config SYS_CONFIG_NAME
default "uniphier"
-config UNIPHIER_SMP
- bool
-
choice
- prompt "UniPhier SoC select"
- optional
+ prompt "UniPhier SoC select"
+ default ARCH_UNIPHIER_PRO4
+
+config ARCH_UNIPHIER_SLD3
+ bool "UniPhier PH1-sLD3 SoC"
+ select CPU_V7
+
+config ARCH_UNIPHIER_LD4_SLD8
+ bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
+ select CPU_V7
-config MACH_PH1_PRO4
- bool "PH1-Pro4"
- select UNIPHIER_SMP
+config ARCH_UNIPHIER_PRO4
+ bool "UniPhier PH1-Pro4 SoC"
+ select CPU_V7
-config MACH_PH1_LD4
- bool "PH1-LD4"
+config ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
+ select CPU_V7
-config MACH_PH1_SLD8
- bool "PH1-sLD8"
+config ARCH_UNIPHIER_LD20
+ bool "UniPhier PH1-LD20 SoC"
+ select ARM64
+ select SPL_SEPARATE_BSS
endchoice
-choice
- prompt "UniPhier Support Card select"
- optional
+config ARCH_UNIPHIER_LD4
+ bool "Enable UniPhier PH1-LD4 SoC support"
+ depends on ARCH_UNIPHIER_LD4_SLD8
+ default y
-config PFC_MICRO_SUPPORT_CARD
- bool "Support card with PFC CPLD"
- help
- This option provides support for the expansion board with PFC
- original address mapping.
+config ARCH_UNIPHIER_SLD8
+ bool "Enable UniPhier PH1-sLD8 SoC support"
+ depends on ARCH_UNIPHIER_LD4_SLD8
+ default y
- Say Y to use the on-board UART, Ether, LED devices.
+config ARCH_UNIPHIER_PRO5
+ bool "Enable UniPhier PH1-Pro5 SoC support"
+ depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ default y
+
+config ARCH_UNIPHIER_PXS2
+ bool "Enable UniPhier ProXstream2 SoC support"
+ depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ default y
+
+config ARCH_UNIPHIER_LD6B
+ bool "Enable UniPhier PH1-LD6b SoC support"
+ depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ default y
-config DCC_MICRO_SUPPORT_CARD
- bool "Support card with DCC CPLD"
+config MICRO_SUPPORT_CARD
+ bool "Use Micro Support Card"
help
- This option provides support for the expansion board with DCC-
- arranged address mapping that is compatible with legacy UniPhier
- reference boards.
+ This option provides support for the expansion board, available
+ on some UniPhier reference boards.
Say Y to use the on-board UART, Ether, LED devices.
-endchoice
-
config CMD_PINMON
bool "Enable boot mode pins monitor command"
default y
config CMD_DDRPHY_DUMP
bool "Enable dump command of DDR PHY parameters"
+ depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
+ default y
help
The command "ddrphy" shows the resulting parameters of DDR PHY
training; it is useful for the evaluation of DDR PHY training.
-choice
- prompt "DDR3 Frequency select"
-
-config DDR_FREQ_1600
- bool "DDR3 1600"
- depends on MACH_PH1_PRO4 || MACH_PH1_LD4
-
-config DDR_FREQ_1333
- bool "DDR3 1333"
- depends on MACH_PH1_LD4 || MACH_PH1_SLD8
-
-endchoice
-
-config DDR_FREQ
- int
- default 1333 if DDR_FREQ_1333
- default 1600 if DDR_FREQ_1600
+config CMD_DDRMPHY_DUMP
+ bool "Enable dump command of DDR Multi PHY parameters"
+ depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
+ default y
+ help
+ The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
+ training; it is useful for the evaluation of DDR Multi PHY training.
endif