* Use default console on P4 when strapping jumper
* is installed (bootstrap option != 'H').
*/
- mfsdr(SDR_PINSTP, val);
+ mfsdr(SDR0_PINSTP, val);
if (((val & 0xf0000000) >> 29) != 7)
return &serial1_device;
u32 reg;
/* general EBC configuration (disable EBC timeouts) */
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xf8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xf8400000);
/*
* Setup the GPIO pins
* TODO: setup GPIOs via CONFIG_SYS_4xx_GPIO_TABLE in board's config file
*/
- out32(GPIO0_OR, 0x40000102);
- out32(GPIO0_TCR, 0x4c90011f);
- out32(GPIO0_OSRL, 0x28051400);
- out32(GPIO0_OSRH, 0x55005000);
- out32(GPIO0_TSRL, 0x08051400);
- out32(GPIO0_TSRH, 0x55005000);
- out32(GPIO0_ISR1L, 0x54000000);
- out32(GPIO0_ISR1H, 0x00000000);
- out32(GPIO0_ISR2L, 0x44000000);
- out32(GPIO0_ISR2H, 0x00000100);
- out32(GPIO0_ISR3L, 0x00000000);
- out32(GPIO0_ISR3H, 0x00000000);
-
- out32(GPIO1_OR, 0x80002408);
- out32(GPIO1_TCR, 0xd6003c08);
- out32(GPIO1_OSRL, 0x0a5a0000);
- out32(GPIO1_OSRH, 0x00000000);
- out32(GPIO1_TSRL, 0x00000000);
- out32(GPIO1_TSRH, 0x00000000);
- out32(GPIO1_ISR1L, 0x00005555);
- out32(GPIO1_ISR1H, 0x40000000);
- out32(GPIO1_ISR2L, 0x04010000);
- out32(GPIO1_ISR2H, 0x00000000);
- out32(GPIO1_ISR3L, 0x01400000);
- out32(GPIO1_ISR3H, 0x00000000);
+ out_be32((void *)GPIO0_OR, 0x40000102);
+ out_be32((void *)GPIO0_TCR, 0x4c90011f);
+ out_be32((void *)GPIO0_OSRL, 0x28051400);
+ out_be32((void *)GPIO0_OSRH, 0x55005000);
+ out_be32((void *)GPIO0_TSRL, 0x08051400);
+ out_be32((void *)GPIO0_TSRH, 0x55005000);
+ out_be32((void *)GPIO0_ISR1L, 0x54000000);
+ out_be32((void *)GPIO0_ISR1H, 0x00000000);
+ out_be32((void *)GPIO0_ISR2L, 0x44000000);
+ out_be32((void *)GPIO0_ISR2H, 0x00000100);
+ out_be32((void *)GPIO0_ISR3L, 0x00000000);
+ out_be32((void *)GPIO0_ISR3H, 0x00000000);
+
+ out_be32((void *)GPIO1_OR, 0x80002408);
+ out_be32((void *)GPIO1_TCR, 0xd6003c08);
+ out_be32((void *)GPIO1_OSRL, 0x0a5a0000);
+ out_be32((void *)GPIO1_OSRH, 0x00000000);
+ out_be32((void *)GPIO1_TSRL, 0x00000000);
+ out_be32((void *)GPIO1_TSRH, 0x00000000);
+ out_be32((void *)GPIO1_ISR1L, 0x00005555);
+ out_be32((void *)GPIO1_ISR1H, 0x40000000);
+ out_be32((void *)GPIO1_ISR2L, 0x04010000);
+ out_be32((void *)GPIO1_ISR2H, 0x00000000);
+ out_be32((void *)GPIO1_ISR3L, 0x01400000);
+ out_be32((void *)GPIO1_ISR3H, 0x00000000);
/* patch PLB:PCI divider for 66MHz PCI */
- mfcpr(clk_spcid, reg);
+ mfcpr(CPR0_SPCID, reg);
if (pci_is_66mhz() && (reg != 0x02000000)) {
- mtcpr(clk_spcid, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */
+ mtcpr(CPR0_SPCID, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */
- mfcpr(clk_icfg, reg);
+ mfcpr(CPR0_ICFG, reg);
reg |= CPR0_ICFG_RLI_MASK;
- mtcpr(clk_icfg, reg);
+ mtcpr(CPR0_ICFG, reg);
- mtspr(dbcr0, 0x20000000); /* do chip reset */
+ mtspr(SPRN_DBCR0, 0x20000000); /* do chip reset */
}
/*
* Setup the interrupt controller polarities, triggers, etc.
*/
- mtdcr(uic0sr, 0xffffffff); /* clear all */
- mtdcr(uic0er, 0x00000000); /* disable all */
- mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */
- mtdcr(uic0pr, 0xfffff7ef);
- mtdcr(uic0tr, 0x00000000);
- mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(uic0sr, 0xffffffff); /* clear all */
-
- mtdcr(uic1sr, 0xffffffff); /* clear all */
- mtdcr(uic1er, 0x00000000); /* disable all */
- mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xffffc7f5);
- mtdcr(uic1tr, 0x00000000);
- mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(uic1sr, 0xffffffff); /* clear all */
-
- mtdcr(uic2sr, 0xffffffff); /* clear all */
- mtdcr(uic2er, 0x00000000); /* disable all */
- mtdcr(uic2cr, 0x00000000); /* all non-critical */
- mtdcr(uic2pr, 0x27ffffff);
- mtdcr(uic2tr, 0x00000000);
- mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(uic2sr, 0xffffffff); /* clear all */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
+ mtdcr(UIC0PR, 0xfffff7ef);
+ mtdcr(UIC0TR, 0x00000000);
+ mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffc7f5);
+ mtdcr(UIC1TR, 0x00000000);
+ mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+ mtdcr(UIC2ER, 0x00000000); /* disable all */
+ mtdcr(UIC2CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC2PR, 0x27ffffff);
+ mtdcr(UIC2TR, 0x00000000);
+ mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
/* select Ethernet pins */
mfsdr(SDR0_PFC1, sdr0_pfc1);
if (getenv("pciearly") && (!is_monarch())) {
printf("PCI: early target init\n");
- pci_setup_indirect(&hose, PCIX0_CFGADR, PCIX0_CFGDATA);
+ pci_setup_indirect(&hose, PCIL0_CFGADR, PCIL0_CFGDATA);
pci_target_init(&hose);
}
return 0;
gd->bd->bi_flashoffset = 0;
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtdcr(ebccfga, pb2cr);
+ mtdcr(EBC0_CFGADDR, PB2CR);
#else
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
#endif
- pbcr = mfdcr(ebccfgd);
+ pbcr = mfdcr(EBC0_CFGDATA);
size_val = ffs(gd->bd->bi_flashsize) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtdcr(ebccfga, pb2cr);
+ mtdcr(EBC0_CFGADDR, PB2CR);
#else
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
#endif
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/*
* Re-check to get correct base address
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
- mtdcr(plb4_acr, reg);
+ reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
+ mtdcr(PLB4_ACR, reg);
#ifdef CONFIG_FPGA
pmc440_init_fpga();
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
#ifdef CONFIG_PCI_PNP
hose->fixup_irq = pmc440_pci_fixup_irq;
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xc0000001); /* 1G + No prefetching, */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xc0000001); /* 1G + No prefetching, */
/* and enable region */
if (!is_monarch()) {
ptmla_str = getenv("ptm1la");
ptmms_str = getenv("ptm1ms");
if(NULL != ptmla_str && NULL != ptmms_str ) {
- out32r(PCIX0_PTM1MS,
+ out32r(PCIL0_PTM1MS,
simple_strtoul(ptmms_str, NULL, 16));
- out32r(PCIX0_PTM1LA,
+ out32r(PCIL0_PTM1LA,
simple_strtoul(ptmla_str, NULL, 16));
} else {
/* BAR1: default top 64MB of RAM */
- out32r(PCIX0_PTM1MS, 0xfc000001);
- out32r(PCIX0_PTM1LA, 0x0c000000);
+ out32r(PCIL0_PTM1MS, 0xfc000001);
+ out32r(PCIL0_PTM1LA, 0x0c000000);
}
} else {
/* BAR1: default: complete 256MB RAM */
- out32r(PCIX0_PTM1MS, 0xf0000001);
- out32r(PCIX0_PTM1LA, 0x00000000);
+ out32r(PCIL0_PTM1MS, 0xf0000001);
+ out32r(PCIL0_PTM1LA, 0x00000000);
}
ptmla_str = getenv("ptm2la"); /* Local Addr. Reg */
ptmms_str = getenv("ptm2ms"); /* Memory Size/Attribute */
if(NULL != ptmla_str && NULL != ptmms_str ) {
- out32r(PCIX0_PTM2MS, simple_strtoul(ptmms_str, NULL, 16));
- out32r(PCIX0_PTM2LA, simple_strtoul(ptmla_str, NULL, 16));
+ out32r(PCIL0_PTM2MS, simple_strtoul(ptmms_str, NULL, 16));
+ out32r(PCIL0_PTM2LA, simple_strtoul(ptmla_str, NULL, 16));
} else {
/* BAR2: default: 4MB FPGA */
- out32r(PCIX0_PTM2MS, 0xffc00001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0xef000000); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0xffc00001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0xef000000); /* Local Addr. Reg */
}
if (is_monarch()) {
switch (state) {
case 1:
/* Enable write access, clear bit GPIO_SINT2. */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~GPIO0_EP_EEP);
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) & ~GPIO0_EP_EEP);
state = 0;
break;
case 0:
/* Disable write access, set bit GPIO_SINT2. */
- out32(GPIO0_OR, in32(GPIO0_OR) | GPIO0_EP_EEP);
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) | GPIO0_EP_EEP);
state = 0;
break;
default:
/* Read current status back. */
- state = (0 == (in32(GPIO0_OR) & GPIO0_EP_EEP));
+ state = (0 == (in_be32((void *)GPIO0_OR)
+ & GPIO0_EP_EEP));
break;
}
}