(and variants). Variants inclued T1042 presonality of T1040, in which
case T1040RDB can also be called T1042RDB.
+The T1042RDB is a Freescale reference board that hosts the T1042 SoC
+(and variants). The board is similar to T1040RDB, T1040 is a reduced
+personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
+
+The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC.
+(a personality of T1040 SoC). The board is similar to T1040RDB but is
+designed specially with low power features targeted for Printing Image Market.
+
+Basic difference's among T1040RDB, T1042RDB_PI, T1042RDB
+-------------------------------------------------------------------------
+Board Si Protocol Targeted Market
+-------------------------------------------------------------------------
+T1040RDB T1040 0x66 Networking
+T1040RDB T1042 0x86 Networking
+T1042RDB_PI T1042 0x06 Printing & Imaging
+
+
T1040 SoC Overview
------------------
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
- Two Serial ports
- Four I2C ports
+T1042RDB_PI board Overview
+-------------------------
+ - SERDES Connections, 8 lanes information:
+ 1, 2, 3, 4 : PCIe x4 slot
+ 5: mini PCIe connector
+ 6: mini PCIe connector
+ 7: NA
+ 8: SATA connector
+ - DDR Controller
+ - Supports rates of up to 1600 MHz data-rate
+ - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
+ - IFC/Local Bus
+ - NAND flash: 1GB 8-bit NAND flash
+ - NOR: 128MB 16-bit NOR Flash
+ - Ethernet
+ - Two on-board RGMII 10/100/1G ethernet ports.
+ - CPLD
+ - Clocks
+ - System and DDR clock (SYSCLK, “DDRCLK”)
+ - SERDES clocks
+ - Video
+ - DIU supports video at up to 1280x1024x32bpp
+ - Power Supplies
+ - USB
+ - Supports two USB 2.0 ports with integrated PHYs
+ - Two type A ports with 5V@1.5A per port.
+ - SDHC
+ - SDHC/SDXC connector
+ - SPI
+ - On-board 64MB SPI flash
+ - Other IO
+ - Two Serial ports
+ - Four I2C ports
+
Memory map
-----------
The addresses in brackets are physical addresses.
NOR Flash memory Map
---------------------
Start End Definition Size
-0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB
-0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB
-0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB
-0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB
-0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB
+0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
+0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
+0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
+0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
+0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
-0xEBF80000 0xEBFFFFFF u-boot (alt bank) 512KB
-0xEBF60000 0xEBF7FFFF u-boot env (alt bank) 128KB
-0xEBF40000 0xEBF5FFFF FMAN ucode (alt bank) 128KB
-0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB
+0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
+0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
+0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
+0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB
0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
0xE8000000 0xE801FFFF RCW (current bank) 128KB
Commands for switching to alternate bank.
1. To change from vbank0 to vbank4
- => qixis_reset altbank (it will boot using vbank4)
+ => cpld reset altbank (it will boot using vbank4)
2.To change from vbank4 to vbank0
- => qixis reset (it will boot using vbank0)
+ => cpld reset (it will boot using vbank0)
+
+NAND boot with 2 Stage boot loader
+----------------------------------
+PBL initialise the internal SRAM and copy SPL(160KB) in SRAM.
+SPL further initialise DDR using SPD and environment variables and copy
+u-boot(768 KB) from flash to DDR.
+Finally SPL transer control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+ Run time view of SPL framework during boot :-
+ -----------------------------------------------
+ Area | Address |
+-----------------------------------------------
+ Secure boot | 0xFFFC0000 (32KB) |
+ headers | |
+ -----------------------------------------------
+ GD, BD | 0xFFFC8000 (4KB) |
+ -----------------------------------------------
+ ENV | 0xFFFC9000 (8KB) |
+ -----------------------------------------------
+ HEAP | 0xFFFCB000 (30KB) |
+ -----------------------------------------------
+ STACK | 0xFFFD8000 (22KB) |
+ -----------------------------------------------
+ U-boot SPL | 0xFFFD8000 (160KB) |
+ -----------------------------------------------
+
+NAND Flash memory Map on T104xRDB
+------------------------------------------
+ Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB
+0x180000 0x19FFFF u-boot env 128KB
+0x280000 0x29FFFF FMAN Ucode 128KB
+0x380000 0x39FFFF QE Firmware 128KB
+
+SD Card memory Map on T104xRDB
+------------------------------------------
+ Block #blocks Definition Size
+0x008 2048 u-boot 1MB
+0x800 0024 u-boot env 8KB
+0x820 0256 FMAN Ucode 128KB
+0x920 0256 QE Firmware 128KB
+
+SPI Flash memory Map on T104xRDB
+------------------------------------------
+ Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x12FFFF FMAN Ucode 128KB
+0x130000 0x14FFFF QE Firmware 128KB
+
+Please note QE Firmware is only valid for T1040RDB
+
+
+Switch Settings: (ON is 0, OFF is 1)
+===============
+NAND boot SW setting:
+SW1: 10001000
+SW2: 00111011
+SW3: 11110001
+
+SPI boot SW setting:
+SW1: 00100010
+SW2: 10111011
+SW3: 11100001
+
+SD boot SW setting:
+SW1: 00100000
+SW2: 00111011
+SW3: 11100001
projects / u-boot / blobdiff