/*
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
-#include <ppc4xx.h>
+#include <asm/ppc4xx.h>
#include <asm/processor.h>
+#include <asm/io.h>
#include <spd_sdram.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+DECLARE_GLOBAL_DATA_PTR;
-extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+
+static inline u32 get_async_pci_freq(void)
+{
+ if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) &
+ CONFIG_SYS_BCSR5_PCI66EN)
+ return 66666666;
+ else
+ return 33333333;
+}
int board_early_init_f(void)
{
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
-
- mtebc(pb0ap, 0x03017300); /* FLASH/SRAM */
- mtebc(pb0cr, 0xfc0da000); /* BAS=0xfc0 64MB r/w 16-bit */
-
- mtebc(pb1ap, 0x00000000);
- mtebc(pb1cr, 0x00000000);
-
- mtebc(pb2ap, 0x04814500);
- /*CPLD*/ mtebc(pb2cr, 0x80018000); /*BAS=0x800 1MB r/w 8-bit */
-
- mtebc(pb3ap, 0x00000000);
- mtebc(pb3cr, 0x00000000);
-
- mtebc(pb4ap, 0x00000000);
- mtebc(pb4cr, 0x00000000);
-
- mtebc(pb5ap, 0x00000000);
- mtebc(pb5cr, 0x00000000);
-
- /*--------------------------------------------------------------------
- * Setup the interrupt controller polarities, triggers, etc.
- *-------------------------------------------------------------------*/
- mtdcr(uic0sr, 0xffffffff); /* clear all */
- mtdcr(uic0er, 0x00000000); /* disable all */
- mtdcr(uic0cr, 0x00000009); /* ATI & UIC1 crit are critical */
- mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */
- mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */
- mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic0sr, 0xffffffff); /* clear all */
-
- mtdcr(uic1sr, 0xffffffff); /* clear all */
- mtdcr(uic1er, 0x00000000); /* disable all */
- mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */
- mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */
- mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic1sr, 0xffffffff); /* clear all */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* Setup the GPIO pins
*-------------------------------------------------------------------*/
/*CPLD cs */
- /*setup Address lines for flash sizes larger than 16Meg. */
- out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x40010000);
- out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40010000);
- out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x40000000);
+ /*setup Address lines for flash size 64Meg. */
+ out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x50010000);
+ out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x50010000);
+ out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x50000000);
/*setup emac */
out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080);
out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x00080000);
out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x00010000);
+ /* external interrupts IRQ0...3 */
+ out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000);
+ out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00);
+ out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500);
+
+#ifdef CONFIG_440EP
/*setup USB 2.0 */
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000);
out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000);
out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf);
out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa);
out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500);
+#endif
+
+ /*--------------------------------------------------------------------
+ * Setup the interrupt controller polarities, triggers, etc.
+ *-------------------------------------------------------------------*/
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000009); /* ATI & UIC1 crit are critical */
+ mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
/*--------------------------------------------------------------------
* Setup other serial configuration
*-------------------------------------------------------------------*/
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */
- mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
+ mtsdr(SDR0_PFC0, 0x00003e00); /* Pin function */
+ mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins */
+
+ /* Check and reconfigure the PCI sync clock if necessary */
+ ppc4xx_pci_sync_clock_config(get_async_pci_freq());
/*clear tmrclk divisor */
- *(unsigned char *)(CFG_BCSR_BASE | 0x04) = 0x00;
+ *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x04) = 0x00;
/*enable ethernet */
- *(unsigned char *)(CFG_BCSR_BASE | 0x08) = 0xf0;
+ *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x08) = 0xf0;
+#ifdef CONFIG_440EP
/*enable usb 1.1 fs device and remove usb 2.0 reset */
- *(unsigned char *)(CFG_BCSR_BASE | 0x09) = 0x00;
+ *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x09) = 0x00;
+#endif
/*get rid of flash write protect */
- *(unsigned char *)(CFG_BCSR_BASE | 0x07) = 0x40;
+ *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x07) = 0x00;
return 0;
}
int misc_init_r (void)
{
- DECLARE_GLOBAL_DATA_PTR;
uint pbcr;
int size_val = 0;
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
+
+ /* adjust flash start and offset */
+ gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+ gd->bd->bi_flashoffset = 0;
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- -CFG_MONITOR_LEN,
+ -CONFIG_SYS_MONITOR_LEN,
0xffffffff,
&flash_info[0]);
int checkboard(void)
{
- sys_info_t sysinfo;
- unsigned char *s = getenv("serial#");
-
- get_sys_info(&sysinfo);
+ char buf[64];
+ int i = getenv_f("serial#", buf, sizeof(buf));
+ u8 rev;
+ u32 clock = get_async_pci_freq();
+#ifdef CONFIG_440EP
printf("Board: Yosemite - AMCC PPC440EP Evaluation Board");
- if (s != NULL) {
+#else
+ printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board");
+#endif
+
+ rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0));
+ printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000);
+
+ if (i > 0) {
puts(", serial# ");
- puts(s);
+ puts(buf);
}
putc('\n');
- printf("\tVCO: %lu MHz\n", sysinfo.freqVCOMhz / 1000000);
- printf("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000);
- printf("\tPLB: %lu MHz\n", sysinfo.freqPLB / 1000000);
- printf("\tOPB: %lu MHz\n", sysinfo.freqOPB / 1000000);
- printf("\tEPB: %lu MHz\n", sysinfo.freqEPB / 1000000);
- printf("\tPCI: %lu MHz\n", sysinfo.freqPCI / 1000000);
+ /*
+ * Reconfiguration of the PCI sync clock is already done,
+ * now check again if everything is in range:
+ */
+ if (ppc4xx_pci_sync_clock_config(clock)) {
+ printf("ERROR: PCI clocking incorrect (async=%d "
+ "sync=%ld)!\n", clock, get_PCI_freq());
+ }
return (0);
}
/*************************************************************************
- * sdram_init -- doesn't use serial presence detect.
+ * initdram -- doesn't use serial presence detect.
*
* Assumes: 256 MB, ECC, non-registered
* PLB @ 133 MHz
*
************************************************************************/
-void sdram_init(void)
+#define NUM_TRIES 64
+#define NUM_READS 10
+
+void sdram_tr1_set(int ram_address, int* tr1_value)
+{
+ int i;
+ int j, k;
+ volatile unsigned int* ram_pointer = (unsigned int*)ram_address;
+ int first_good = -1, last_bad = 0x1ff;
+
+ unsigned long test[NUM_TRIES] = {
+ 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
+ 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
+ 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
+ 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
+ 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
+ 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
+ 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
+ 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
+ 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
+ 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
+ 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
+ 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
+ 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
+ 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
+ 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
+ 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 };
+
+ /* go through all possible SDRAM0_TR1[RDCT] values */
+ for (i=0; i<=0x1ff; i++) {
+ /* set the current value for TR1 */
+ mtsdram(SDRAM0_TR1, (0x80800800 | i));
+
+ /* write values */
+ for (j=0; j<NUM_TRIES; j++) {
+ ram_pointer[j] = test[j];
+
+ /* clear any cache at ram location */
+ __asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
+ }
+
+ /* read values back */
+ for (j=0; j<NUM_TRIES; j++) {
+ for (k=0; k<NUM_READS; k++) {
+ /* clear any cache at ram location */
+ __asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
+
+ if (ram_pointer[j] != test[j])
+ break;
+ }
+
+ /* read error */
+ if (k != NUM_READS) {
+ break;
+ }
+ }
+
+ /* we have a SDRAM0_TR1[RDCT] that is part of the window */
+ if (j == NUM_TRIES) {
+ if (first_good == -1)
+ first_good = i; /* found beginning of window */
+ } else { /* bad read */
+ /* if we have not had a good read then don't care */
+ if(first_good != -1) {
+ /* first failure after a good read */
+ last_bad = i-1;
+ break;
+ }
+ }
+ }
+
+ /* return the current value for TR1 */
+ *tr1_value = (first_good + last_bad) / 2;
+}
+
+phys_size_t initdram(int board)
{
register uint reg;
+ int tr1_bank1, tr1_bank2;
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram(mem_clktr, 0x40000000); /* ?? */
- mtsdram(mem_wddctr, 0x40000000); /* ?? */
+ mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram(SDRAM0_CLKTR, 0x40000000); /* ?? */
+ mtsdram(SDRAM0_WDDCTR, 0x40000000); /* ?? */
/*clear this first, if the DDR is enabled by a debugger
- then you can not make changes. */
- mtsdram(mem_cfg0, 0x00000000); /* Disable EEC */
+ then you can not make changes. */
+ mtsdram(SDRAM0_CFG0, 0x00000000); /* Disable EEC */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram(mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram(mem_b1cr, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */
-
- mtsdram(mem_tr0, 0x410a4012); /* ?? */
- mtsdram(mem_tr1, 0x8080080b); /* ?? */
- mtsdram(mem_rtr, 0x04080000); /* ?? */
- mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
- mtsdram(mem_cfg0, 0x34000000); /* Disable EEC */
+ mtsdram(SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram(SDRAM0_B1CR, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */
+
+ mtsdram(SDRAM0_TR0, 0x410a4012); /* ?? */
+ mtsdram(SDRAM0_RTR, 0x04080000); /* ?? */
+ mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
+ mtsdram(SDRAM0_CFG0, 0x30000000); /* Disable EEC */
udelay(400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram(mem_cfg0, 0x84000000); /* Enable */
+ mtsdram(SDRAM0_CFG0, 0x80000000); /* Enable */
for (;;) {
- mfsdram(mem_mcsts, reg);
+ mfsdram(SDRAM0_MCSTS, reg);
if (reg & 0x80000000)
break;
}
-}
-
-/*************************************************************************
- * long int initdram
- *
- ************************************************************************/
-long int initdram(int board)
-{
- sdram_init();
- return CFG_SDRAM_BANKS * (CFG_KBYTES_SDRAM * 1024); /* return bytes */
-}
-
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long strap;
- unsigned long addr;
-
- /*--------------------------------------------------------------------------+
- * Bamboo is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
- if ((strap & SDR0_SDSTP1_PAE_MASK) == 0) {
- printf("PCI: SDR0_STRP1[PAE] not set.\n");
- printf("PCI: Configuration aborted.\n");
- return 0;
- }
+ sdram_tr1_set(0x00000000, &tr1_bank1);
+ sdram_tr1_set(0x08000000, &tr1_bank2);
+ mtsdram(SDRAM0_TR1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
-
- /* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
-
- return 1;
+ return CONFIG_SYS_SDRAM_BANKS * (CONFIG_SYS_KBYTES_SDRAM * 1024); /* return bytes */
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CFG_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
-
-/*************************************************************************
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Bamboo is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
/*************************************************************************
* hw_watchdog_reset
}
#endif
+
+void board_reset(void)
+{
+ /* give reset to BCSR */
+ *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x06) = 0x09;
+}