#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
-#include <asm/imx-common/iomux-v3.h>
-#include <asm/imx-common/boot_mode.h>
-#include <asm/imx-common/mxc_i2c.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/mxc_i2c.h>
#include <asm/io.h>
#include <common.h>
#include <fsl_esdhc.h>
#include <power/pfuze3000_pmic.h>
#include "../common/pfuze.h"
#include <usb.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_SPEED_HIGH | \
PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
+#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+ PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
+
#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
-
#define IOX_SDI IMX_GPIO_NR(5, 10)
#define IOX_STCP IMX_GPIO_NR(5, 7)
#define IOX_SHCP IMX_GPIO_NR(5, 11)
-#define IOX_OE IMX_GPIO_NR(5, 18)
+#define IOX_OE IMX_GPIO_NR(5, 8)
static iomux_v3_cfg_t const iox_pads[] = {
/* IOX_SDI */
static enum qn_func qn_output[8] = {
qn_reset, qn_reset, qn_reset, qn_enable, qn_disable, qn_reset,
- qn_disable, qn_enable
+ qn_disable, qn_disable
};
static void iox74lv_init(void)
* shift register will be output to pins
*/
gpio_direction_output(IOX_STCP, 1);
-
- gpio_direction_output(IOX_OE, 1);
};
#ifdef CONFIG_SYS_I2C_MXC
reg, rev_id);
/* disable Low Power Mode during standby mode */
- pmic_reg_read(pfuze, PFUZE3000_LDOGCTL, ®);
- reg |= 0x1;
- pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, reg);
+ pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, 0x1);
/* SW1B step ramp up time from 2us to 4us/25mV */
reg = 0x40;
MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
+#ifndef CONFIG_SPL_BUILD
static iomux_v3_cfg_t const usdhc1_pads[] = {
MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
/* RST_B */
MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
+#endif
/*
* mx6ul_14x14_evk board default supports sd card. If want to use
MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
-static iomux_v3_cfg_t const usdhc2_cd_pads[] = {
- /*
- * The evk board uses DAT3 to detect CD card plugin,
- * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
- */
- MX6_PAD_NAND_DATA03__GPIO4_IO05 | MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL),
-};
+/*
+ * The evk board uses DAT3 to detect CD card plugin,
+ * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
+ */
+static iomux_v3_cfg_t const usdhc2_cd_pad =
+ MX6_PAD_NAND_DATA03__GPIO4_IO05 | MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL);
-static iomux_v3_cfg_t const usdhc2_dat3_pads[] = {
+static iomux_v3_cfg_t const usdhc2_dat3_pad =
MX6_PAD_NAND_DATA03__USDHC2_DATA3 |
- MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL),
-};
+ MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL);
#endif
static void setup_iomux_uart(void)
#define QSPI_PAD_CTRL1 \
(PAD_CTL_SRE_FAST | PAD_CTL_SPEED_MED | \
- PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_60ohm)
+ PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_120ohm)
static iomux_v3_cfg_t const quadspi_pads[] = {
MX6_PAD_NAND_WP_B__QSPI_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
ret = 1;
#else
- imx_iomux_v3_setup_multiple_pads(usdhc2_cd_pads,
- ARRAY_SIZE(usdhc2_cd_pads));
+ imx_iomux_v3_setup_pad(usdhc2_cd_pad);
gpio_direction_input(USDHC2_CD_GPIO);
/*
*/
ret = gpio_get_value(USDHC2_CD_GPIO);
- imx_iomux_v3_setup_multiple_pads(usdhc2_dat3_pads,
- ARRAY_SIZE(usdhc2_dat3_pads));
+ imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
#endif
break;
}
/*
* According to the board_mmc_init() the following map is done:
- * (U-boot device node) (Physical Port)
+ * (U-Boot device node) (Physical Port)
* mmc0 USDHC1
* mmc1 USDHC2
*/
}
#endif
+#ifdef CONFIG_VIDEO_MXS
+static iomux_v3_cfg_t const lcd_pads[] = {
+ MX6_PAD_LCD_CLK__LCDIF_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_ENABLE__LCDIF_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_HSYNC__LCDIF_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_VSYNC__LCDIF_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA00__LCDIF_DATA00 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA01__LCDIF_DATA01 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA02__LCDIF_DATA02 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA03__LCDIF_DATA03 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA04__LCDIF_DATA04 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA05__LCDIF_DATA05 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA06__LCDIF_DATA06 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA07__LCDIF_DATA07 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA08__LCDIF_DATA08 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA09__LCDIF_DATA09 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA10__LCDIF_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA11__LCDIF_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA12__LCDIF_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA13__LCDIF_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA14__LCDIF_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA15__LCDIF_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA16__LCDIF_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA17__LCDIF_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA18__LCDIF_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA19__LCDIF_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA20__LCDIF_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA21__LCDIF_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA22__LCDIF_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+ MX6_PAD_LCD_DATA23__LCDIF_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+
+ /* LCD_RST */
+ MX6_PAD_SNVS_TAMPER9__GPIO5_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+
+ /* Use GPIO for Brightness adjustment, duty cycle = period. */
+ MX6_PAD_GPIO1_IO08__GPIO1_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static int setup_lcd(void)
+{
+ enable_lcdif_clock(LCDIF1_BASE_ADDR, 1);
+
+ imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+ /* Reset the LCD */
+ gpio_direction_output(IMX_GPIO_NR(5, 9) , 0);
+ udelay(500);
+ gpio_direction_output(IMX_GPIO_NR(5, 9) , 1);
+
+ /* Set Brightness to high */
+ gpio_direction_output(IMX_GPIO_NR(1, 8) , 1);
+
+ return 0;
+}
+#endif
+
int board_early_init_f(void)
{
setup_iomux_uart();
board_qspi_init();
#endif
+#ifdef CONFIG_VIDEO_MXS
+ setup_lcd();
+#endif
+
return 0;
}
#endif
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- setenv("board_name", "EVK");
+ env_set("board_name", "EVK");
if (is_mx6ul_9x9_evk())
- setenv("board_rev", "9X9");
+ env_set("board_rev", "9X9");
else
- setenv("board_rev", "14X14");
+ env_set("board_rev", "14X14");
#endif
return 0;
.sde_to_rst = 0, /* LPDDR2 does not need this field */
.rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
.ddr_type = DDR_TYPE_LPDDR2,
+ .refsel = 0, /* Refresh cycles at 64KHz */
+ .refr = 3, /* 4 refresh commands per refresh cycle */
};
#else
.dram_odt0 = 0x00000030,
.dram_odt1 = 0x00000030,
.dram_sdba2 = 0x00000000,
- .dram_sdclk_0 = 0x00000008,
- .dram_sdqs0 = 0x00000038,
+ .dram_sdclk_0 = 0x00000030,
+ .dram_sdqs0 = 0x00000030,
.dram_sdqs1 = 0x00000030,
.dram_reset = 0x00000030,
};
static struct mx6_mmdc_calibration mx6_mmcd_calib = {
- .p0_mpwldectrl0 = 0x00070007,
- .p0_mpdgctrl0 = 0x41490145,
- .p0_mprddlctl = 0x40404546,
- .p0_mpwrdlctl = 0x4040524D,
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpdgctrl0 = 0x41570155,
+ .p0_mprddlctl = 0x4040474A,
+ .p0_mpwrdlctl = 0x40405550,
};
struct mx6_ddr_sysinfo ddr_sysinfo = {
.cs1_mirror = 0,
.rtt_wr = 2,
.rtt_nom = 1, /* RTT_Nom = RZQ/2 */
- .walat = 1, /* Write additional latency */
+ .walat = 0, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.ddr_type = DDR_TYPE_DDR3,
+ .refsel = 0, /* Refresh cycles at 64KHz */
+ .refr = 1, /* 2 refresh commands per refresh cycle */
};
static struct mx6_ddr3_cfg mem_ddr = {
void board_init_f(ulong dummy)
{
+ ccgr_init();
+
/* setup AIPS and disable watchdog */
arch_cpu_init();
- ccgr_init();
-
/* iomux and setup of i2c */
board_early_init_f();
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
-
-void reset_cpu(ulong addr)
-{
-}
#endif
projects / u-boot / blobdiff