*/
#include <common.h>
+#if defined(CONFIG_KM82XX)
#include <mpc8260.h>
+#endif
#include <ioports.h>
+#include <command.h>
#include <malloc.h>
+#include <hush.h>
+#include <net.h>
+#include <netdev.h>
+#include <asm/io.h>
#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
#endif
+#include "../common/common.h"
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
#include <i2c.h>
-#endif
-extern int i2c_soft_read_pin (void);
+static void i2c_write_start_seq(void);
+static int i2c_make_abort(void);
+DECLARE_GLOBAL_DATA_PTR;
-#if defined(CFG_I2C_INIT_BOARD)
-#define DELAY_ABORT_SEQ 62
-#define DELAY_HALF_PERIOD (500 / (CFG_I2C_SPEED / 1000))
+int ivm_calc_crc(unsigned char *buf, int len)
+{
+ const unsigned short crc_tab[16] = {
+ 0x0000, 0xCC01, 0xD801, 0x1400,
+ 0xF001, 0x3C00, 0x2800, 0xE401,
+ 0xA001, 0x6C00, 0x7800, 0xB401,
+ 0x5000, 0x9C01, 0x8801, 0x4400};
-#if defined(CONFIG_MGCOGE)
-#define SDA_MASK 0x00010000
-#define SCL_MASK 0x00020000
-static void set_pin (int state, unsigned long mask)
+ unsigned short crc = 0; /* final result */
+ unsigned short r1 = 0; /* temp */
+ unsigned char byte = 0; /* input buffer */
+ int i;
+
+ /* calculate CRC from array data */
+ for (i = 0; i < len; i++) {
+ byte = buf[i];
+
+ /* lower 4 bits */
+ r1 = crc_tab[crc & 0xF];
+ crc = ((crc) >> 4) & 0x0FFF;
+ crc = crc ^ r1 ^ crc_tab[byte & 0xF];
+
+ /* upper 4 bits */
+ r1 = crc_tab[crc & 0xF];
+ crc = (crc >> 4) & 0x0FFF;
+ crc = crc ^ r1 ^ crc_tab[(byte >> 4) & 0xF];
+ }
+ return crc;
+}
+
+/*
+ * Set Keymile specific environment variables
+ * Currently only some memory layout variables are calculated here
+ * ... ------------------------------------------------
+ * ... |@rootfsaddr |@pnvramaddr |@varaddr |@reserved |@END_OF_RAM
+ * ... |<------------------- pram ------------------->|
+ * ... ------------------------------------------------
+ * @END_OF_RAM: denotes the RAM size
+ * @pnvramaddr: Startadress of pseudo non volatile RAM in hex
+ * @pram : preserved ram size in k
+ * @varaddr : startadress for /var mounted into RAM
+ */
+int set_km_env(void)
{
- volatile ioport_t *iop = ioport_addr ((immap_t *)CFG_IMMR, 3);
+ uchar buf[32];
+ unsigned int pnvramaddr;
+ unsigned int pram;
+ unsigned int varaddr;
- if (state)
- iop->pdat |= (mask);
- else
- iop->pdat &= ~(mask);
+ pnvramaddr = gd->ram_size - CONFIG_KM_RESERVED_PRAM - CONFIG_KM_PHRAM
+ - CONFIG_KM_PNVRAM;
+ sprintf((char *)buf, "0x%x", pnvramaddr);
+ setenv("pnvramaddr", (char *)buf);
- iop->pdir |= (mask);
+ pram = (CONFIG_KM_RESERVED_PRAM + CONFIG_KM_PHRAM + CONFIG_KM_PNVRAM) /
+ 0x400;
+ sprintf((char *)buf, "0x%x", pram);
+ setenv("pram", (char *)buf);
+
+ varaddr = gd->ram_size - CONFIG_KM_RESERVED_PRAM - CONFIG_KM_PHRAM;
+ sprintf((char *)buf, "0x%x", varaddr);
+ setenv("varaddr", (char *)buf);
+ return 0;
}
-static int get_pin (unsigned long mask)
+static int ivm_set_value(char *name, char *value)
{
- volatile ioport_t *iop = ioport_addr ((immap_t *)CFG_IMMR, 3);
+ char tempbuf[256];
- iop->pdir &= ~(mask);
- return (0 != (iop->pdat & (mask)));
+ if (value != NULL) {
+ sprintf(tempbuf, "%s=%s", name, value);
+ return set_local_var(tempbuf, 0);
+ } else {
+ unset_local_var(name);
+ }
+ return 0;
}
-static void set_sda (int state)
+static int ivm_get_value(unsigned char *buf, int len, char *name, int off,
+ int check)
{
- set_pin (state, SDA_MASK);
+ unsigned short val;
+ unsigned char valbuf[30];
+
+ if ((buf[off + 0] != buf[off + 2]) &&
+ (buf[off + 2] != buf[off + 4])) {
+ printf("%s Error corrupted %s\n", __func__, name);
+ val = -1;
+ } else {
+ val = buf[off + 0] + (buf[off + 1] << 8);
+ if ((val == 0) && (check == 1))
+ val = -1;
+ }
+ sprintf((char *)valbuf, "%x", val);
+ ivm_set_value(name, (char *)valbuf);
+ return val;
}
-static void set_scl (int state)
+#define INV_BLOCKSIZE 0x100
+#define INV_DATAADDRESS 0x21
+#define INVENTORYDATASIZE (INV_BLOCKSIZE - INV_DATAADDRESS - 3)
+
+#define IVM_POS_SHORT_TEXT 0
+#define IVM_POS_MANU_ID 1
+#define IVM_POS_MANU_SERIAL 2
+#define IVM_POS_PART_NUMBER 3
+#define IVM_POS_BUILD_STATE 4
+#define IVM_POS_SUPPLIER_PART_NUMBER 5
+#define IVM_POS_DELIVERY_DATE 6
+#define IVM_POS_SUPPLIER_BUILD_STATE 7
+#define IVM_POS_CUSTOMER_ID 8
+#define IVM_POS_CUSTOMER_PROD_ID 9
+#define IVM_POS_HISTORY 10
+#define IVM_POS_SYMBOL_ONLY 11
+
+static char convert_char(char c)
{
- set_pin (state, SCL_MASK);
+ return (c < ' ' || c > '~') ? '.' : c;
}
-static int get_sda (void)
+static int ivm_findinventorystring(int type,
+ unsigned char* const string,
+ unsigned long maxlen,
+ unsigned char *buf)
{
- return get_pin (SDA_MASK);
+ int xcode = 0;
+ unsigned long cr = 0;
+ unsigned long addr = INV_DATAADDRESS;
+ unsigned long size = 0;
+ unsigned long nr = type;
+ int stop = 0; /* stop on semicolon */
+
+ memset(string, '\0', maxlen);
+ switch (type) {
+ case IVM_POS_SYMBOL_ONLY:
+ nr = 0;
+ stop= 1;
+ break;
+ default:
+ nr = type;
+ stop = 0;
+ }
+
+ /* Look for the requested number of CR. */
+ while ((cr != nr) && (addr < INVENTORYDATASIZE)) {
+ if ((buf[addr] == '\r')) {
+ cr++;
+ }
+ addr++;
+ }
+
+ /*
+ * the expected number of CR was found until the end of the IVM
+ * content --> fill string
+ */
+ if (addr < INVENTORYDATASIZE) {
+ /* Copy the IVM string in the corresponding string */
+ for (; (buf[addr] != '\r') &&
+ ((buf[addr] != ';') || (!stop)) &&
+ (size < (maxlen - 1) &&
+ (addr < INVENTORYDATASIZE)); addr++)
+ {
+ size += sprintf((char *)string + size, "%c",
+ convert_char (buf[addr]));
+ }
+
+ /*
+ * copy phase is done: check if everything is ok. If not,
+ * the inventory data is most probably corrupted: tell
+ * the world there is a problem!
+ */
+ if (addr == INVENTORYDATASIZE) {
+ xcode = -1;
+ printf("Error end of string not found\n");
+ } else if ((size >= (maxlen - 1)) &&
+ (buf[addr] != '\r')) {
+ xcode = -1;
+ printf("string too long till next CR\n");
+ }
+ } else {
+ /*
+ * some CR are missing...
+ * the inventory data is most probably corrupted
+ */
+ xcode = -1;
+ printf("not enough cr found\n");
+ }
+ return xcode;
}
-static int get_scl (void)
+#define GET_STRING(name, which, len) \
+ if (ivm_findinventorystring(which, valbuf, len, buf) == 0) { \
+ ivm_set_value(name, (char *)valbuf); \
+ }
+
+static int ivm_check_crc(unsigned char *buf, int block)
{
- return get_pin (SCL_MASK);
+ unsigned long crc;
+ unsigned long crceeprom;
+
+ crc = ivm_calc_crc(buf, CONFIG_SYS_IVM_EEPROM_PAGE_LEN - 2);
+ crceeprom = (buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN - 1] + \
+ buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN - 2] * 256);
+ if (crc != crceeprom) {
+ if (block == 0)
+ printf("Error CRC Block: %d EEprom: calculated: \
+ %lx EEprom: %lx\n", block, crc, crceeprom);
+ return -1;
+ }
+ return 0;
}
-#if defined(CONFIG_HARD_I2C)
-static void setports (int gpio)
+static int ivm_analyze_block2(unsigned char *buf, int len)
{
- volatile ioport_t *iop = ioport_addr ((immap_t *)CFG_IMMR, 3);
+ unsigned char valbuf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN];
+ unsigned long count;
- if (gpio) {
- iop->ppar &= ~(SDA_MASK | SCL_MASK);
- iop->podr &= ~(SDA_MASK | SCL_MASK);
+ /* IVM_MacAddress */
+ sprintf((char *)valbuf, "%pM", buf);
+ ivm_set_value("IVM_MacAddress", (char *)valbuf);
+ /* if an offset is defined, add it */
+#if defined(CONFIG_PIGGY_MAC_ADRESS_OFFSET)
+ if (CONFIG_PIGGY_MAC_ADRESS_OFFSET > 0) {
+ unsigned long val = (buf[4] << 16) + (buf[5] << 8) + buf[6];
+
+ val += CONFIG_PIGGY_MAC_ADRESS_OFFSET;
+ buf[4] = (val >> 16) & 0xff;
+ buf[5] = (val >> 8) & 0xff;
+ buf[6] = val & 0xff;
+ sprintf((char *)valbuf, "%pM", buf);
+ }
+#endif
+ if (getenv("ethaddr") == NULL)
+ setenv((char *)"ethaddr", (char *)valbuf);
+
+ /* IVM_MacCount */
+ count = (buf[10] << 24) +
+ (buf[11] << 16) +
+ (buf[12] << 8) +
+ buf[13];
+ if (count == 0xffffffff)
+ count = 1;
+ sprintf((char *)valbuf, "%lx", count);
+ ivm_set_value("IVM_MacCount", (char *)valbuf);
+ return 0;
+}
+
+int ivm_analyze_eeprom(unsigned char *buf, int len)
+{
+ unsigned short val;
+ unsigned char valbuf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN];
+ unsigned char *tmp;
+
+ if (ivm_check_crc(buf, 0) != 0)
+ return -1;
+
+ ivm_get_value(buf, CONFIG_SYS_IVM_EEPROM_PAGE_LEN,
+ "IVM_BoardId", 0, 1);
+ val = ivm_get_value(buf, CONFIG_SYS_IVM_EEPROM_PAGE_LEN,
+ "IVM_HWKey", 6, 1);
+ if (val != 0xffff) {
+ sprintf((char *)valbuf, "%x", ((val / 100) % 10));
+ ivm_set_value("IVM_HWVariant", (char *)valbuf);
+ sprintf((char *)valbuf, "%x", (val % 100));
+ ivm_set_value("IVM_HWVersion", (char *)valbuf);
+ }
+ ivm_get_value(buf, CONFIG_SYS_IVM_EEPROM_PAGE_LEN,
+ "IVM_Functions", 12, 0);
+
+ GET_STRING("IVM_Symbol", IVM_POS_SYMBOL_ONLY, 8)
+ GET_STRING("IVM_DeviceName", IVM_POS_SHORT_TEXT, 64)
+ tmp = (unsigned char *) getenv("IVM_DeviceName");
+ if (tmp) {
+ int len = strlen((char *)tmp);
+ int i = 0;
+
+ while (i < len) {
+ if (tmp[i] == ';') {
+ ivm_set_value("IVM_ShortText",
+ (char *)&tmp[i + 1]);
+ break;
+ }
+ i++;
+ }
+ if (i >= len)
+ ivm_set_value("IVM_ShortText", NULL);
} else {
- iop->ppar |= (SDA_MASK | SCL_MASK);
- iop->pdir &= ~(SDA_MASK | SCL_MASK);
- iop->podr |= (SDA_MASK | SCL_MASK);
+ ivm_set_value("IVM_ShortText", NULL);
}
+ GET_STRING("IVM_ManufacturerID", IVM_POS_MANU_ID, 32)
+ GET_STRING("IVM_ManufacturerSerialNumber", IVM_POS_MANU_SERIAL, 20)
+ GET_STRING("IVM_ManufacturerPartNumber", IVM_POS_PART_NUMBER, 32)
+ GET_STRING("IVM_ManufacturerBuildState", IVM_POS_BUILD_STATE, 32)
+ GET_STRING("IVM_SupplierPartNumber", IVM_POS_SUPPLIER_PART_NUMBER, 32)
+ GET_STRING("IVM_DelieveryDate", IVM_POS_DELIVERY_DATE, 32)
+ GET_STRING("IVM_SupplierBuildState", IVM_POS_SUPPLIER_BUILD_STATE, 32)
+ GET_STRING("IVM_CustomerID", IVM_POS_CUSTOMER_ID, 32)
+ GET_STRING("IVM_CustomerProductID", IVM_POS_CUSTOMER_PROD_ID, 32)
+
+ if (ivm_check_crc(&buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN * 2], 2) != 0)
+ return 0;
+ ivm_analyze_block2(&buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN * 2],
+ CONFIG_SYS_IVM_EEPROM_PAGE_LEN);
+
+ return 0;
}
+
+int ivm_read_eeprom(void)
+{
+#if defined(CONFIG_I2C_MUX)
+ I2C_MUX_DEVICE *dev = NULL;
#endif
+ uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
+ uchar *buf;
+ unsigned dev_addr = CONFIG_SYS_IVM_EEPROM_ADR;
+ int ret;
+
+#if defined(CONFIG_I2C_MUX)
+ /* First init the Bus, select the Bus */
+#if defined(CONFIG_SYS_I2C_IVM_BUS)
+ dev = i2c_mux_ident_muxstring((uchar *)CONFIG_SYS_I2C_IVM_BUS);
+#else
+ buf = (unsigned char *) getenv("EEprom_ivm");
+ if (buf != NULL)
+ dev = i2c_mux_ident_muxstring(buf);
+#endif
+ if (dev == NULL) {
+ printf("Error couldnt add Bus for IVM\n");
+ return -1;
+ }
+ i2c_set_bus_num(dev->busid);
#endif
-#if defined(CONFIG_MGSUVD)
-static void set_sda (int state)
+ buf = (unsigned char *) getenv("EEprom_ivm_addr");
+ if (buf != NULL)
+ dev_addr = simple_strtoul((char *)buf, NULL, 16);
+
+ /* add deblocking here */
+ i2c_make_abort();
+
+ ret = i2c_read(dev_addr, 0, 1, i2c_buffer,
+ CONFIG_SYS_IVM_EEPROM_MAX_LEN);
+ if (ret != 0) {
+ printf ("Error reading EEprom\n");
+ return -2;
+ }
+
+ return ivm_analyze_eeprom(i2c_buffer, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
+}
+
+#if defined(CONFIG_SYS_I2C_INIT_BOARD)
+#define DELAY_ABORT_SEQ 62 /* @200kHz 9 clocks = 44us, 62us is ok */
+#define DELAY_HALF_PERIOD (500 / (CONFIG_SYS_I2C_SPEED / 1000))
+
+#if defined(CONFIG_KM_82XX)
+#define SDA_MASK 0x00010000
+#define SCL_MASK 0x00020000
+void set_pin(int state, unsigned long mask)
{
- I2C_SDA(state);
+ ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
+
+ if (state)
+ setbits_be32(&iop->pdat, mask);
+ else
+ clrbits_be32(&iop->pdat, mask);
+
+ setbits_be32(&iop->pdir, mask);
}
-static void set_scl (int state)
+static int get_pin(unsigned long mask)
{
- I2C_SCL(state);
+ ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
+
+ clrbits_be32(&iop->pdir, mask);
+ return 0 != (in_be32(&iop->pdat) & mask);
}
-static int get_sda (void)
+static void set_sda(int state)
{
- return i2c_soft_read_pin ();
+ set_pin(state, SDA_MASK);
}
-static int get_scl (void)
+static void set_scl(int state)
{
- int val;
+ set_pin(state, SCL_MASK);
+}
- *(unsigned short *)(I2C_BASE_DIR) &= ~SCL_CONF;
- udelay (1);
- val = *(unsigned char *)(I2C_BASE_PORT);
+static int get_sda(void)
+{
+ return get_pin(SDA_MASK);
+}
- return ((val & SCL_BIT) == SCL_BIT);
+static int get_scl(void)
+{
+ return get_pin(SCL_MASK);
}
+#if defined(CONFIG_HARD_I2C)
+static void setports(int gpio)
+{
+ ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
+
+ if (gpio) {
+ clrbits_be32(&iop->ppar, (SDA_MASK | SCL_MASK));
+ clrbits_be32(&iop->podr, (SDA_MASK | SCL_MASK));
+ } else {
+ setbits_be32(&iop->ppar, (SDA_MASK | SCL_MASK));
+ clrbits_be32(&iop->pdir, (SDA_MASK | SCL_MASK));
+ setbits_be32(&iop->podr, (SDA_MASK | SCL_MASK));
+ }
+}
+#endif
#endif
-static void writeStartSeq (void)
+#if !defined(CONFIG_MPC83xx)
+static void i2c_write_start_seq(void)
{
- set_sda (1);
- udelay (DELAY_HALF_PERIOD);
- set_scl (1);
- udelay (DELAY_HALF_PERIOD);
- set_sda (0);
- udelay (DELAY_HALF_PERIOD);
- set_scl (0);
- udelay (DELAY_HALF_PERIOD);
+ set_sda(1);
+ udelay(DELAY_HALF_PERIOD);
+ set_scl(1);
+ udelay(DELAY_HALF_PERIOD);
+ set_sda(0);
+ udelay(DELAY_HALF_PERIOD);
+ set_scl(0);
+ udelay(DELAY_HALF_PERIOD);
}
-/* I2C is a synchronous protocol and resets of the processor in the middle
- of an access can block the I2C Bus until a powerdown of the full unit is
- done. This function toggles the SCL until the SCL and SCA line are
- released, but max. 16 times, after this a I2C start-sequence is sent.
- This I2C Deblocking mechanism was developed by Keymile in association
- with Anatech and Atmel in 1998.
+/*
+ * I2C is a synchronous protocol and resets of the processor in the middle
+ * of an access can block the I2C Bus until a powerdown of the full unit is
+ * done. This function toggles the SCL until the SCL and SCA line are
+ * released, but max. 16 times, after this a I2C start-sequence is sent.
+ * This I2C Deblocking mechanism was developed by Keymile in association
+ * with Anatech and Atmel in 1998.
*/
-static int i2c_make_abort (void)
+static int i2c_make_abort(void)
{
+
+#if defined(CONFIG_HARD_I2C) && !defined(MACH_TYPE_KM_KIRKWOOD)
+ immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
+ i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
+
+ /*
+ * disable I2C controller first, otherwhise it thinks we want to
+ * talk to the slave port...
+ */
+ clrbits_8(&i2c->i2c_i2mod, 0x01);
+
+ /* Set the PortPins to GPIO */
+ setports(1);
+#endif
+
int scl_state = 0;
int sda_state = 0;
int i = 0;
int ret = 0;
- if (!get_sda ()) {
+ if (!get_sda()) {
ret = -1;
while (i < 16) {
i++;
- set_scl (0);
- udelay (DELAY_ABORT_SEQ);
- set_scl (1);
- udelay (DELAY_ABORT_SEQ);
- scl_state = get_scl ();
- sda_state = get_sda ();
+ set_scl(0);
+ udelay(DELAY_ABORT_SEQ);
+ set_scl(1);
+ udelay(DELAY_ABORT_SEQ);
+ scl_state = get_scl();
+ sda_state = get_sda();
if (scl_state && sda_state) {
ret = 0;
break;
}
}
}
- if (ret == 0) {
- for (i =0; i < 5; i++) {
- writeStartSeq ();
- }
+ if (ret == 0)
+ for (i = 0; i < 5; i++)
+ i2c_write_start_seq();
+
+ /* respect stop setup time */
+ udelay(DELAY_ABORT_SEQ);
+ set_scl(1);
+ udelay(DELAY_ABORT_SEQ);
+ set_sda(1);
+ get_sda();
+
+#if defined(CONFIG_HARD_I2C)
+ /* Set the PortPins back to use for I2C */
+ setports(0);
+#endif
+ return ret;
+}
+#endif
+
+#if defined(CONFIG_MPC83xx)
+static void i2c_write_start_seq(void)
+{
+ struct fsl_i2c *dev;
+ dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
+ udelay(DELAY_ABORT_SEQ);
+ out_8(&dev->cr, (I2C_CR_MEN | I2C_CR_MSTA));
+ udelay(DELAY_ABORT_SEQ);
+ out_8(&dev->cr, (I2C_CR_MEN));
+}
+
+static int i2c_make_abort(void)
+{
+ struct fsl_i2c *dev;
+ dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
+ uchar dummy;
+ uchar last;
+ int nbr_read = 0;
+ int i = 0;
+ int ret = 0;
+
+ /* wait after each operation to finsh with a delay */
+ out_8(&dev->cr, (I2C_CR_MSTA));
+ udelay(DELAY_ABORT_SEQ);
+ out_8(&dev->cr, (I2C_CR_MEN | I2C_CR_MSTA));
+ udelay(DELAY_ABORT_SEQ);
+ dummy = in_8(&dev->dr);
+ udelay(DELAY_ABORT_SEQ);
+ last = in_8(&dev->dr);
+ nbr_read++;
+
+ /*
+ * do read until the last bit is 1, but stop if the full eeprom is
+ * read.
+ */
+ while (((last & 0x01) != 0x01) &&
+ (nbr_read < CONFIG_SYS_IVM_EEPROM_MAX_LEN)) {
+ udelay(DELAY_ABORT_SEQ);
+ last = in_8(&dev->dr);
+ nbr_read++;
}
- get_sda ();
+ if ((last & 0x01) != 0x01)
+ ret = -2;
+ if ((last != 0xff) || (nbr_read > 1))
+ printf("[INFO] i2c abort after %d bytes (0x%02x)\n",
+ nbr_read, last);
+ udelay(DELAY_ABORT_SEQ);
+ out_8(&dev->cr, (I2C_CR_MEN));
+ udelay(DELAY_ABORT_SEQ);
+ /* clear status reg */
+ out_8(&dev->sr, 0);
+
+ for (i = 0; i < 5; i++)
+ i2c_write_start_seq();
+ if (ret != 0)
+ printf("[ERROR] i2c abort failed after %d bytes (0x%02x)\n",
+ nbr_read, last);
+
return ret;
}
+#endif
/**
* i2c_init_board - reset i2c bus. When the board is powercycled during a
*/
void i2c_init_board(void)
{
-#if defined(CONFIG_HARD_I2C)
- volatile immap_t *immap = (immap_t *)CFG_IMMR ;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
+ /* Now run the AbortSequence() */
+ i2c_make_abort();
+}
+#endif
+#endif
- /* disable I2C controller first, otherwhise it thinks we want to */
- /* talk to the slave port... */
- i2c->i2c_i2mod &= ~0x01;
+#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
+int fdt_set_node_and_value(void *blob,
+ char *nodename,
+ char *regname,
+ void *var,
+ int size)
+{
+ int ret = 0;
+ int nodeoffset = 0;
- /* Set the PortPins to GPIO */
- setports (1);
-#endif
+ nodeoffset = fdt_path_offset(blob, nodename);
+ if (nodeoffset >= 0) {
+ ret = fdt_setprop(blob, nodeoffset, regname, var,
+ size);
+ if (ret < 0)
+ printf("ft_blob_update(): cannot set %s/%s "
+ "property err:%s\n", nodename, regname,
+ fdt_strerror(ret));
+ } else {
+ printf("ft_blob_update(): cannot find %s node "
+ "err:%s\n", nodename, fdt_strerror(nodeoffset));
+ }
+ return ret;
+}
- /* Now run the AbortSequence() */
- i2c_make_abort ();
+int fdt_get_node_and_value(void *blob,
+ char *nodename,
+ char *propname,
+ void **var)
+{
+ int len;
+ int nodeoffset = 0;
-#if defined(CONFIG_HARD_I2C)
- /* Set the PortPins back to use for I2C */
- setports (0);
+ nodeoffset = fdt_path_offset(blob, nodename);
+ if (nodeoffset >= 0) {
+ *var = (void *)fdt_getprop(blob, nodeoffset, propname, &len);
+ if (len == 0) {
+ /* no value */
+ printf("%s no value\n", __func__);
+ return -1;
+ } else if (len > 0) {
+ return len;
+ } else {
+ printf("libfdt fdt_getprop(): %s\n",
+ fdt_strerror(len));
+ return -2;
+ }
+ } else {
+ printf("%s: cannot find %s node err:%s\n", __func__,
+ nodename, fdt_strerror(nodeoffset));
+ return -3;
+ }
+}
#endif
+
+#if !defined(MACH_TYPE_KM_KIRKWOOD)
+int ethernet_present(void)
+{
+ struct km_bec_fpga *base =
+ (struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
+
+ return in_8(&base->bprth) & PIGGY_PRESENT;
}
#endif
+
+int board_eth_init(bd_t *bis)
+{
+ if (ethernet_present())
+ return cpu_eth_init(bis);
+
+ return -1;
+}
+
+/*
+ * do_setboardid command
+ * read out the board id and the hw key from the intventory EEPROM and set
+ * this values as environment variables.
+ */
+static int do_setboardid(cmd_tbl_t *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ unsigned char buf[32];
+ char *p;
+
+ p = get_local_var("IVM_BoardId");
+ if (p == NULL) {
+ printf("can't get the IVM_Boardid\n");
+ return 1;
+ }
+ sprintf((char *)buf, "%s", p);
+ setenv("boardid", (char *)buf);
+
+ p = get_local_var("IVM_HWKey");
+ if (p == NULL) {
+ printf("can't get the IVM_HWKey\n");
+ return 1;
+ }
+ sprintf((char *)buf, "%s", p);
+ setenv("hwkey", (char *)buf);
+
+ return 0;
+}
+
+U_BOOT_CMD(km_setboardid, 1, 0, do_setboardid, "setboardid", "read out bid and "
+ "hwkey from IVM and set in environment");
projects / u-boot / blobdiff