at91sam9260ek: move board id setup to config header

[u-boot] / board / lwmon / pcmcia.c

diff --git a/board/lwmon/pcmcia.c b/board/lwmon/pcmcia.c
index 8825bd9714e5e0dada07310f44eb037d1c9f760e..acbb9d54d21d1626d1c32da98d68b29acfe971d9 100644 (file)
--- a/board/lwmon/pcmcia.c
+++ b/board/lwmon/pcmcia.c
@@ -29,8 +29,6 @@
 
 int pcmcia_hardware_enable(int slot)
 {
-       volatile immap_t        *immap;
-       volatile cpm8xx_t       *cp;
        volatile pcmconf8xx_t   *pcmp;
        volatile sysconf8xx_t   *sysp;
        uint reg, mask;
@@ -51,10 +49,8 @@ int pcmcia_hardware_enable(int slot)
 #endif
        udelay(10000);
 
-       immap = (immap_t *)CFG_IMMR;
-       sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-       pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-       cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+       sysp  = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
+       pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
 
        /*
         * Configure SIUMCR to enable PCMCIA port B
@@ -108,8 +104,8 @@ int pcmcia_hardware_enable(int slot)
 
        /*  switch VCC on */
        val |= MAX1604_OP_SUS | MAX1604_VCCBON;
-       i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
-       i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+       i2c_init  (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+       i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
 
        udelay(500000);
 
@@ -137,13 +133,13 @@ int pcmcia_hardware_disable(int slot)
 
        debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
 
-       immap = (immap_t *)CFG_IMMR;
-       pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+       immap = (immap_t *)CONFIG_SYS_IMMR;
+       pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
 
        /* remove all power, put output in high impedance state */
        val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
-       i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
-       i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+       i2c_init  (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+       i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
 
        /* Configure PCMCIA General Control Register */
        debug ("Disable PCMCIA buffers and assert RESET\n");
@@ -171,7 +167,6 @@ int pcmcia_hardware_disable(int slot)
 
 int pcmcia_voltage_set(int slot, int vcc, int vpp)
 {
-       volatile immap_t        *immap;
        volatile pcmconf8xx_t   *pcmp;
        u_long reg;
        uchar val;
@@ -181,8 +176,7 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
                " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
                'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
 
-       immap = (immap_t *)CFG_IMMR;
-       pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+       pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
        /*
         * Disable PCMCIA buffers (isolate the interface)
         * and assert RESET signal
@@ -199,8 +193,8 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
         */
        debug ("PCMCIA power OFF\n");
        val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
-       i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
-       i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+       i2c_init  (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+       i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
 
        val = 0;
        switch(vcc) {
@@ -216,7 +210,7 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
                pcmp->pcmc_pipr,
                (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
 
-       i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+       i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
        if (val) {
                debug ("PCMCIA powered at %sV\n",
                        (val & MAX1604_VCC_35) ? "3.3" : "5.0");