/*
+ * (C) Copyright 2009
+ * Matthias Fuchs, esd gmbh, matthias.fuchs@esd.eu
+ *
* (C) Copyright 2006
* Sylvie Gohl, AMCC/IBM, gohl.sylvie@fr.ibm.com
* Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
+#include <asm/mmu.h>
#include <ppc440.h>
extern int denali_wait_for_dlllock(void);
extern void denali_core_search_data_eye(void);
+struct sdram_conf_s {
+ ulong size;
+ int rows;
+ int banks;
+};
-#if defined(CONFIG_NAND_SPL)
-/* Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
- * for the 4k NAND boot image so define bus_frequency to 133MHz here
- * which is save for the refresh counter setup.
- */
-#define get_bus_freq(val) 133000000
-#endif
+struct sdram_conf_s sdram_conf[] = {
+ {(1024 << 20), 14, 8}, /* 1GByte: 4x2GBit, 14x10, 8 banks */
+ {(512 << 20), 13, 8}, /* 512MByte: 4x1GBit, 13x10, 8 banks */
+ {(256 << 20), 13, 4}, /* 256MByte: 4x512MBit, 13x10, 4 banks */
+};
-/*************************************************************************
- *
+/*
* initdram -- 440EPx's DDR controller is a DENALI Core
- *
- ************************************************************************/
-phys_size_t initdram (int board_type)
+ */
+int initdram_by_rb(int rows, int banks)
{
-#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-#if !defined(CONFIG_NAND_SPL)
ulong speed = get_bus_freq(0);
-#else
- ulong speed = 133333333; /* 133MHz is on the safe side */
-#endif
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_07, 0x000D0100);
mtsdram(DDR0_08, 0x02430001);
mtsdram(DDR0_09, 0x00011D5F);
- mtsdram(DDR0_10, 0x00000300);
+ mtsdram(DDR0_10, 0x00000100);
mtsdram(DDR0_11, 0x0027C800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_27, 0x0000682B);
mtsdram(DDR0_28, 0x00000000);
mtsdram(DDR0_31, 0x00000000);
- mtsdram(DDR0_42, 0x01000006);
- mtsdram(DDR0_43, 0x030A0200);
+
+ mtsdram(DDR0_42,
+ DDR0_42_ADDR_PINS_DECODE(14 - rows) |
+ 0x00000006);
+ mtsdram(DDR0_43,
+ DDR0_43_EIGHT_BANK_MODE_ENCODE(8 == banks ? 1 : 0) |
+ 0x030A0200);
+
mtsdram(DDR0_44, 0x00000003);
mtsdram(DDR0_02, 0x00000001);
denali_wait_for_dlllock();
-#endif /* #ifndef CONFIG_NAND_U_BOOT */
#ifdef CONFIG_DDR_DATA_EYE
- /* -----------------------------------------------------------+
+ /*
* Perform data eye search if requested.
- * ----------------------------------------------------------*/
+ */
denali_core_search_data_eye();
#endif
-
/*
* Clear possible errors resulting from data-eye-search.
* If not done, then we could get an interrupt later on when
*/
set_mcsr(get_mcsr());
- return (CONFIG_SYS_MBYTES_SDRAM << 20);
+ return 0;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t size;
+ int n;
+
+ /* go through supported memory configurations */
+ for (n = 0; n < ARRAY_SIZE(sdram_conf); n++) {
+ size = sdram_conf[n].size;
+
+ /* program TLB entries */
+ program_tlb(0, CONFIG_SYS_SDRAM_BASE, size,
+ TLB_WORD2_I_ENABLE);
+
+ /*
+ * setup denali core
+ */
+ initdram_by_rb(sdram_conf[n].rows,
+ sdram_conf[n].banks);
+
+ /* check for suitable configuration */
+ if (get_ram_size(CONFIG_SYS_SDRAM_BASE, size) == size)
+ return size;
+
+ /* delete TLB entries */
+ remove_tlb(CONFIG_SYS_SDRAM_BASE, size);
+ }
+
+ return 0;
}