DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+/*
+ * For deriving usb clock from 100MHz sysclk, reference divisor is set
+ * to a value of 5, which gives an intermediate value 20(100/5). The
+ * multiplication factor integer is set to 24, which when multiplied to
+ * above intermediate value provides clock for usb ip.
+ */
+void usb_single_source_clk_configure(struct ccsr_usb_phy *usb_phy)
+{
+ sys_info_t sysinfo;
+
+ get_sys_info(&sysinfo);
+ if (sysinfo.diff_sysclk == 1) {
+ clrbits_be32(&usb_phy->pllprg[1],
+ CONFIG_SYS_FSL_USB_PLLPRG2_MFI);
+ setbits_be32(&usb_phy->pllprg[1],
+ CONFIG_SYS_FSL_USB_PLLPRG2_REF_DIV_INTERNAL_CLK |
+ CONFIG_SYS_FSL_USB_PLLPRG2_MFI_INTERNAL_CLK |
+ CONFIG_SYS_FSL_USB_INTERNAL_SOC_CLK_EN);
+ }
+}
+#endif
+
#ifdef CONFIG_SYS_FSL_ERRATUM_A006261
void fsl_erratum_a006261_workaround(struct ccsr_usb_phy __iomem *usb_phy)
{
}
#endif
-void cpu_init_f (void)
+ulong cpu_init_f(void)
{
+ ulong flag = 0;
extern void m8560_cpm_reset (void);
#ifdef CONFIG_SYS_DCSRBAR_PHYS
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
in_be32(&gur->dcsrcr);
#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+#ifdef CONFIG_DEEP_SLEEP
+ /* disable the console if boot from deep sleep */
+ if (in_be32(&gur->scrtsr[0]) & (1 << 3))
+ flag = GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE;
+#endif
+#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A007212
fsl_erratum_a007212_workaround();
#endif
+ return flag;
}
/* Implement a dummy function for those platforms w/o SERDES */
int enable_cluster_l2(void)
{
int i = 0;
- u32 cluster;
+ u32 cluster, svr = get_svr();
ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
struct ccsr_cluster_l2 __iomem *l2cache;
+ /* only the L2 of first cluster should be enabled as expected on T4080,
+ * but there is no EOC in the first cluster as HW sake, so return here
+ * to skip enabling L2 cache of the 2nd cluster.
+ */
+ if (SVR_SOC_VER(svr) == SVR_T4080)
+ return 0;
+
cluster = in_be32(&gur->tp_cluster[i].lower);
if (cluster & TP_CLUSTER_EOC)
return 0;
CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN |
CONFIG_SYS_FSL_USB_PLLPRG2_MFI |
CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN);
+#ifdef CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+ usb_single_source_clk_configure(usb_phy);
+#endif
setbits_be32(&usb_phy->port1.ctrl,
CONFIG_SYS_FSL_USB_CTRL_PHY_EN);
setbits_be32(&usb_phy->port1.drvvbuscfg,
}
#endif
+ init_used_tlb_cams();
return 0;
}
#endif
#ifdef CONFIG_QE
-#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
- int ret;
- size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH;
-
- /* load QE firmware from NAND flash to DDR first */
- ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_IN_NAND,
- &fw_length, (u_char *)CONFIG_SYS_QE_FW_ADDR);
-
- if (ret && ret == -EUCLEAN) {
- printf ("NAND read for QE firmware at offset %x failed %d\n",
- CONFIG_SYS_QE_FMAN_FW_IN_NAND, ret);
- }
-#endif
qe_init(qe_base);
qe_reset();
#endif