+ <&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>,
+ <&xilinx_ams 9>, <&xilinx_ams 10>,
+ <&xilinx_ams 11>, <&xilinx_ams 12>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ ds2 {
+ label = "ds2";
+ gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds3 {
+ label = "ds3";
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx"; /* WLAN tx */
+ default-state = "off";
+ };
+
+ ds4 {
+ label = "ds4";
+ gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0rx"; /* WLAN rx */
+ default-state = "off";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ };
+
+ vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
+ label = "vbus_det";
+ gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ ltc2954: ltc2954 { /* U7 */
+ compatible = "lltc,ltc2954", "lltc,ltc2952";
+ trigger-gpios = <&gpio 26 GPIO_ACTIVE_LOW>; /* INT line - input */
+ /* If there is HW watchdog on mezzanine this signal should be connected there */
+ watchdog-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; /* MIO on PAD */
+ kill-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; /* KILL signal - output */
+ };
+
+ wmmcsdio_fixed: fixedregulator-mmcsdio {
+ compatible = "regulator-fixed";
+ regulator-name = "wmmcsdio_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ sdio_pwrseq: sdio_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+ gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL",
+ "I2C1_SDA", "SPI1_SCLK", "WLAN_EN", "BT_EN", "SPI1_CS",
+ "SPI1_MISO", "SPI1_MOSI", "I2C_MUX_RESET", "SD0_DAT0", "SD0_DAT1",
+ "SD0_DAT2", "SD0_DAT3", "PS_LED3", "PS_LED2", "PS_LED1",
+ "PS_LED0", "SD0_CMD", "SD0_CLK", "GPIO_PB", "SD0_DETECT",
+ "VBUS_DET", "POWER_INT", "DP_AUX", "DP_HPD", "DP_OE",
+ "DP_AUX_IN", "INA226_ALERT", "PS_FP_PWR_EN", "PL_PWR_EN", "POWER_KILL",
+ "", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C",
+ "GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E",
+ "GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3",
+ "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2",
+ "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3",
+ "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK",
+ "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1",
+ "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6",
+ "USB_DATA7", "WLAN_IRQ", "PMIC_IRQ", /* MIO end and EMIO start */
+ "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ i2c-mux@75 { /* u11 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2csw_0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ label = "LS-I2C0";
+ };
+ i2csw_1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ label = "LS-I2C1";
+ };
+ i2csw_2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ label = "HS-I2C2";
+ };
+ i2csw_3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ label = "HS-I2C3";
+ };
+ i2csw_4: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ pmic: pmic@5e { /* Custom TI PMIC u33 */
+ compatible = "ti,tps65086";
+ reg = <0x5e>;
+ interrupt-parent = <&gpio>;
+ interrupts = <77 GPIO_ACTIVE_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+ i2csw_5: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* PS_PMBUS */
+ ina226@40 { /* u35 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <10000>;
+ /* MIO31 is alert which should be routed to PMUFW */
+ };
+ };
+ i2csw_6: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /*
+ * Not Connected
+ */
+ };
+ i2csw_7: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /*
+ * usb5744 (DNP) - U5
+ * 100kHz - this is default freq for us
+ */
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+/* SD0 only supports 3.3V, no level shifter */
+&sdhci0 {
+ status = "okay";
+ no-1-8-v;
+ broken-cd; /* CD has to be enabled by default */
+ disable-wp;
+ xlnx,mio_bank = <0>;
+};
+
+&sdhci1 {
+ status = "okay";
+ bus-width = <0x4>;
+ xlnx,mio_bank = <0>;
+ non-removable;
+ disable-wp;
+ cap-power-off-card;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ vqmmc-supply = <&wmmcsdio_fixed>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wifi@2 {
+ compatible = "ti,wl1831";
+ reg = <2>;
+ interrupt-parent = <&gpio>;
+ interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */
+ };
+};
+
+&serdes {
+ status = "okay";
+};
+
+&spi0 { /* Low Speed connector */
+ status = "okay";
+ label = "LS-SPI0";
+};
+
+&spi1 { /* High Speed connector */
+ status = "okay";
+ label = "HS-SPI1";
+};
+
+&uart0 {
+ status = "okay";
+ bluetooth {
+ compatible = "ti,wl1831-st";
+ enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+ };
+
+};
+
+&uart1 {
+ status = "okay";
+
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "peripheral";
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 0 26000000>;
+ maximum-speed = "super-speed";
+};
+
+/* ULPI SMSC USB3320 */
+&usb1 {
+ status = "okay";
+};
+
+&dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+ phy-names = "usb3-phy";
+ phys = <&lane3 PHY_TYPE_USB3 1 0 26000000>;
+ maximum-speed = "super-speed";
+};
+
+&watchdog0 {
+ status = "okay";
+};
+
+&xilinx_ams {
+ status = "okay";
+};
+
+&ams_ps {
+ status = "okay";
+};
projects / u-boot / blobdiff