+// SPDX-License-Identifier: GPL-2.0+
/*
* Board functions for Compulab CM-FX6 board
*
* Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
*
* Author: Nikita Kiryanov <nikita@compulab.co.il>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <ahci.h>
#include <dm.h>
#include <dwc_ahsata.h>
+#include <environment.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <mtd_node.h>
#define CM_FX6_SATA_INIT_RETRIES 10
-# if !CONFIG_IS_ENABLED(AHCI)
-int sata_initialize(void)
-{
- int err, i;
-
- /* Make sure this gpio has logical 0 value */
- gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
- udelay(100);
- cm_fx6_sata_power(1);
-
- for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
- err = setup_sata();
- if (err) {
- printf("SATA setup failed: %d\n", err);
- return err;
- }
-
- udelay(100);
-
- err = __sata_initialize();
- if (!err)
- break;
-
- /* There is no device on the SATA port */
- if (sata_port_status(0, 0) == 0)
- break;
-
- /* There's a device, but link not established. Retry */
- }
-
- return err;
-}
-
-int sata_stop(void)
-{
- __sata_stop();
- cm_fx6_sata_power(0);
- mdelay(250);
-
- return 0;
-}
-# endif
#else
static int cm_fx6_setup_issd(void) { return 0; }
#endif
static void cm_fx6_setup_gpmi_nand(void) {}
#endif
-#ifdef CONFIG_FSL_ESDHC
-static struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC1_BASE_ADDR},
- {USDHC2_BASE_ADDR},
- {USDHC3_BASE_ADDR},
-};
-
-static enum mxc_clock usdhc_clk[3] = {
- MXC_ESDHC_CLK,
- MXC_ESDHC2_CLK,
- MXC_ESDHC3_CLK,
-};
-
-int board_mmc_init(bd_t *bis)
-{
- int i;
-
- cm_fx6_set_usdhc_iomux();
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- usdhc_cfg[i].sdhc_clk = mxc_get_clock(usdhc_clk[i]);
- usdhc_cfg[i].max_bus_width = 4;
- fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- enable_usdhc_clk(1, i);
- }
-
- return 0;
-}
-#endif
-
#ifdef CONFIG_MXC_SPI
int cm_fx6_setup_ecspi(void)
{
return 0;
}
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ char baseboard_name[16];
+ int err;
+
+ if (is_mx6dq())
+ env_set("board_rev", "MX6Q");
+ else if (is_mx6dl())
+ env_set("board_rev", "MX6DL");
+
+ err = cl_eeprom_get_product_name((uchar *)baseboard_name, 0);
+ if (err)
+ return 0;
+
+ if (!strncmp("SB-FX6m", baseboard_name, 7))
+ env_set("board_name", "Utilite");
+#endif
+ return 0;
+}
+
int checkboard(void)
{
puts("Board: CM-FX6\n");