#include <common.h>
#include <fsl_esdhc.h>
#include <mmc.h>
+#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ETH_PHY_RESET IMX_GPIO_NR(4, 21)
+
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
+static iomux_v3_cfg_t const fec_pads[] = {
+ MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
+static void setup_iomux_fec(void)
+{
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+
+ /* Reset LAN8720 PHY */
+ gpio_direction_output(ETH_PHY_RESET , 0);
+ udelay(1000);
+ gpio_set_value(ETH_PHY_RESET, 1);
+}
+
static struct fsl_esdhc_cfg usdhc_cfg[1] = {
{USDHC2_BASE_ADDR},
};
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+ int ret;
+
+ setup_iomux_fec();
+
+ ret = cpu_eth_init(bis);
+ if (ret) {
+ printf("FEC MXC: %s:failed\n", __func__);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int setup_fec(void)
+{
+ struct iomuxc_base_regs *iomuxc_regs =
+ (struct iomuxc_base_regs *)IOMUXC_BASE_ADDR;
+ int ret;
+
+ /* clear gpr1[14], gpr1[18:17] to select anatop clock */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
+
+ ret = enable_fec_anatop_clock();
+ if (ret)
+ return ret;
+
+ return 0;
+}
+#endif
+
+
int board_early_init_f(void)
{
setup_iomux_uart();
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+#ifdef CONFIG_FEC_MXC
+ setup_fec();
+#endif
return 0;
}