#include <config.h>
#include <malloc.h>
#include <asm/blackfin.h>
+#include <asm/portmux.h>
#include <asm/mach-common/bits/dma.h>
-#include <i2c.h>
+#include <spi.h>
#include <linux/types.h>
#include <stdio_dev.h>
-#define DMA_SIZE16 2
-
#include <asm/mach-common/bits/ppi.h>
#include <asm/mach-common/bits/timer.h>
-#include <asm/bfin_logo_230x230.h>
-
#define LCD_X_RES 320 /* Horizontal Resolution */
#define LCD_Y_RES 240 /* Vertical Resolution */
-#define LCD_BPP 24 /* Bit Per Pixel */
-#define LCD_PIXEL_SIZE (LCD_BPP / 8)
+#define DMA_BUS_SIZE 16
+
+#ifdef CONFIG_BF527_EZKIT_REV_2_1 /* lq035q1 */
+
+#if !defined(CONFIG_LQ035Q1_USE_RGB888_8_BIT_PPI) && \
+ !defined(CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI)
+# define CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
+#endif
+
+/* Interface 16/18-bit TFT over an 8-bit wide PPI using a
+ * small Programmable Logic Device (CPLD)
+ * http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165
+ */
+
+#ifdef CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
+#include <asm/bfin_logo_rgb565_230x230.h>
+#define LCD_BPP 16 /* Bit Per Pixel */
+#define CLOCKS_PPIX 2 /* Clocks per pixel */
+#define CPLD_DELAY 3 /* RGB565 pipeline delay */
+#endif
+
+#ifdef CONFIG_LQ035Q1_USE_RGB888_8_BIT_PPI
+#include <asm/bfin_logo_230x230.h>
+#define LCD_BPP 24 /* Bit Per Pixel */
+#define CLOCKS_PPIX 3 /* Clocks per pixel */
+#define CPLD_DELAY 5 /* RGB888 pipeline delay */
+#endif
+
+/*
+ * HS and VS timing parameters (all in number of PPI clk ticks)
+ */
+
+#define H_ACTPIX (LCD_X_RES * CLOCKS_PPIX) /* active horizontal pixel */
+#define H_PERIOD (336 * CLOCKS_PPIX) /* HS period */
+#define H_PULSE (2 * CLOCKS_PPIX) /* HS pulse width */
+#define H_START (7 * CLOCKS_PPIX + CPLD_DELAY) /* first valid pixel */
+
+#define U_LINE 4 /* Blanking Lines */
-#define DMA_BUS_SIZE 16
-#define LCD_CLK (12*1000*1000) /* 12MHz */
+#define V_LINES (LCD_Y_RES + U_LINE) /* total vertical lines */
+#define V_PULSE (2 * CLOCKS_PPIX) /* VS pulse width (1-5 H_PERIODs) */
+#define V_PERIOD (H_PERIOD * V_LINES) /* VS period */
+
+#define ACTIVE_VIDEO_MEM_OFFSET ((U_LINE / 2) * LCD_X_RES * (LCD_BPP / 8))
-#define CLOCKS_PER_PIX 3
+/*
+ * LCD Modes
+ */
+#define LQ035_RL (0 << 8) /* Right -> Left Scan */
+#define LQ035_LR (1 << 8) /* Left -> Right Scan */
+#define LQ035_TB (1 << 9) /* Top -> Botton Scan */
+#define LQ035_BT (0 << 9) /* Botton -> Top Scan */
+#define LQ035_BGR (1 << 11) /* Use BGR format */
+#define LQ035_RGB (0 << 11) /* Use RGB format */
+#define LQ035_NORM (1 << 13) /* Reversal */
+#define LQ035_REV (0 << 13) /* Reversal */
+
+#define LQ035_INDEX 0x74
+#define LQ035_DATA 0x76
+
+#define LQ035_DRIVER_OUTPUT_CTL 0x1
+#define LQ035_SHUT_CTL 0x11
+
+#define LQ035_DRIVER_OUTPUT_MASK (LQ035_LR | LQ035_TB | LQ035_BGR | LQ035_REV)
+#define LQ035_DRIVER_OUTPUT_DEFAULT (0x2AEF & ~LQ035_DRIVER_OUTPUT_MASK)
+
+#define LQ035_SHUT (1 << 0) /* Shutdown */
+#define LQ035_ON (0 << 0) /* Shutdown */
+
+#ifndef CONFIG_LQ035Q1_LCD_MODE
+#define CONFIG_LQ035Q1_LCD_MODE (LQ035_NORM | LQ035_RL | LQ035_TB | LQ035_BGR)
+#endif
+
+#else /* t350mcqb */
+#include <asm/bfin_logo_230x230.h>
+
+#define LCD_BPP 24 /* Bit Per Pixel */
+#define CLOCKS_PPIX 3 /* Clocks per pixel */
/* HS and VS timing parameters (all in number of PPI clk ticks) */
-#define H_ACTPIX (LCD_X_RES * CLOCKS_PER_PIX) /* active horizontal pixel */
-#define H_PERIOD (408 * CLOCKS_PER_PIX) /* HS period */
+#define H_ACTPIX (LCD_X_RES * CLOCKS_PPIX) /* active horizontal pixel */
+#define H_PERIOD (408 * CLOCKS_PPIX) /* HS period */
#define H_PULSE 90 /* HS pulse width */
#define H_START 204 /* first valid pixel */
#define U_LINE 1 /* Blanking Lines */
-#define V_LINES (LCD_Y_RES + U_LINE) /* total vertical lines */
+#define V_LINES (LCD_Y_RES + U_LINE) /* total vertical lines */
#define V_PULSE (3 * H_PERIOD) /* VS pulse width (1-5 H_PERIODs) */
#define V_PERIOD (H_PERIOD * V_LINES) /* VS period */
#define ACTIVE_VIDEO_MEM_OFFSET (U_LINE * H_ACTPIX)
+#endif
+
+#define LCD_PIXEL_SIZE (LCD_BPP / 8)
+#define DMA_SIZE16 2
#define PPI_TX_MODE 0x2
#define PPI_XFER_TYPE_11 0xC
#define PPI_PACK_EN 0x80
#define PPI_POLS_1 0x8000
+#ifdef CONFIG_BF527_EZKIT_REV_2_1
+static struct spi_slave *slave;
+static int lq035q1_control(unsigned char reg, unsigned short value)
+{
+ int ret;
+ u8 regs[3] = {LQ035_INDEX, 0, 0};
+ u8 data[3] = {LQ035_DATA, 0, 0};
+ u8 dummy[3];
+
+ regs[2] = reg;
+ data[1] = value >> 8;
+ data[2] = value & 0xFF;
+
+ if (!slave) {
+ /* FIXME: Verify the max SCK rate */
+ slave = spi_setup_slave(CONFIG_LQ035Q1_SPI_BUS,
+ CONFIG_LQ035Q1_SPI_CS, 20000000,
+ SPI_MODE_3);
+ if (!slave)
+ return -1;
+ }
+
+ if (spi_claim_bus(slave))
+ return -1;
+
+ ret = spi_xfer(slave, 24, regs, dummy, SPI_XFER_BEGIN | SPI_XFER_END);
+ ret |= spi_xfer(slave, 24, data, dummy, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ spi_release_bus(slave);
+
+ return ret;
+}
+#endif
+
/* enable and disable PPI functions */
void EnablePPI(void)
{
- *pPPI_CONTROL |= PORT_EN;
+ bfin_write_PPI_CONTROL(bfin_read_PPI_CONTROL() | PORT_EN);
}
void DisablePPI(void)
{
- *pPPI_CONTROL &= ~PORT_EN;
+ bfin_write_PPI_CONTROL(bfin_read_PPI_CONTROL() & ~PORT_EN);
}
void Init_Ports(void)
{
- *pPORTF_MUX &= ~PORT_x_MUX_0_MASK;
- *pPORTF_MUX |= PORT_x_MUX_0_FUNC_1;
- *pPORTF_FER |= PF0 | PF1 | PF2 | PF3 | PF4 | PF5 | PF6 | PF7;
-
- *pPORTG_MUX &= ~PORT_x_MUX_1_MASK;
- *pPORTG_MUX |= PORT_x_MUX_1_FUNC_1;
- *pPORTG_FER |= PG5;
+ const unsigned short pins[] = {
+ P_PPI0_D0, P_PPI0_D1, P_PPI0_D2, P_PPI0_D3, P_PPI0_D4,
+ P_PPI0_D5, P_PPI0_D6, P_PPI0_D7, P_PPI0_FS2, 0,
+ };
+ peripheral_request_list(pins, "lcd");
}
void Init_PPI(void)
{
- *pPPI_DELAY = H_START;
- *pPPI_COUNT = (H_ACTPIX-1);
- *pPPI_FRAME = 0;
+ bfin_write_PPI_DELAY(H_START);
+ bfin_write_PPI_COUNT(H_ACTPIX - 1);
+ bfin_write_PPI_FRAME(V_LINES);
/* PPI control, to be replaced with definitions */
- *pPPI_CONTROL = PPI_TX_MODE | /* output mode , PORT_DIR */
+ bfin_write_PPI_CONTROL(
+ PPI_TX_MODE | /* output mode , PORT_DIR */
PPI_XFER_TYPE_11 | /* sync mode XFR_TYPE */
PPI_PORT_CFG_01 | /* two frame sync PORT_CFG */
PPI_PACK_EN | /* packing enabled PACK_EN */
- PPI_POLS_1; /* faling edge syncs POLS */
+ PPI_POLS_1 /* faling edge syncs POLS */
+ );
}
void Init_DMA(void *dst)
{
- *pDMA0_START_ADDR = dst;
+ bfin_write_DMA0_START_ADDR(dst);
/* X count */
- *pDMA0_X_COUNT = H_ACTPIX / 2;
- *pDMA0_X_MODIFY = DMA_BUS_SIZE / 8;
+ bfin_write_DMA0_X_COUNT(H_ACTPIX / 2);
+ bfin_write_DMA0_X_MODIFY(DMA_BUS_SIZE / 8);
/* Y count */
- *pDMA0_Y_COUNT = V_LINES;
- *pDMA0_Y_MODIFY = DMA_BUS_SIZE / 8;
+ bfin_write_DMA0_Y_COUNT(V_LINES);
+ bfin_write_DMA0_Y_MODIFY(DMA_BUS_SIZE / 8);
/* DMA Config */
- *pDMA0_CONFIG =
+ bfin_write_DMA0_CONFIG(
WDSIZE_16 | /* 16 bit DMA */
DMA2D | /* 2D DMA */
- FLOW_AUTO; /* autobuffer mode */
+ FLOW_AUTO /* autobuffer mode */
+ );
}
-
void EnableDMA(void)
{
- *pDMA0_CONFIG |= DMAEN;
+ bfin_write_DMA0_CONFIG(bfin_read_DMA0_CONFIG() | DMAEN);
}
void DisableDMA(void)
{
- *pDMA0_CONFIG &= ~DMAEN;
+ bfin_write_DMA0_CONFIG(bfin_read_DMA0_CONFIG() & ~DMAEN);
}
-
/* Init TIMER0 as Frame Sync 1 generator */
void InitTIMER0(void)
{
- *pTIMER_DISABLE |= TIMDIS0; /* disable Timer */
+ bfin_write_TIMER_DISABLE(TIMDIS0); /* disable Timer */
SSYNC();
- *pTIMER_STATUS |= TIMIL0 | TOVF_ERR0 | TRUN0; /* clear status */
+ bfin_write_TIMER_STATUS(TIMIL0 | TOVF_ERR0 | TRUN0); /* clear status */
SSYNC();
- *pTIMER0_PERIOD = H_PERIOD;
+ bfin_write_TIMER0_PERIOD(H_PERIOD);
SSYNC();
- *pTIMER0_WIDTH = H_PULSE;
+ bfin_write_TIMER0_WIDTH(H_PULSE);
SSYNC();
- *pTIMER0_CONFIG = PWM_OUT |
+ bfin_write_TIMER0_CONFIG(
+ PWM_OUT |
PERIOD_CNT |
TIN_SEL |
CLK_SEL |
- EMU_RUN;
+ EMU_RUN
+ );
SSYNC();
}
void EnableTIMER0(void)
{
- *pTIMER_ENABLE |= TIMEN0;
+ bfin_write_TIMER_ENABLE(TIMEN0);
SSYNC();
}
void DisableTIMER0(void)
{
- *pTIMER_DISABLE |= TIMDIS0;
+ bfin_write_TIMER_DISABLE(TIMDIS0);
SSYNC();
}
void InitTIMER1(void)
{
- *pTIMER_DISABLE |= TIMDIS1; /* disable Timer */
+ bfin_write_TIMER_DISABLE(TIMDIS1); /* disable Timer */
SSYNC();
- *pTIMER_STATUS |= TIMIL1 | TOVF_ERR1 | TRUN1; /* clear status */
+ bfin_write_TIMER_STATUS(TIMIL1 | TOVF_ERR1 | TRUN1); /* clear status */
SSYNC();
-
- *pTIMER1_PERIOD = V_PERIOD;
+ bfin_write_TIMER1_PERIOD(V_PERIOD);
SSYNC();
- *pTIMER1_WIDTH = V_PULSE;
+ bfin_write_TIMER1_WIDTH(V_PULSE);
SSYNC();
- *pTIMER1_CONFIG = PWM_OUT |
+ bfin_write_TIMER1_CONFIG(
+ PWM_OUT |
PERIOD_CNT |
TIN_SEL |
CLK_SEL |
- EMU_RUN;
+ EMU_RUN
+ );
SSYNC();
}
void EnableTIMER1(void)
{
- *pTIMER_ENABLE |= TIMEN1;
+ bfin_write_TIMER_ENABLE(TIMEN1);
SSYNC();
}
void DisableTIMER1(void)
{
- *pTIMER_DISABLE |= TIMDIS1;
+ bfin_write_TIMER_DISABLE(TIMDIS1);
+ SSYNC();
+}
+
+void EnableTIMER12(void)
+{
+ bfin_write_TIMER_ENABLE(TIMEN1 | TIMEN0);
SSYNC();
}
int video_init(void *dst)
{
+#ifdef CONFIG_BF527_EZKIT_REV_2_1
+ lq035q1_control(LQ035_SHUT_CTL, LQ035_ON);
+ lq035q1_control(LQ035_DRIVER_OUTPUT_CTL, (CONFIG_LQ035Q1_LCD_MODE &
+ LQ035_DRIVER_OUTPUT_MASK) | LQ035_DRIVER_OUTPUT_DEFAULT);
+#endif
Init_Ports();
Init_DMA(dst);
EnableDMA();
Init_PPI();
EnablePPI();
+#ifdef CONFIG_BF527_EZKIT_REV_2_1
+ EnableTIMER12();
+#else
/* Frame sync 2 (VS) needs to start at least one PPI clk earlier */
EnableTIMER1();
/* Add Some Delay ... */
/* now start frame sync 1 */
EnableTIMER0();
+#endif
return 0;
}
}
+void video_stop(void)
+{
+ DisablePPI();
+ DisableDMA();
+ DisableTIMER0();
+ DisableTIMER1();
+#ifdef CONFIG_BF527_EZKIT_REV_2_1
+ lq035q1_control(LQ035_SHUT_CTL, LQ035_SHUT);
+#endif
+}
+
void video_putc(const char c)
{
}