#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
- /* Workaround for TMS320DM6446 errata 1.3.22 */
- REG(PSC_SILVER_BULLET) = 0;
+ davinci_errata_workarounds();
/* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
- lpsc_on(DAVINCI_LPSC_I2C);
- lpsc_on(DAVINCI_LPSC_UART0);
- lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
-#if !defined(CFG_USE_DSPLINK)
+#if !defined(CONFIG_SYS_USE_DSPLINK)
/* Powerup the DSP */
dsp_on();
-#endif /* CFG_USE_DSPLINK */
-
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= 1;
+#endif /* CONFIG_SYS_USE_DSPLINK */
- /* Enable EMAC and AEMIF pins */
- REG(PINMUX0) = 0x80000c1f;
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= (1 << 7);
-
- /* Set the Bus Priority Register to appropriate value */
- REG(VBPR) = 0x20;
+ davinci_enable_uart0();
+ davinci_enable_emac();
+ davinci_enable_i2c();
+ lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
u_int32_t value, mac[2], address;
/* Read Integrity data structure checkword. */
- if (i2c_read(CFG_I2C_EEPROM_ADDR, INTEGRITY_CHECKWORD_OFFSET,
- CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, INTEGRITY_CHECKWORD_OFFSET,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
goto err;
if (value != INTEGRITY_CHECKWORD_VALUE)
return 0;
/* Read SYSCFG structure offset. */
- if (i2c_read(CFG_I2C_EEPROM_ADDR, INTEGRITY_SYSCFG_OFFSET,
- CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, INTEGRITY_SYSCFG_OFFSET,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
goto err;
address = 0x800 + (int) value; /* Address of SYSCFG structure. */
/* Read NET CONFIG structure offset. */
- if (i2c_read(CFG_I2C_EEPROM_ADDR, address,
- CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, address,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
goto err;
address = 0x800 + (int) value; /* Address of NET CONFIG structure. */
address += 12; /* Address of NET INTERFACE CONFIG structure. */
/* Read NET INTERFACE CONFIG 2 structure offset. */
- if (i2c_read(CFG_I2C_EEPROM_ADDR, address,
- CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, address,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
goto err;
address = 0x800 + 16 + (int) value; /* Address of NET INTERFACE
* CONFIG 2 structure. */
/* Read MAC address. */
- if (i2c_read(CFG_I2C_EEPROM_ADDR, address,
- CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &mac[0], 8))
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, address,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &mac[0], 8))
goto err;
buf[0] = mac[0] >> 24;
return 1; /* Found */
err:
- printf("Read from EEPROM @ 0x%02x failed\n", CFG_I2C_EEPROM_ADDR);
+ printf("Read from EEPROM @ 0x%02x failed\n", CONFIG_SYS_I2C_EEPROM_ADDR);
return 0;
}
dv_display_clk_infos();
/* Configure I2C switch (PCA9543) to enable channel 0. */
- i2cbuf = CFG_I2C_PCA9543_ENABLE_CH0;
- if (i2c_write(CFG_I2C_PCA9543_ADDR, 0,
- CFG_I2C_PCA9543_ADDR_LEN, &i2cbuf, 1)) {
- printf("Write to MUX @ 0x%02x failed\n", CFG_I2C_PCA9543_ADDR);
+ i2cbuf = CONFIG_SYS_I2C_PCA9543_ENABLE_CH0;
+ if (i2c_write(CONFIG_SYS_I2C_PCA9543_ADDR, 0,
+ CONFIG_SYS_I2C_PCA9543_ADDR_LEN, &i2cbuf, 1)) {
+ printf("Write to MUX @ 0x%02x failed\n", CONFIG_SYS_I2C_PCA9543_ADDR);
return 1;
}
if (!eth_hw_init())
printf("Ethernet init failed\n");
- /* On this platform, U-Boot is copied in RAM by the UBL,
- * so we are always in the relocated state. */
- gd->flags |= GD_FLG_RELOC;
-
return(0);
}