u32 apb0_gate; /* 0x68 apb0 module clock gating */
u32 apb1_gate; /* 0x6c apb1 module clock gating */
u8 res4[0x10];
- u32 nand_sclk_cfg; /* 0x80 nand sub clock control */
+ u32 nand0_clk_cfg; /* 0x80 nand sub clock control */
u32 ms_sclk_cfg; /* 0x84 memory stick sub clock control */
u32 sd0_clk_cfg; /* 0x88 sd0 clock control */
u32 sd1_clk_cfg; /* 0x8c sd1 clock control */
#define PLL1_CFG_DEFAULT 0xa1005000
+#if defined CONFIG_OLD_SUNXI_KERNEL_COMPAT && defined CONFIG_MACH_SUN5I
+/*
+ * Older linux-sunxi-3.4 kernels override our PLL6 setting with 300 MHz,
+ * halving the mbus frequency, so set it to 300 MHz ourselves and base the
+ * mbus divider on that.
+ */
+#define PLL6_CFG_DEFAULT 0xa1009900
+#else
#define PLL6_CFG_DEFAULT 0xa1009911
+#endif
/* nand clock */
#define NAND_CLK_SRC_OSC24 0
#define AHB_GATE_OFFSET_ACE 16
#define AHB_GATE_OFFSET_DLL 15
#define AHB_GATE_OFFSET_SDRAM 14
-#define AHB_GATE_OFFSET_NAND 13
+#define AHB_GATE_OFFSET_NAND0 13
#define AHB_GATE_OFFSET_MS 12
#define AHB_GATE_OFFSET_MMC3 11
#define AHB_GATE_OFFSET_MMC2 10
#define AHB_GATE_OFFSET_USB_EHCI1 3
#define AHB_GATE_OFFSET_USB_OHCI0 2
#define AHB_GATE_OFFSET_USB_EHCI0 1
-#define AHB_GATE_OFFSET_USB 0
+#define AHB_GATE_OFFSET_USB0 0
/* ahb clock gate bit offset (second register) */
#define AHB_GATE_OFFSET_GMAC 17
+#define AHB_GATE_OFFSET_DE_FE0 14
#define AHB_GATE_OFFSET_DE_BE0 12
#define AHB_GATE_OFFSET_HDMI 11
#define AHB_GATE_OFFSET_LCD1 5
#define CCM_AHB_GATE_DLL (0x1 << 15)
#define CCM_AHB_GATE_ACE (0x1 << 16)
+#define CCM_PLL3_CTRL_M_SHIFT 0
+#define CCM_PLL3_CTRL_M_MASK (0x7f << CCM_PLL3_CTRL_M_SHIFT)
#define CCM_PLL3_CTRL_M(n) (((n) & 0x7f) << 0)
#define CCM_PLL3_CTRL_INTEGER_MODE (0x1 << 15)
#define CCM_PLL3_CTRL_EN (0x1 << 31)
#define CCM_MBUS_CTRL_CLK_SRC_PLL5 0x2
#define CCM_MBUS_CTRL_GATE (0x1 << 31)
+#define CCM_NAND_CTRL_ENABLE (0x1 << 31)
+
#define CCM_MMC_CTRL_M(x) ((x) - 1)
#define CCM_MMC_CTRL_OCLK_DLY(x) ((x) << 8)
#define CCM_MMC_CTRL_N(x) ((x) << 16)
#define CCM_MMC_CTRL_PLL5 (0x2 << 24)
#define CCM_MMC_CTRL_ENABLE (0x1 << 31)
+#define CCM_DRAM_GATE_OFFSET_DE_FE1 24 /* Note the order of FE1 and */
+#define CCM_DRAM_GATE_OFFSET_DE_FE0 25 /* FE0 is swapped ! */
#define CCM_DRAM_GATE_OFFSET_DE_BE0 26
+#define CCM_DRAM_GATE_OFFSET_DE_BE1 27
#define CCM_LCD_CH0_CTRL_PLL3 (0 << 24)
#define CCM_LCD_CH0_CTRL_PLL7 (1 << 24)
#define CCM_LCD_CH0_CTRL_PLL3_2X (2 << 24)
#define CCM_LCD_CH0_CTRL_PLL7_2X (3 << 24)
+#define CCM_LCD_CH0_CTRL_MIPI_PLL 0 /* No mipi pll on sun4i/5i/7i */
+#ifdef CONFIG_MACH_SUN5I
+#define CCM_LCD_CH0_CTRL_TVE_RST (0x1 << 29)
+#else
+#define CCM_LCD_CH0_CTRL_TVE_RST 0 /* No separate tve-rst on sun4i/7i */
+#endif
#define CCM_LCD_CH0_CTRL_RST (0x1 << 30)
#define CCM_LCD_CH0_CTRL_GATE (0x1 << 31)
#define CCM_LCD_CH1_CTRL_M(n) ((((n) - 1) & 0xf) << 0)
-/* We leave bit 11 set to 0, so sclk1 == sclk2 */
+#define CCM_LCD_CH1_CTRL_HALF_SCLK1 (1 << 11)
#define CCM_LCD_CH1_CTRL_PLL3 (0 << 24)
#define CCM_LCD_CH1_CTRL_PLL7 (1 << 24)
#define CCM_LCD_CH1_CTRL_PLL3_2X (2 << 24)
#define CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII 0x2
#define CCM_GMAC_CTRL_GPIT_MII (0x0 << 2)
#define CCM_GMAC_CTRL_GPIT_RGMII (0x1 << 2)
+#define CCM_GMAC_CTRL_RX_CLK_DELAY(x) ((x) << 5)
+#define CCM_GMAC_CTRL_TX_CLK_DELAY(x) ((x) << 10)
+#define CCM_USB_CTRL_PHY0_RST (0x1 << 0)
#define CCM_USB_CTRL_PHY1_RST (0x1 << 1)
#define CCM_USB_CTRL_PHY2_RST (0x1 << 2)
+#define CCM_USB_CTRL_OHCI0_CLK (0x1 << 6)
+#define CCM_USB_CTRL_OHCI1_CLK (0x1 << 7)
#define CCM_USB_CTRL_PHYGATE (0x1 << 8)
-/* These 2 are sun6i only, define them as 0 on sun4i */
+/* These 3 are sun6i only, define them as 0 on sun4i */
+#define CCM_USB_CTRL_PHY0_CLK 0
#define CCM_USB_CTRL_PHY1_CLK 0
#define CCM_USB_CTRL_PHY2_CLK 0
#define CCM_DE_CTRL_RST (1 << 30)
#define CCM_DE_CTRL_GATE (1 << 31)
+#ifndef __ASSEMBLY__
+void clock_set_pll1(unsigned int hz);
+void clock_set_pll3(unsigned int hz);
+unsigned int clock_get_pll3(void);
+unsigned int clock_get_pll5p(void);
+unsigned int clock_get_pll6(void);
+#endif
+
#endif /* _SUNXI_CLOCK_SUN4I_H */