#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
-#include <asm/immap_fsl_pci.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
#include <asm/io.h>
+#include <asm/mmu.h>
#include <spd_sdram.h>
#include <miiphy.h>
#include <libfdt.h>
#include <fdt_support.h>
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
long int fixed_sdram(void);
int board_early_init_f (void)
int checkboard (void)
{
- volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR);
- volatile ccsr_local_ecm_t *ecm = (void *)(CFG_MPC85xx_ECM_ADDR);
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
+ volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
if ((uint)&gur->porpllsr != 0xe00e0000) {
- printf("immap size error %x\n",&gur->porpllsr);
+ printf("immap size error %lx\n",(ulong)&gur->porpllsr);
}
printf ("Board: ATUM8548\n");
************************************************************************/
long int fixed_sdram (void)
{
- volatile ccsr_ddr_t *ddr= (void *)(CFG_MPC85xx_DDR_ADDR);
-
- ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
- ddr->cs0_config = CFG_DDR_CS0_CONFIG;
- ddr->timing_cfg_0 = CFG_DDR_TIMING_0;
- ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
- ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
- ddr->sdram_mode = CFG_DDR_MODE;
- ddr->sdram_interval = CFG_DDR_INTERVAL;
+ volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
+
+ ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
+ ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
+ ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
+ ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
+ ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
+ ddr->sdram_mode = CONFIG_SYS_DDR_MODE;
+ ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
#if defined (CONFIG_DDR_ECC)
ddr->err_disable = 0x0000000D;
ddr->err_sbe = 0x00ff0000;
udelay(500);
#if defined (CONFIG_DDR_ECC)
/* Enable ECC checking */
- ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000);
+ ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
#else
- ddr->sdram_cfg = CFG_DDR_CONTROL;
+ ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
#endif
asm("sync; isync; msync");
udelay(500);
- return CFG_SDRAM_SIZE * 1024 * 1024;
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
-long int
+phys_size_t
initdram(int board_type)
{
long dram_size = 0;
puts("Initializing\n");
#if defined(CONFIG_SPD_EEPROM)
- puts("spd_sdram\n");
- dram_size = spd_sdram ();
+ puts("fsl_ddr_sdram\n");
+ dram_size = fsl_ddr_sdram();
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
#else
puts("fixed_sdram\n");
dram_size = fixed_sdram ();
#endif
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize and enable DDR ECC.
- */
- ddr_enable_ecc(dram_size);
-#endif
puts(" DDR: ");
return dram_size;
}
-#if defined(CFG_DRAM_TEST)
+#if defined(CONFIG_SYS_DRAM_TEST)
int
testdram(void)
{
- uint *pstart = (uint *) CFG_MEMTEST_START;
- uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
+ uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
uint *p;
printf("Testing DRAM from 0x%08x to 0x%08x\n",
- CFG_MEMTEST_START,
- CFG_MEMTEST_END);
+ CONFIG_SYS_MEMTEST_START,
+ CONFIG_SYS_MEMTEST_END);
printf("DRAM test phase 1:\n");
for (p = pstart; p < pend; p++) {
static struct pci_controller pcie1_hose;
#endif
-int first_free_busno=0;
-
-void
-pci_init_board(void)
+void pci_init_board(void)
{
- volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ struct fsl_pci_info pci_info[3];
+ u32 devdisr, pordevsr, io_sel;
+ u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel;
+ int first_free_busno = 0;
+ int num = 0;
+
+ int pcie_ep, pcie_configured;
- uint devdisr = gur->devdisr;
- uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
- uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
+ devdisr = in_be32(&gur->devdisr);
+ pordevsr = in_be32(&gur->pordevsr);
+ porpllsr = in_be32(&gur->porpllsr);
+ io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
- debug (" pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
- devdisr, io_sel, host_agent);
+ debug (" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);
/* explicitly set 'Clock out select register' to echo SYSCLK input to our CPLD */
- gur->clkocr |= MPC85xx_ATUM_CLKOCR;
+ setbits_be32(&gur->clkocr, MPC85xx_ATUM_CLKOCR);
if (io_sel & 1) {
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII1_DIS))
- printf (" eTSEC1 is in sgmii mode.\n");
+ printf("eTSEC1 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
- printf (" eTSEC2 is in sgmii mode.\n");
+ printf("eTSEC2 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
- printf (" eTSEC3 is in sgmii mode.\n");
+ printf("eTSEC3 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII4_DIS))
- printf (" eTSEC4 is in sgmii mode.\n");
+ printf("eTSEC4 is in sgmii mode.\n");
}
#ifdef CONFIG_PCIE1
- {
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE1_ADDR;
- extern void fsl_pci_init(struct pci_controller *hose);
- struct pci_controller *hose = &pcie1_hose;
- int pcie_ep = (host_agent == 5);
- int pcie_configured = io_sel & 6;
+ pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
- printf ("\n PCIE1 connected to slot as %s (base address %x)",
- pcie_ep ? "End Point" : "Root Complex",
- (uint)pci);
- if (pci->pme_msg_det) {
- pci->pme_msg_det = 0xffffffff;
- debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
- }
- printf ("\n");
-
- /* inbound */
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEMORY_BUS,
- CFG_PCI_MEMORY_PHYS,
- CFG_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY);
-
+ SET_STD_PCIE_INFO(pci_info[num], 1);
+ pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
+#ifdef CONFIG_SYS_PCIE1_MEM_BUS2
/* outbound memory */
- pci_set_region(hose->regions + 1,
- CFG_PCIE1_MEM_BASE,
- CFG_PCIE1_MEM_PHYS,
- CFG_PCIE1_MEM_SIZE,
+ pci_set_region(&pcie1_hose.regions[0],
+ CONFIG_SYS_PCIE1_MEM_BUS2,
+ CONFIG_SYS_PCIE1_MEM_PHYS2,
+ CONFIG_SYS_PCIE1_MEM_SIZE2,
PCI_REGION_MEM);
- /* outbound io */
- pci_set_region(hose->regions + 2,
- CFG_PCIE1_IO_BASE,
- CFG_PCIE1_IO_PHYS,
- CFG_PCIE1_IO_SIZE,
- PCI_REGION_IO);
-
- hose->region_count = 3;
-#ifdef CFG_PCIE1_MEM_BASE2
- /* outbound memory */
- pci_set_region(hose->regions + 3,
- CFG_PCIE1_MEM_BASE2,
- CFG_PCIE1_MEM_PHYS2,
- CFG_PCIE1_MEM_SIZE2,
- PCI_REGION_MEM);
- hose->region_count++;
+ pcie1_hose.region_count = 1;
#endif
- hose->first_busno=first_free_busno;
-
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
-
- first_free_busno=hose->last_busno+1;
- printf(" PCIE1 on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
+ printf ("PCIE1: connected to Slot as %s (base addr %lx)\n",
+ pcie_ep ? "Endpoint" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie1_hose, first_free_busno);
} else {
- printf (" PCIE1: disabled\n");
+ printf("PCIE1: disabled\n");
}
- }
+ puts("\n");
#else
- gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE); /* disable */
#endif
#ifdef CONFIG_PCI1
-{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI1_ADDR;
- extern void fsl_pci_init(struct pci_controller *hose);
- struct pci_controller *hose = &pci1_hose;
-
- uint pci_agent = (host_agent == 6);
- uint pci_speed = 33333000; /*get_clock_freq (); PCI PSPEED in [4:5] */
- uint pci_32 = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32; /* PORDEVSR[15] */
- uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; /* PORDEVSR[14] */
- uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; /* PORPLLSR[16] */
+ pci_speed = 33333000; /*get_clock_freq (); PCI PSPEED in [4:5] */
+ pci_32 = pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32; /* PORDEVSR[15] */
+ pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
+ pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
- printf ("\n PCI1: %d bit, %s MHz, %s, %s, %s (base address %x)\n",
+ SET_STD_PCI_INFO(pci_info[num], 1);
+ pci_agent = fsl_setup_hose(&pci1_hose, pci_info[num].regs);
+ printf("PCI1: %d bit, %s MHz, %s, %s, %s (base address %lx)\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333000) ? "33" :
(pci_speed == 66666000) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter",
- (uint)pci
- );
-
- /* inbound */
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEMORY_BUS,
- CFG_PCI_MEMORY_PHYS,
- CFG_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY);
-
- /* outbound memory */
- pci_set_region(hose->regions + 1,
- CFG_PCI1_MEM_BASE,
- CFG_PCI1_MEM_PHYS,
- CFG_PCI1_MEM_SIZE,
- PCI_REGION_MEM);
+ pci_info[num].regs);
- /* outbound io */
- pci_set_region(hose->regions + 2,
- CFG_PCI1_IO_BASE,
- CFG_PCI1_IO_PHYS,
- CFG_PCI1_IO_SIZE,
- PCI_REGION_IO);
- hose->region_count = 3;
- hose->first_busno=first_free_busno;
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
- first_free_busno=hose->last_busno+1;
- printf ("PCI1 on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pci1_hose, first_free_busno);
} else {
- printf (" PCI1: disabled\n");
+ printf("PCI1: disabled\n");
}
-}
+
+ puts("\n");
#else
- gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
#endif
#ifdef CONFIG_PCI2
-{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI2_ADDR;
- extern void fsl_pci_init(struct pci_controller *hose);
- struct pci_controller *hose = &pci2_hose;
-
if (!(devdisr & MPC85xx_DEVDISR_PCI2)) {
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEMORY_BUS,
- CFG_PCI_MEMORY_PHYS,
- CFG_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY);
-
- pci_set_region(hose->regions + 1,
- CFG_PCI2_MEM_BASE,
- CFG_PCI2_MEM_PHYS,
- CFG_PCI2_MEM_SIZE,
- PCI_REGION_MEM);
+ SET_STD_PCI_INFO(pci_info[num], 2);
+ pci_agent = fsl_setup_hose(&pci2_hose, pci_info[num].regs);
- pci_set_region(hose->regions + 2,
- CFG_PCI2_IO_BASE,
- CFG_PCI2_IO_PHYS,
- CFG_PCI2_IO_SIZE,
- PCI_REGION_IO);
- hose->region_count = 3;
- hose->first_busno=first_free_busno;
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
- first_free_busno=hose->last_busno+1;
- printf ("PCI2 on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
+ puts("PCI2\n");
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pci1_hose, first_free_busno);
} else {
- printf (" PCI2: disabled\n");
+ printf("PCI2: disabled\n");
}
-}
+ puts("\n");
#else
- gur->devdisr |= MPC85xx_DEVDISR_PCI2;
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI2); /* disable */
#endif
}
}
#if defined(CONFIG_OF_BOARD_SETUP)
-
-void
-ft_board_setup(void *blob, bd_t *bd)
+void ft_board_setup(void *blob, bd_t *bd)
{
- int node, tmp[2];
- const char *path;
-
ft_cpu_setup(blob, bd);
- node = fdt_path_offset(blob, "/aliases");
- tmp[0] = 0;
- if (node >= 0) {
-#ifdef CONFIG_PCI1
- path = fdt_getprop(blob, node, "pci0", NULL);
- if (path) {
- tmp[1] = pci1_hose.last_busno - pci1_hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-#endif
-#ifdef CONFIG_PCI2
- path = fdt_getprop(blob, node, "pci1", NULL);
- if (path) {
- tmp[1] = pci2_hose.last_busno - pci2_hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-#endif
-#ifdef CONFIG_PCIE1
- path = fdt_getprop(blob, node, "pci2", NULL);
- if (path) {
- tmp[1] = pcie1_hose.last_busno - pcie1_hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-#endif
- }
+ FT_FSL_PCI_SETUP;
}
#endif
projects / u-boot / blobdiff