*/
#include <common.h>
+#include <debug_uart.h>
#include <asm/io.h>
+#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_pmc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
+#include <linux/mtd/rawnand.h>
#include <atmel_lcdc.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
+#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
unsigned long csa;
/* Enable CS3 */
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
- writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
+ at91_periph_clk_enable(ATMEL_ID_PIOC);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
}
#endif
-#ifdef CONFIG_CMD_USB
-static void at91sam9m10g45ek_usb_hw_init(void)
-{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
- writel(1 << ATMEL_ID_PIODE, &pmc->pcer);
+void at91_spl_board_init(void)
+{
+ /*
+ * On the at91sam9m10g45ek board, the chip wm9711 stays in the
+ * test mode, so it needs do some action to exit test mode.
+ */
+ at91_periph_clk_enable(ATMEL_ID_PIODE);
+ at91_set_gpio_output(AT91_PIN_PD7, 0);
+ at91_set_gpio_output(AT91_PIN_PD8, 0);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
+
+#ifdef CONFIG_SD_BOOT
+ at91_mci_hw_init();
+#elif CONFIG_NAND_BOOT
+ at91sam9m10g45ek_nand_hw_init();
+#endif
+}
- at91_set_gpio_output(AT91_PIN_PD1, 0);
- at91_set_gpio_output(AT91_PIN_PD3, 0);
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_14 |
+ ATMEL_MPDDRC_CR_DQMS_SHARED |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
+
+ ddr2->rtr = 0x24b;
+
+ ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
+ 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
+ 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
+ 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
}
-#endif
-#ifdef CONFIG_MACB
-static void at91sam9m10g45ek_macb_hw_init(void)
+void mem_init(void)
{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
- struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
+ struct atmel_mpddrc_config ddr2;
- /* Enable clock */
- writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
+ ddr2_conf(&ddr2);
- /*
- * Disable pull-up on:
- * RXDV (PA15) => PHY normal mode (not Test mode)
- * ERX0 (PA12) => PHY ADDR0
- * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- &pioa->pudr);
+ at91_system_clk_enable(AT91_PMC_DDR);
- at91_phy_reset();
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2);
+}
+#endif
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- &pioa->puer);
+#ifdef CONFIG_CMD_USB
+static void at91sam9m10g45ek_usb_hw_init(void)
+{
+ at91_periph_clk_enable(ATMEL_ID_PIODE);
- /* And the pins. */
- at91_macb_hw_init();
+ at91_set_gpio_output(AT91_PIN_PD1, 0);
+ at91_set_gpio_output(AT91_PIN_PD3, 0);
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
- vl_col: 480,
- vl_row: 272,
- vl_clk: 9000000,
- vl_sync: ATMEL_LCDC_INVLINE_NORMAL |
- ATMEL_LCDC_INVFRAME_NORMAL,
- vl_bpix: 3,
- vl_tft: 1,
- vl_hsync_len: 45,
- vl_left_margin: 1,
- vl_right_margin:1,
- vl_vsync_len: 1,
- vl_upper_margin:40,
- vl_lower_margin:1,
- mmio : ATMEL_BASE_LCDC,
+ .vl_col = 480,
+ .vl_row = 272,
+ .vl_clk = 9000000,
+ .vl_sync = ATMEL_LCDC_INVLINE_NORMAL |
+ ATMEL_LCDC_INVFRAME_NORMAL,
+ .vl_bpix = 3,
+ .vl_tft = 1,
+ .vl_hsync_len = 45,
+ .vl_left_margin = 1,
+ .vl_right_margin = 1,
+ .vl_vsync_len = 1,
+ .vl_upper_margin = 40,
+ .vl_lower_margin = 1,
+ .mmio = ATMEL_BASE_LCDC,
};
static void at91sam9m10g45ek_lcd_hw_init(void)
{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */
at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */
at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */
at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */
at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */
- writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
+ at91_periph_clk_enable(ATMEL_ID_LCDC);
gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
}
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += nand_info[i].size;
+ nand_size += get_nand_dev_by_index(i)->size;
lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
dram_size >> 20,
nand_size >> 20 );
#endif /* CONFIG_LCD_INFO */
#endif
-int board_early_init_f(void)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
at91_seriald_hw_init();
+}
+#endif
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
#ifdef CONFIG_CMD_USB
at91sam9m10g45ek_usb_hw_init();
#endif
-#ifdef CONFIG_HAS_DATAFLASH
- at91_spi0_hw_init(1 << 0);
-#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 4);
-#endif
-#ifdef CONFIG_MACB
- at91sam9m10g45ek_macb_hw_init();
-#endif
#ifdef CONFIG_LCD
at91sam9m10g45ek_lcd_hw_init();
#endif
{
}
#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
-#endif
- return rc;
-}
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < 2;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch(slave->cs) {
- case 1:
- at91_set_gpio_output(AT91_PIN_PB18, 0);
- break;
- case 0:
- default:
- at91_set_gpio_output(AT91_PIN_PB3, 0);
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch(slave->cs) {
- case 1:
- at91_set_gpio_output(AT91_PIN_PB18, 1);
- break;
- case 0:
- default:
- at91_set_gpio_output(AT91_PIN_PB3, 1);
- break;
- }
-}
-#endif /* CONFIG_ATMEL_SPI */
projects / u-boot / blobdiff