* Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
* Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <libfdt.h>
#include <fdt_support.h>
-#include <ppc440.h>
+#include <asm/ppc440.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/bitops.h>
#include <miiphy.h>
#endif
#include <serial.h>
+#include <asm/4xx_pci.h>
+
#include "fpga.h"
#include "pmc440.h"
*/
mfsdr(SDR0_PINSTP, val);
if (((val & 0xf0000000) >> 29) != 7)
- return &serial1_device;
+ return &eserial2_device;
ulong scratchreg = in_be32((void*)GPIO0_ISR3L);
if (!(scratchreg & 0x80)) {
}
if (scratchreg & 0x01)
- return &serial1_device;
+ return &eserial2_device;
else
- return &serial0_device;
+ return &eserial1_device;
}
int board_early_init_f(void)
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
- mtdcr(PLB4_ACR, reg);
+ reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
+ mtdcr(PLB4A0_ACR, reg);
#ifdef CONFIG_FPGA
pmc440_init_fpga();
/*
* Assign interrupts to PCI devices. Some OSs rely on this.
*/
-void pmc440_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
unsigned char int_line[] = {IRQ_PCIC, IRQ_PCID, IRQ_PCIA, IRQ_PCIB};
}
#endif
-/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#ifdef CONFIG_PCI_PNP
- hose->fixup_irq = pmc440_pci_fixup_irq;
-#endif
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
/*
* pci_target_init
*
/* No error reporting */
pci_hose_write_config_word(hose, 0, PCI_ERREN, 0);
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
if (!is_monarch()) {
/* Program the board's subsystem id/classcode */
pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_ID,
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
/*
- * pci_master_init
+ * Override weak default pci_master_init()
*/
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
- unsigned short temp_short;
-
/*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
+ * Only configure the master in monach mode
*/
- if (is_monarch()) {
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
- }
+ if (is_monarch())
+ __pci_master_init(hose);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
static void wait_for_pci_ready(void)
{
- int i;
- char *s = getenv("pcidelay");
- /*
- * We have our own handling of the pcidelay variable.
- * Using CONFIG_PCI_BOOTDELAY enables pausing for host
- * and adapter devices. For adapter devices we do not
- * want this.
- */
- if (s) {
- int ms = simple_strtoul(s, NULL, 10);
- printf("PCI: Waiting for %d ms\n", ms);
- for (i=0; i<ms; i++)
- udelay(1000);
- }
-
if (!(in_be32((void*)GPIO1_IR) & GPIO1_PPC_EREADY)) {
printf("PCI: Waiting for EREADY (CTRL-C to skip) ... ");
while (1) {
}
#endif /* defined(CONFIG_PCI) */
-#if defined(CONFIG_POST)
-/*
- * Returns 1 if keys pressed to start the power-on long-running tests
- * Called from board_init_f().
- */
-int post_hotkeys_pressed(void)
-{
- return 0; /* No hotkeys supported */
-}
-#endif /* CONFIG_POST */
-
#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
projects / u-boot / blobdiff