#include <mpc512x.h>
#include <asm/bitops.h>
#include <command.h>
+#include <fdt_support.h>
+#ifdef CONFIG_MISC_INIT_R
+#include <i2c.h>
+#endif
/* Clocks in use */
#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \
CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \
CLOCK_SCCR1_PSCFIFO_EN | \
CLOCK_SCCR1_DDR_EN | \
- CLOCK_SCCR1_FEC_EN)
+ CLOCK_SCCR1_FEC_EN | \
+ CLOCK_SCCR1_PCI_EN | \
+ CLOCK_SCCR1_TPR_EN)
#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \
CLOCK_SCCR2_SPDIF_EN | \
+ CLOCK_SCCR2_DIU_EN | \
CLOCK_SCCR2_I2C_EN)
#define CSAW_START(start) ((start) & 0xFFFF0000)
* Without this the flash identification routine fails, as it needs to issue
* write commands in order to establish the device ID.
*/
- *((volatile u8 *)(CFG_CPLD_BASE + 0x08)) = 0xC1;
+#ifdef CONFIG_ADS5121_REV2
+ *((volatile u8 *)(CFG_CPLD_BASE + 0x08)) = 0xC1;
+#else
+ if (*((u8 *)(CFG_CPLD_BASE + 0x08)) & 0x04) {
+ *((volatile u8 *)(CFG_CPLD_BASE + 0x08)) = 0xC1;
+ } else {
+ /* running from Backup flash */
+ *((volatile u8 *)(CFG_CPLD_BASE + 0x08)) = 0x32;
+ }
+#endif
+ /*
+ * Configure Flash Speed
+ */
+ *((volatile u32 *)(CFG_IMMR + LPC_OFFSET + CS0_CONFIG)) = CFG_CS0_CFG;
/*
* Enable clocks
*/
return 0;
}
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
u32 msize = 0;
u32 i;
/* Initialize IO Control */
- im->io_ctrl.regs[MEM_IDX] = IOCTRL_MUX_DDR;
+ im->io_ctrl.regs[IOCTL_MEM/4] = IOCTRL_MUX_DDR;
/* Initialize DDR Local Window */
im->sysconf.ddrlaw.bar = CFG_DDR_BASE & 0xFFFFF000;
im->mddrc.prioman_config2 = CFG_MDDRCGRP_PM_CFG2;
im->mddrc.hiprio_config = CFG_MDDRCGRP_HIPRIO_CFG;
im->mddrc.lut_table0_main_upper = CFG_MDDRCGRP_LUT0_MU;
- im->mddrc.lut_table1_main_upper = CFG_MDDRCGRP_LUT1_MU;
- im->mddrc.lut_table2_main_upper = CFG_MDDRCGRP_LUT2_MU;
- im->mddrc.lut_table3_main_upper = CFG_MDDRCGRP_LUT3_MU;
- im->mddrc.lut_table4_main_upper = CFG_MDDRCGRP_LUT4_MU;
im->mddrc.lut_table0_main_lower = CFG_MDDRCGRP_LUT0_ML;
+ im->mddrc.lut_table1_main_upper = CFG_MDDRCGRP_LUT1_MU;
im->mddrc.lut_table1_main_lower = CFG_MDDRCGRP_LUT1_ML;
+ im->mddrc.lut_table2_main_upper = CFG_MDDRCGRP_LUT2_MU;
im->mddrc.lut_table2_main_lower = CFG_MDDRCGRP_LUT2_ML;
+ im->mddrc.lut_table3_main_upper = CFG_MDDRCGRP_LUT3_MU;
im->mddrc.lut_table3_main_lower = CFG_MDDRCGRP_LUT3_ML;
+ im->mddrc.lut_table4_main_upper = CFG_MDDRCGRP_LUT4_MU;
im->mddrc.lut_table4_main_lower = CFG_MDDRCGRP_LUT4_ML;
im->mddrc.lut_table0_alternate_upper = CFG_MDDRCGRP_LUT0_AU;
+ im->mddrc.lut_table0_alternate_lower = CFG_MDDRCGRP_LUT0_AL;
im->mddrc.lut_table1_alternate_upper = CFG_MDDRCGRP_LUT1_AU;
- im->mddrc.lut_table2_alternate_upper = CFG_MDDRCGRP_LUT2_AU;
- im->mddrc.lut_table3_alternate_upper = CFG_MDDRCGRP_LUT3_AU;
- im->mddrc.lut_table4_alternate_upper = CFG_MDDRCGRP_LUT4_AU;
- im->mddrc.lut_table0_alternate_lower = CFG_MDDRCGRP_LUT0_AU;
im->mddrc.lut_table1_alternate_lower = CFG_MDDRCGRP_LUT1_AL;
+ im->mddrc.lut_table2_alternate_upper = CFG_MDDRCGRP_LUT2_AU;
im->mddrc.lut_table2_alternate_lower = CFG_MDDRCGRP_LUT2_AL;
+ im->mddrc.lut_table3_alternate_upper = CFG_MDDRCGRP_LUT3_AU;
im->mddrc.lut_table3_alternate_lower = CFG_MDDRCGRP_LUT3_AL;
+ im->mddrc.lut_table4_alternate_upper = CFG_MDDRCGRP_LUT4_AU;
im->mddrc.lut_table4_alternate_lower = CFG_MDDRCGRP_LUT4_AL;
/* Initialize MDDRC */
for (i = 0; i < 10; i++)
im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_RFSH;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_RFSH;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_INIT_DEV_OP;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_EM2;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
im->mddrc.ddr_command = CFG_MICRON_EM2;
im->mddrc.ddr_command = CFG_MICRON_EM3;
im->mddrc.ddr_command = CFG_MICRON_EN_DLL;
- im->mddrc.ddr_command = CFG_MICRON_RST_DLL;
+ im->mddrc.ddr_command = CFG_MICRON_INIT_DEV_OP;
im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
im->mddrc.ddr_command = CFG_MICRON_RFSH;
im->mddrc.ddr_command = CFG_MICRON_INIT_DEV_OP;
im->mddrc.ddr_command = CFG_MICRON_OCD_DEFAULT;
- im->mddrc.ddr_command = CFG_MICRON_OCD_EXIT;
-
- for (i = 0; i < 10; i++)
- im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
/* Start MDDRC */
im->mddrc.ddr_time_config0 = CFG_MDDRC_TIME_CFG0_RUN;
return msize;
}
+int misc_init_r(void)
+{
+ u8 tmp_val;
+ extern int ads5121_diu_init(void);
+
+ /* Using this for DIU init before the driver in linux takes over
+ * Enable the TFP410 Encoder (I2C address 0x38)
+ */
+
+ i2c_set_bus_num(2);
+ tmp_val = 0xBF;
+ i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
+ /* Verify if enabled */
+ tmp_val = 0;
+ i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
+ debug("DVI Encoder Read: 0x%02lx\n", tmp_val);
+
+ tmp_val = 0x10;
+ i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
+ /* Verify if enabled */
+ tmp_val = 0;
+ i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
+ debug("DVI Encoder Read: 0x%02lx\n", tmp_val);
+
+#ifdef CONFIG_FSL_DIU_FB
+#if !(defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE))
+ ads5121_diu_init();
+#endif
+#endif
+
+ return 0;
+}
+static iopin_t ioregs_init[] = {
+ /* FUNC1=FEC_RX_DV Sets Next 3 to FEC pads */
+ {
+ IOCTL_SPDIF_TXCLK, 3, 0,
+ IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
+ },
+ /* Set highest Slew on 9 PATA pins */
+ {
+ IOCTL_PATA_CE1, 9, 1,
+ IO_PIN_FMUX(0) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
+ },
+ /* FUNC1=FEC_COL Sets Next 15 to FEC pads */
+ {
+ IOCTL_PSC0_0, 15, 0,
+ IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
+ },
+ /* FUNC1=SPDIF_TXCLK */
+ {
+ IOCTL_LPC_CS1, 1, 0,
+ IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
+ },
+ /* FUNC2=SPDIF_TX and sets Next pin to SPDIF_RX */
+ {
+ IOCTL_I2C1_SCL, 2, 0,
+ IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
+ },
+ /* FUNC2=DIU CLK */
+ {
+ IOCTL_PSC6_0, 1, 0,
+ IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
+ },
+ /* FUNC2=DIU_HSYNC */
+ {
+ IOCTL_PSC6_1, 1, 0,
+ IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
+ },
+ /* FUNC2=DIUVSYNC Sets Next 26 to DIU Pads */
+ {
+ IOCTL_PSC6_4, 26, 0,
+ IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
+ IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
+ }
+};
+
int checkboard (void)
{
ushort brd_rev = *(vu_short *) (CFG_CPLD_BASE + 0x00);
printf ("Board: ADS5121 rev. 0x%04x (CPLD rev. 0x%02x)\n",
brd_rev, cpld_rev);
+ /* initialize function mux & slew rate IO inter alia on IO Pins */
+
+
+ iopin_initialize(ioregs_init, sizeof(ioregs_init) / sizeof(ioregs_init[0]));
+
return 0;
}
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize);
+}
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
projects / u-boot / blobdiff