#include <common.h>
#include <netdev.h>
+#include <asm/io.h>
+#include "arm-ebi.h"
+#include "integrator-sc.h"
DECLARE_GLOBAL_DATA_PTR;
int board_init (void)
{
+ u32 val;
+
/* arch number of Integrator Board */
#ifdef CONFIG_ARCH_CINTEGRATOR
gd->bd->bi_arch_number = MACH_TYPE_CINTEGRATOR;
cm_remap(); /* remaps writeable memory to 0x00000000 */
#endif
+#ifdef CONFIG_ARCH_CINTEGRATOR
+ /*
+ * Flash protection on the Integrator/CP is in a simple register
+ */
+ val = readl(CP_FLASHPROG);
+ val |= (CP_FLASHPROG_FLVPPEN | CP_FLASHPROG_FLWREN);
+ writel(val, CP_FLASHPROG);
+#else
+ /*
+ * The Integrator/AP has some special protection mechanisms
+ * for the external memories, first the External Bus Interface (EBI)
+ * then the system controller (SC).
+ *
+ * The system comes up with the flash memory non-writable and
+ * configuration locked. If we want U-Boot to be used for flash
+ * access we cannot have the flash memory locked.
+ */
+ writel(EBI_UNLOCK_MAGIC, EBI_BASE + EBI_LOCK_REG);
+ val = readl(EBI_BASE + EBI_CSR1_REG);
+ val &= EBI_CSR_WREN_MASK;
+ val |= EBI_CSR_WREN_ENABLE;
+ writel(val, EBI_BASE + EBI_CSR1_REG);
+ writel(0, EBI_BASE + EBI_LOCK_REG);
+
+ /*
+ * Set up the system controller to remove write protection from
+ * the flash memory and enable Vpp
+ */
+ writel(SC_CTRL_FLASHVPP | SC_CTRL_FLASHWP, SC_CTRLS);
+#endif
+
icache_enable ();
return 0;
int misc_init_r (void)
{
-#ifdef CONFIG_PCI
- pci_init();
-#endif
setenv("verify", "n");
return (0);
}
-/******************************
- Routine:
- Description:
-******************************/
+/*
+ * The Integrator remaps the Flash memory to 0x00000000 and executes U-Boot
+ * from there, which means we cannot test the RAM underneath the ROM at this
+ * point. It will be unmapped later on, when we are executing from the
+ * relocated in RAM U-Boot. We simply assume that this RAM is usable if the
+ * RAM on higher addresses works fine.
+ */
+#define REMAPPED_FLASH_SZ 0x40000
+
int dram_init (void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
#ifdef CONFIG_CM_SPD_DETECT
{
extern void dram_query(void);
- unsigned long cm_reg_sdram;
- unsigned long sdram_shift;
+ u32 cm_reg_sdram;
+ u32 sdram_shift;
dram_query(); /* Assembler accesses to CM registers */
/* Queries the SPD values */
/* Obtain the SDRAM size from the CM SDRAM register */
- cm_reg_sdram = *(volatile ulong *)(CM_BASE + OS_SDRAM);
+ cm_reg_sdram = readl(CM_BASE + OS_SDRAM);
/* Register SDRAM size
*
* 0xXXXXXXbbb000bb 16 MB
* 0xXXXXXXbbb100bb 256 MB
*
*/
- sdram_shift = ((cm_reg_sdram & 0x0000001C)/4)%4;
- gd->bd->bi_dram[0].size = 0x01000000 << sdram_shift;
-
+ sdram_shift = ((cm_reg_sdram & 0x0000001C)/4)%4;
+ gd->ram_size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE +
+ REMAPPED_FLASH_SZ,
+ 0x01000000 << sdram_shift);
}
+#else
+ gd->ram_size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE +
+ REMAPPED_FLASH_SZ,
+ PHYS_SDRAM_1_SIZE);
#endif /* CM_SPD_DETECT */
+ /* We only have one bank of RAM, set it to whatever was detected */
+ gd->bd->bi_dram[0].size = gd->ram_size;
return 0;
}
#ifdef CONFIG_SMC91111
rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
#endif
-#ifdef CONFIG_PCI
rc += pci_eth_init(bis);
-#endif
return rc;
}
#endif