endchoice
+# subarchitectures-specific options below
+config INTEL_MID
+ bool "Intel MID platform support"
+ select REGMAP
+ select SYSCON
+ help
+ Select to build a U-Boot capable of supporting Intel MID
+ (Mobile Internet Device) platform systems which do not have
+ the PCI legacy interfaces.
+
+ If you are building for a PC class system say N here.
+
+ Intel MID platforms are based on an Intel processor and
+ chipset which consume less power than most of the x86
+ derivatives.
+
# board-specific options below
source "board/advantech/Kconfig"
source "board/congatec/Kconfig"
# platform-specific options below
source "arch/x86/cpu/baytrail/Kconfig"
+source "arch/x86/cpu/braswell/Kconfig"
source "arch/x86/cpu/broadwell/Kconfig"
source "arch/x86/cpu/coreboot/Kconfig"
source "arch/x86/cpu/ivybridge/Kconfig"
source "arch/x86/cpu/qemu/Kconfig"
source "arch/x86/cpu/quark/Kconfig"
source "arch/x86/cpu/queensbay/Kconfig"
+source "arch/x86/cpu/tangier/Kconfig"
# architecture-specific options below
config X86_RESET_VECTOR
bool
default n
+ select BINMAN
# The following options control where the 16-bit and 32-bit init lies
# If SPL is enabled then it normally holds this init code, and U-Boot proper
to work correctly. It is not exhaustive but can save time by
detecting obvious failures.
+config FLASH_DESCRIPTOR_FILE
+ string "Flash descriptor binary filename"
+ depends on HAVE_INTEL_ME
+ default "descriptor.bin"
+ help
+ The filename of the file to use as flash descriptor in the
+ board directory.
+
+config INTEL_ME_FILE
+ string "Intel Management Engine binary filename"
+ depends on HAVE_INTEL_ME
+ default "me.bin"
+ help
+ The filename of the file to use as Intel Management Engine in the
+ board directory.
+
config HAVE_FSP
bool "Add an Firmware Support Package binary"
depends on !EFI
the memory used by this initialisation process. Typically 4KB is
enough space.
+config CPU_INTEL_TURBO_NOT_PACKAGE_SCOPED
+ bool
+ help
+ This option indicates that the turbo mode setting is not package
+ scoped. i.e. turbo_enable() needs to be called on not just the
+ bootstrap processor (BSP).
+
config HAVE_VGA_BIOS
bool "Add a VGA BIOS image"
help
address of 0xfff90000 indicates that the image will be put at offset
0x90000 from the beginning of a 1MB flash device.
+config HAVE_VBT
+ bool "Add a Video BIOS Table (VBT) image"
+ depends on HAVE_FSP
+ help
+ Select this option if you have a Video BIOS Table (VBT) image that
+ you would like to add to your ROM. This is normally required if you
+ are using an Intel FSP firmware that is complaint with spec 1.1 or
+ later to initialize the integrated graphics device (IGD).
+
+ Video BIOS Table, or VBT, provides platform and board specific
+ configuration information to the driver that is not discoverable
+ or available through other means. By other means the most used
+ method here is to read EDID table from the attached monitor, over
+ Display Data Channel (DDC) using two pin I2C serial interface. VBT
+ configuration is related to display hardware and is available via
+ the ACPI OpRegion or, on older systems, in the PCI ROM (Option ROM).
+
+config VBT_FILE
+ string "Video BIOS Table (VBT) image filename"
+ depends on HAVE_VBT
+ default "vbt.bin"
+ help
+ The filename of the file to use as Video BIOS Table (VBT) image
+ in the board directory.
+
+config VBT_ADDR
+ hex "Video BIOS Table (VBT) image location"
+ depends on HAVE_VBT
+ default 0xfff90000
+ help
+ The location of Video BIOS Table (VBT) image in the SPI flash. For
+ example, base address of 0xfff90000 indicates that the image will
+ be put at offset 0x90000 from the beginning of a 1MB flash device.
+
+config VIDEO_FSP
+ bool "Enable FSP framebuffer driver support"
+ depends on HAVE_VBT && DM_VIDEO
+ help
+ Turn on this option to enable a framebuffer driver when U-Boot is
+ using Video BIOS Table (VBT) image for FSP firmware to initialize
+ the integrated graphics device.
+
+config ROM_TABLE_ADDR
+ hex
+ default 0xf0000
+ help
+ All x86 tables happen to like the address range from 0x0f0000
+ to 0x100000. We use 0xf0000 as the starting address to store
+ those tables, including PIRQ routing table, Multi-Processor
+ table and ACPI table.
+
+config ROM_TABLE_SIZE
+ hex
+ default 0x10000
+
menu "System tables"
depends on !EFI && !SYS_COREBOOT
endmenu
+config HAVE_ACPI_RESUME
+ bool "Enable ACPI S3 resume"
+ select ENABLE_MRC_CACHE
+ help
+ Select this to enable ACPI S3 resume. S3 is an ACPI-defined sleeping
+ state where all system context is lost except system memory. U-Boot
+ is responsible for restoring the machine state as it was before sleep.
+ It needs restore the memory controller, without overwriting memory
+ which is not marked as reserved. For the peripherals which lose their
+ registers, U-Boot needs to write the original value. When everything
+ is done, U-Boot needs to find out the wakeup vector provided by OSes
+ and jump there.
+
+config S3_VGA_ROM_RUN
+ bool "Re-run VGA option ROMs on S3 resume"
+ depends on HAVE_ACPI_RESUME
+ help
+ Execute VGA option ROMs in U-Boot when resuming from S3. Normally
+ this is needed when graphics console is being used in the kernel.
+
+ Turning it off can reduce some resume time, but be aware that your
+ graphics console won't work without VGA options ROMs. Set it to N
+ if your kernel is only on a serial console.
+
+config STACK_SIZE
+ hex
+ depends on HAVE_ACPI_RESUME
+ default 0x1000
+ help
+ Estimated U-Boot's runtime stack size that needs to be reserved
+ during an ACPI S3 resume.
+
config MAX_PIRQ_LINKS
int
default 8
projects / u-boot / blobdiff