select ARMV7_NONSEC
select ARCH_SUPPORT_PSCI
-config ARCH_UNIPHIER_64BIT
- bool
- select ARM64
- select SPL_SEPARATE_BSS if SPL
- select ARMV8_MULTIENTRY if SPL
- select ARMV8_SPIN_TABLE if SPL
-
choice
prompt "UniPhier SoC select"
- default ARCH_UNIPHIER_PRO4
-
-config ARCH_UNIPHIER_SLD3
- bool "UniPhier sLD3 SoC"
- select ARCH_UNIPHIER_32BIT
+ default ARCH_UNIPHIER_V7_MULTI
config ARCH_UNIPHIER_LD4_SLD8
bool "UniPhier LD4/sLD8 SoCs"
select ARCH_UNIPHIER_32BIT
-config ARCH_UNIPHIER_PRO4
- bool "UniPhier Pro4 SoC"
- select ARCH_UNIPHIER_32BIT
-
-config ARCH_UNIPHIER_PRO5_PXS2_LD6B
- bool "UniPhier Pro5/PXs2/LD6b SoCs"
+config ARCH_UNIPHIER_V7_MULTI
+ bool "UniPhier Pro4/Pro5/PXs2/LD6b SoCs"
select ARCH_UNIPHIER_32BIT
-config ARCH_UNIPHIER_LD11_SINGLE
- bool "UniPhier LD11 SoC"
- select ARCH_UNIPHIER_64BIT
-
-config ARCH_UNIPHIER_LD20_SINGLE
- bool "UniPhier LD20 SoC"
- select ARCH_UNIPHIER_64BIT
-
config ARCH_UNIPHIER_V8_MULTI
bool "UniPhier V8 SoCs"
depends on !SPL
- select ARCH_UNIPHIER_64BIT
+ select ARM64
+ select CMD_UNZIP
endchoice
depends on ARCH_UNIPHIER_LD4_SLD8
default y
+config ARCH_UNIPHIER_PRO4
+ bool "Enable UniPhier Pro4 SoC support"
+ depends on ARCH_UNIPHIER_V7_MULTI
+ default y
+
config ARCH_UNIPHIER_PRO5
bool "Enable UniPhier Pro5 SoC support"
- depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ depends on ARCH_UNIPHIER_V7_MULTI
default y
config ARCH_UNIPHIER_PXS2
bool "Enable UniPhier Pxs2 SoC support"
- depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ depends on ARCH_UNIPHIER_V7_MULTI
default y
config ARCH_UNIPHIER_LD6B
bool "Enable UniPhier LD6b SoC support"
- depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
+ depends on ARCH_UNIPHIER_V7_MULTI
default y
config ARCH_UNIPHIER_LD11
- bool "Enable UniPhier LD11 SoC support" if ARCH_UNIPHIER_V8_MULTI
- depends on ARCH_UNIPHIER_LD11_SINGLE || ARCH_UNIPHIER_V8_MULTI
+ bool "Enable UniPhier LD11 SoC support"
+ depends on ARCH_UNIPHIER_V8_MULTI
default y
config ARCH_UNIPHIER_LD20
- bool "Enable UniPhier LD20 SoC support" if ARCH_UNIPHIER_V8_MULTI
- depends on ARCH_UNIPHIER_LD20_SINGLE || ARCH_UNIPHIER_V8_MULTI
+ bool "Enable UniPhier LD20 SoC support"
+ depends on ARCH_UNIPHIER_V8_MULTI
select OF_BOARD_SETUP
default y
+config ARCH_UNIPHIER_PXS3
+ bool "Enable UniPhier PXs3 SoC support"
+ depends on ARCH_UNIPHIER_V8_MULTI
+ default y
+
config CACHE_UNIPHIER
bool "Enable the UniPhier L2 cache controller"
depends on ARCH_UNIPHIER_32BIT
The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
training; it is useful for the evaluation of DDR Multi PHY training.
+config SYS_SOC
+ default "uniphier-v7" if ARCH_UNIPHIER_LD4_SLD8 || ARCH_UNIPHIER_V7_MULTI
endif