int board_early_init_f(void)
{
/* IO0 clock at 480MHz */
- mx28_set_ioclk(MXC_IOCLK0, 480000);
+ mxs_set_ioclk(MXC_IOCLK0, 480000);
/* IO1 clock at 480MHz */
- mx28_set_ioclk(MXC_IOCLK1, 480000);
+ mxs_set_ioclk(MXC_IOCLK1, 480000);
/* SSP0 clock at 96MHz */
- mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
- /* SSP2 clock at 96MHz */
- mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+ mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
+ /* SSP2 clock at 160MHz */
+ mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
#ifdef CONFIG_CMD_USB
mxs_iomux_setup_pad(MX28_PAD_SSP2_SS1__USB1_OVERCURRENT);
mxs_iomux_setup_pad(MX28_PAD_AUART3_TX__GPIO_3_13 |
MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP);
gpio_direction_output(MX28_PAD_AUART3_TX__GPIO_3_13, 0);
+
+ mxs_iomux_setup_pad(MX28_PAD_AUART3_RX__GPIO_3_12 |
+ MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP);
+ gpio_direction_output(MX28_PAD_AUART3_RX__GPIO_3_12, 0);
#endif
return 0;
int dram_init(void)
{
- return mx28_dram_init();
+ return mxs_dram_init();
}
#ifdef CONFIG_CMD_MMC
{
/* Configure WP as input. */
gpio_direction_input(MX28_PAD_AUART2_CTS__GPIO_3_10);
+ /* Turn on the power to the card. */
+ gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
- return mxsmmc_initialize(bis, 0, m28_mmc_wp);
+ return mxsmmc_initialize(bis, 0, m28_mmc_wp, NULL);
}
#endif
int fecmxc_mii_postcall(int phy)
{
+#if defined(CONFIG_DENX_M28_V11) || defined(CONFIG_DENX_M28_V10)
+ /* KZ8031 PHY on old boards. */
+ const uint32_t freq = 0x0080;
+#else
+ /* KZ8021 PHY on new boards. */
+ const uint32_t freq = 0x0000;
+#endif
+
miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
if (phy == 3)
- miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+ miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8100 | freq);
return 0;
}
int board_eth_init(bd_t *bis)
{
- struct mx28_clkctrl_regs *clkctrl_regs =
- (struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+ struct mxs_clkctrl_regs *clkctrl_regs =
+ (struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
struct eth_device *dev;
int ret;
CLKCTRL_ENET_TIME_SEL_MASK | CLKCTRL_ENET_CLK_OUT_EN,
CLKCTRL_ENET_TIME_SEL_RMII_CLK);
+#if !defined(CONFIG_DENX_M28_V11) && !defined(CONFIG_DENX_M28_V10)
+ /* Reset the new PHY */
+ gpio_direction_output(MX28_PAD_AUART2_RTS__GPIO_3_11, 0);
+ udelay(10000);
+ gpio_set_value(MX28_PAD_AUART2_RTS__GPIO_3_11, 1);
+ udelay(10000);
+#endif
+
ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
if (ret) {
printf("FEC MXS: Unable to init FEC0\n");