#include <common.h>
#include <mpc5xxx.h>
+#include <miiphy.h>
+#include <libfdt.h>
-#if defined(CONFIG_OF_FLAT_TREE)
-#include <ft_build.h>
-#endif
+#if defined(CONFIG_STATUS_LED)
+#include <status_led.h>
+#endif /* CONFIG_STATUS_LED */
/* Kollmorgen DPR initialization data */
struct init_elem {
}
+/*
+ * Additional PHY intialization. After being reset in mpc5xxx_fec_init_phy(),
+ * PHY goes into FX mode. To take it out of the FX mode and switch into
+ * desired TX operation, one needs to clear the FX_SEL bit of Mode Control
+ * Register.
+ */
+void reset_phy(void)
+{
+ unsigned short mode_control;
+
+ miiphy_read("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15, &mode_control);
+ miiphy_write("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15,
+ mode_control & 0xfffe);
+ return;
+}
+
#ifndef CFG_RAMBOOT
/*
* Helper function to initialize SDRAM controller.
*/
-static void sdram_start (int hi_addr)
+static void sdram_start(int hi_addr)
{
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
/*
* Initalize SDRAM - configure SDRAM controller, detect memory size.
*/
-long int initdram (int board_type)
+phys_size_t initdram(int board_type)
{
ulong dramsize = 0;
#ifndef CFG_RAMBOOT
ulong test1, test2;
+ /* According to AN3221 (MPC5200B SDRAM Initialization and
+ * Configuration), the SDelay register must be written a value of
+ * 0x00000004 as the first step of the SDRAM contorller configuration.
+ */
+ *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
+
/* configure SDRAM start/end for detection */
*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
}
-int checkboard (void)
+int checkboard(void)
{
- puts("Board: Promess Motion-PRO board\n");
+ uchar rev = *(vu_char *)CPLD_REV_REGISTER;
+ printf("Board: Promess Motion-PRO board (CPLD rev. 0x%02x)\n", rev);
return 0;
}
-#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
}
-#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
+
+
+#if defined(CONFIG_STATUS_LED)
+void __led_init(led_id_t regaddr, int state)
+{
+ *((vu_long *) regaddr) |= ENABLE_GPIO_OUT;
+
+ if (state == STATUS_LED_ON)
+ *((vu_long *) regaddr) |= LED_ON;
+ else
+ *((vu_long *) regaddr) &= ~LED_ON;
+}
+
+void __led_set(led_id_t regaddr, int state)
+{
+ if (state == STATUS_LED_ON)
+ *((vu_long *) regaddr) |= LED_ON;
+ else
+ *((vu_long *) regaddr) &= ~LED_ON;
+}
+
+void __led_toggle(led_id_t regaddr)
+{
+ *((vu_long *) regaddr) ^= LED_ON;
+}
+#endif /* CONFIG_STATUS_LED */