* Copyright (C) 2004 Texas Instruments.
*
* ----------------------------------------------------------------------------
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * SPDX-License-Identifier: GPL-2.0+
* ----------------------------------------------------------------------------
*/
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
-#include "../common/psc.h"
-#include "../common/misc.h"
+#include <asm/arch/davinci_misc.h>
DECLARE_GLOBAL_DATA_PTR;
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
- /* Workaround for TMS320DM6446 errata 1.3.22 */
- REG(PSC_SILVER_BULLET) = 0;
+ /* Configure AEMIF pins (although this should be configured at boot time
+ * with pull-up/pull-down resistors) */
+ REG(PINMUX0) = 0x00000c1f;
+
+ davinci_errata_workarounds();
/* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
- lpsc_on(DAVINCI_LPSC_I2C);
- lpsc_on(DAVINCI_LPSC_UART0);
- lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
lpsc_on(DAVINCI_LPSC_USB);
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= 1;
-
- /* Enable EMAC and AEMIF pins */
- REG(PINMUX0) = 0x80000c1f;
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= (1 << 7);
-
- /* Set the Bus Priority Register to appropriate value */
- REG(VBPR) = 0x20;
+ davinci_enable_uart0();
+ davinci_enable_emac();
+ davinci_enable_i2c();
+ lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
uint8_t video_mode;
uint8_t eeprom_enetaddr[6];
- dv_display_clk_infos();
-
/* Read Ethernet MAC address from EEPROM if available. */
if (dvevm_read_mac_address(eeprom_enetaddr))
- dv_configure_mac_address(eeprom_enetaddr);
-
- if (!eth_hw_init())
- printf("ethernet init failed!\n");
+ davinci_sync_env_enetaddr(eeprom_enetaddr);
i2c_read(0x39, 0x00, 1, &video_mode, 1);