#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_86xx.h>
-#include <asm/immap_fsl_pci.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
#include <i2c.h>
#include <asm/io.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <spd_sdram.h>
+#include <netdev.h>
#include "../common/pixis.h"
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
void sdram_init(void);
-long int fixed_sdram(void);
+phys_size_t fixed_sdram(void);
void mpc8610hpcd_diu_init(void);
/* called before any console output */
int board_early_init_f(void)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_gur_t *gur = &immap->im_gur;
gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */
int misc_init_r(void)
{
u8 tmp_val, version;
+ u8 *pixis_base = (u8 *)PIXIS_BASE;
/*Do not use 8259PIC*/
- tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0);
- out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x80);
+ tmp_val = in_8(pixis_base + PIXIS_BRDCFG0);
+ out_8(pixis_base + PIXIS_BRDCFG0, tmp_val | 0x80);
/*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/
- version = in8(PIXIS_BASE + PIXIS_PVER);
+ version = in_8(pixis_base + PIXIS_PVER);
if(version >= 0x07) {
- tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0);
- out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val & 0xbf);
+ tmp_val = in_8(pixis_base + PIXIS_BRDCFG0);
+ out_8(pixis_base + PIXIS_BRDCFG0, tmp_val & 0xbf);
}
/* Using this for DIU init before the driver in linux takes over
int checkboard(void)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm;
+ u8 *pixis_base = (u8 *)PIXIS_BASE;
- printf ("Board: MPC8610HPCD, System ID: 0x%02lx, "
- "System Version: 0x%02lx, FPGA Version: 0x%02lx\n",
- in8(PIXIS_BASE + PIXIS_ID), in8(PIXIS_BASE + PIXIS_VER),
- in8(PIXIS_BASE + PIXIS_PVER));
+ printf ("Board: MPC8610HPCD, System ID: 0x%02x, "
+ "System Version: 0x%02x, FPGA Version: 0x%02x\n",
+ in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
+ in_8(pixis_base + PIXIS_PVER));
mcm->abcr |= 0x00010000; /* 0 */
mcm->hpmr3 = 0x80000008; /* 4c */
phys_size_t
initdram(int board_type)
{
- long dram_size = 0;
+ phys_size_t dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
- dram_size = spd_sdram();
+ dram_size = fsl_ddr_sdram();
#else
dram_size = fixed_sdram();
#endif
-#if defined(CFG_RAMBOOT)
- puts(" DDR: ");
- return dram_size;
-#endif
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize and enable DDR ECC.
- */
- ddr_enable_ecc(dram_size);
-#endif
-
puts(" DDR: ");
return dram_size;
}
* Fixed sdram init -- doesn't use serial presence detect.
*/
-long int fixed_sdram(void)
+phys_size_t fixed_sdram(void)
{
-#if !defined(CFG_RAMBOOT)
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
+#if !defined(CONFIG_SYS_RAMBOOT)
+ volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
uint d_init;
ddr->timing_cfg_0 = 0x00260802;
ddr->timing_cfg_1 = 0x3935d322;
ddr->timing_cfg_2 = 0x14904cc8;
- ddr->sdram_mode_1 = 0x00480432;
+ ddr->sdram_mode = 0x00480432;
ddr->sdram_mode_2 = 0x00000000;
ddr->sdram_interval = 0x06180fff; /* 0x06180100; */
ddr->sdram_data_init = 0xDEADBEEF;
udelay(500);
- ddr->sdram_cfg_1 = 0xc3000000; /* 0xe3008000;*/
+ ddr->sdram_cfg = 0xc3000000; /* 0xe3008000;*/
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
return 512 * 1024 * 1024;
#endif
- return CFG_SDRAM_SIZE * 1024 * 1024;
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif
void pci_init_board(void)
{
- volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC8610_PORDEVSR_IO_SEL)
#ifdef CONFIG_PCIE1
{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE1_ADDR;
- extern void fsl_pci_init(struct pci_controller *hose);
+ volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
- int pcie_configured = (io_sel == 1) || (io_sel == 4);
- int pcie_ep = (host_agent == 0) || (host_agent == 2) ||
- (host_agent == 5);
+ int pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
+ int pcie_ep = is_fsl_pci_agent(LAW_TRGT_IF_PCIE_1, host_agent);
+ struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC86xx_DEVDISR_PCIE1)) {
printf(" PCIe 1 connected to Uli as %s (base address %x)\n",
if (pci->pme_msg_det)
pci->pme_msg_det = 0xffffffff;
- /* inbound */
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEMORY_BUS,
- CFG_PCI_MEMORY_PHYS,
- CFG_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY);
-
/* outbound memory */
- pci_set_region(hose->regions + 1,
- CFG_PCIE1_MEM_BASE,
- CFG_PCIE1_MEM_PHYS,
- CFG_PCIE1_MEM_SIZE,
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE1_MEM_BUS,
+ CONFIG_SYS_PCIE1_MEM_PHYS,
+ CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
- pci_set_region(hose->regions + 2,
- CFG_PCIE1_IO_BASE,
- CFG_PCIE1_IO_PHYS,
- CFG_PCIE1_IO_SIZE,
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE1_IO_BUS,
+ CONFIG_SYS_PCIE1_IO_PHYS,
+ CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
- hose->region_count = 3;
+ hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
- pci_setup_indirect(hose, (int)&pci->cfg_addr,
- (int)&pci->cfg_data);
- fsl_pci_init(hose);
+ fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
first_free_busno = hose->last_busno + 1;
printf(" PCI-Express 1 on bus %02x - %02x\n",
#ifdef CONFIG_PCIE2
{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE2_ADDR;
- extern void fsl_pci_init(struct pci_controller *hose);
+ volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
struct pci_controller *hose = &pcie2_hose;
+ struct pci_region *r = hose->regions;
- int pcie_configured = (io_sel == 0) || (io_sel == 4);
- int pcie_ep = (host_agent == 0) || (host_agent == 1) ||
- (host_agent == 4);
+ int pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_2, io_sel);
+ int pcie_ep = is_fsl_pci_agent(LAW_TRGT_IF_PCIE_2, host_agent);
if (pcie_configured && !(devdisr & MPC86xx_DEVDISR_PCIE2)) {
printf(" PCI-Express 2 connected to slot as %s" \
if (pci->pme_msg_det)
pci->pme_msg_det = 0xffffffff;
- /* inbound */
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEMORY_BUS,
- CFG_PCI_MEMORY_PHYS,
- CFG_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY);
-
/* outbound memory */
- pci_set_region(hose->regions + 1,
- CFG_PCIE2_MEM_BASE,
- CFG_PCIE2_MEM_PHYS,
- CFG_PCIE2_MEM_SIZE,
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE2_MEM_BUS,
+ CONFIG_SYS_PCIE2_MEM_PHYS,
+ CONFIG_SYS_PCIE2_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
- pci_set_region(hose->regions + 2,
- CFG_PCIE2_IO_BASE,
- CFG_PCIE2_IO_PHYS,
- CFG_PCIE2_IO_SIZE,
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE2_IO_BUS,
+ CONFIG_SYS_PCIE2_IO_PHYS,
+ CONFIG_SYS_PCIE2_IO_SIZE,
PCI_REGION_IO);
- hose->region_count = 3;
+ hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
- pci_setup_indirect(hose, (int)&pci->cfg_addr,
- (int)&pci->cfg_data);
- fsl_pci_init(hose);
+ fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
first_free_busno = hose->last_busno + 1;
printf(" PCI-Express 2 on bus %02x - %02x\n",
#ifdef CONFIG_PCI1
{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI1_ADDR;
- extern void fsl_pci_init(struct pci_controller *hose);
+ volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
- int pci_agent = (host_agent >= 4) && (host_agent <= 6);
+ int pci_agent = is_fsl_pci_agent(LAW_TRGT_IF_PCI_1, host_agent);
+ struct pci_region *r = hose->regions;
if ( !(devdisr & MPC86xx_DEVDISR_PCI1)) {
printf(" PCI connected to PCI slots as %s" \
pci_agent ? "Agent" : "Host",
(uint)pci);
- /* inbound */
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEMORY_BUS,
- CFG_PCI_MEMORY_PHYS,
- CFG_PCI_MEMORY_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY);
-
/* outbound memory */
- pci_set_region(hose->regions + 1,
- CFG_PCI1_MEM_BASE,
- CFG_PCI1_MEM_PHYS,
- CFG_PCI1_MEM_SIZE,
+ pci_set_region(r++,
+ CONFIG_SYS_PCI1_MEM_BUS,
+ CONFIG_SYS_PCI1_MEM_PHYS,
+ CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
- pci_set_region(hose->regions + 2,
- CFG_PCI1_IO_BASE,
- CFG_PCI1_IO_PHYS,
- CFG_PCI1_IO_SIZE,
+ pci_set_region(r++,
+ CONFIG_SYS_PCI1_IO_BUS,
+ CONFIG_SYS_PCI1_IO_PHYS,
+ CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
- hose->region_count = 3;
+ hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
- pci_setup_indirect(hose, (int) &pci->cfg_addr,
- (int) &pci->cfg_data);
- fsl_pci_init(hose);
+ fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
first_free_busno = hose->last_busno + 1;
printf(" PCI on bus %02x - %02x\n",
void
ft_board_setup(void *blob, bd_t *bd)
{
- int node, tmp[2];
- const char *path;
-
- do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
- "timebase-frequency", bd->bi_busfreq / 4, 1);
- do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
- "bus-frequency", bd->bi_busfreq, 1);
- do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
- "clock-frequency", bd->bi_intfreq, 1);
- do_fixup_by_prop_u32(blob, "device_type", "soc", 4,
- "bus-frequency", bd->bi_busfreq, 1);
-
- do_fixup_by_compat_u32(blob, "ns16550",
- "clock-frequency", bd->bi_busfreq, 1);
-
- fdt_fixup_memory(blob, bd->bi_memstart, bd->bi_memsize);
-
-
- node = fdt_path_offset(blob, "/aliases");
- tmp[0] = 0;
- if (node >= 0) {
+ ft_cpu_setup(blob, bd);
#ifdef CONFIG_PCI1
- path = fdt_getprop(blob, node, "pci0", NULL);
- if (path) {
- tmp[1] = pci1_hose.last_busno - pci1_hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-
+ ft_fsl_pci_setup(blob, "pci0", &pci1_hose);
#endif
#ifdef CONFIG_PCIE1
- path = fdt_getprop(blob, node, "pci1", NULL);
- if (path) {
- tmp[1] = pcie1_hose.last_busno
- - pcie1_hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
+ ft_fsl_pci_setup(blob, "pci1", &pcie1_hose);
#endif
#ifdef CONFIG_PCIE2
- path = fdt_getprop(blob, node, "pci2", NULL);
- if (path) {
- tmp[1] = pcie2_hose.last_busno
- - pcie2_hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
+ ft_fsl_pci_setup(blob, "pci2", &pcie2_hose);
#endif
- }
}
#endif
{
u8 i;
ulong val = 0;
- ulong a;
+ u8 *pixis_base = (u8 *)PIXIS_BASE;
- a = PIXIS_BASE + PIXIS_SPD;
- i = in8(a);
+ i = in_8(pixis_base + PIXIS_SPD);
i &= 0x07;
switch (i) {
return val;
}
+
+int board_eth_init(bd_t *bis)
+{
+ return pci_eth_init(bis);
+}
+
+void board_reset(void)
+{
+ u8 *pixis_base = (u8 *)PIXIS_BASE;
+
+ out_8(pixis_base + PIXIS_RST, 0);
+
+ while (1)
+ ;
+}