rockchip: rk3288: move evb board to rockchip folder

[u-boot] / arch / arm / mach-rockchip / rk3288-board-spl.c

diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c
index 8199cad3facc20251984605ca4005e91c0b8e093..1b74173430842e7b0060a98457602f605bc98636 100644 (file)
--- a/arch/arm/mach-rockchip/rk3288-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3288-board-spl.c
@@ -29,6 +29,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 u32 spl_boot_device(void)
 {
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
        const void *blob = gd->fdt_blob;
        struct udevice *dev;
        const char *bootdev;
@@ -63,10 +64,11 @@ u32 spl_boot_device(void)
        }
 
 fallback:
+#endif
        return BOOT_DEVICE_MMC1;
 }
 
-u32 spl_boot_mode(void)
+u32 spl_boot_mode(const u32 boot_device)
 {
        return MMCSD_MODE_RAW;
 }
@@ -111,8 +113,12 @@ static void configure_l2ctlr(void)
        write_l2ctlr(l2ctlr);
 }
 
+#ifdef CONFIG_SPL_MMC_SUPPORT
 static int configure_emmc(struct udevice *pinctrl)
 {
+#if !defined(CONFIG_TARGET_ROCK2) && !defined(CONFIG_TARGET_FIREFLY_RK3288) && \
+       !defined(CONFIG_TARGET_EVB_RK3288)
+
        struct gpio_desc desc;
        int ret;
 
@@ -142,10 +148,11 @@ static int configure_emmc(struct udevice *pinctrl)
                debug("gpio value ret=%d\n", ret);
                return ret;
        }
-
+#endif
        return 0;
 }
-
+#endif
+extern void back_to_bootrom(void);
 void board_init_f(ulong dummy)
 {
        struct udevice *pinctrl;
@@ -183,7 +190,7 @@ void board_init_f(ulong dummy)
        rockchip_timer_init();
        configure_l2ctlr();
 
-       ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+       ret = rockchip_get_clk(&dev);
        if (ret) {
                debug("CLK init failed: %d\n", ret);
                return;
@@ -200,6 +207,9 @@ void board_init_f(ulong dummy)
                debug("DRAM init failed: %d\n", ret);
                return;
        }
+#ifdef CONFIG_ROCKCHIP_SPL_BACK_TO_BROM
+       back_to_bootrom();
+#endif
 }
 
 static int setup_led(void)
@@ -242,6 +252,8 @@ void spl_board_init(void)
                debug("%s: Cannot find pinctrl device\n", __func__);
                goto err;
        }
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
        ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
        if (ret) {
                debug("%s: Failed to set up SD card\n", __func__);
@@ -252,6 +264,7 @@ void spl_board_init(void)
                debug("%s: Failed to set up eMMC\n", __func__);
                goto err;
        }
+#endif
 
        /* Enable debug UART */
        ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
@@ -268,3 +281,7 @@ err:
        /* No way to report error here */
        hang();
 }
+
+void lowlevel_init(void)
+{
+}