#include <linux/compiler.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
-#include <asm/arch/emc.h>
+#ifdef CONFIG_LCD
+#include <asm/arch/display.h>
+#endif
+#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/pmu.h>
+#ifdef CONFIG_PWM_TEGRA
+#include <asm/arch/pwm.h>
+#endif
#include <asm/arch/tegra.h>
-#include <asm/arch/usb.h>
#include <asm/arch-tegra/board.h>
#include <asm/arch-tegra/clk_rst.h>
#include <asm/arch-tegra/pmc.h>
#include <asm/arch-tegra/sys_proto.h>
#include <asm/arch-tegra/uart.h>
#include <asm/arch-tegra/warmboot.h>
-#include <spi.h>
+#ifdef CONFIG_TEGRA_CLOCK_SCALING
+#include <asm/arch/emc.h>
+#endif
+#ifdef CONFIG_USB_EHCI_TEGRA
+#include <asm/arch-tegra/usb.h>
+#endif
+#ifdef CONFIG_TEGRA_MMC
+#include <asm/arch-tegra/tegra_mmc.h>
+#include <asm/arch-tegra/mmc.h>
+#endif
#include <i2c.h>
-#include "board.h"
+#include <spi.h>
#include "emc.h"
DECLARE_GLOBAL_DATA_PTR;
void gpio_early_init_uart(void)
__attribute__((weak, alias("__gpio_early_init_uart")));
+void __pin_mux_nand(void)
+{
+ funcmux_select(PERIPH_ID_NDFLASH, FUNCMUX_DEFAULT);
+}
+
+void pin_mux_nand(void) __attribute__((weak, alias("__pin_mux_nand")));
+
+void __pin_mux_display(void)
+{
+}
+
+void pin_mux_display(void) __attribute__((weak, alias("__pin_mux_display")));
+
/*
* Routine: power_det_init
* Description: turn off power detects
#ifdef CONFIG_SPI_UART_SWITCH
gpio_config_uart();
#endif
-#ifdef CONFIG_TEGRA_SPI
+#if defined(CONFIG_TEGRA_SPI) || defined(CONFIG_TEGRA_SLINK)
pin_mux_spi();
spi_init();
#endif
+
+#ifdef CONFIG_PWM_TEGRA
+ if (pwm_init(gd->fdt_blob))
+ debug("%s: Failed to init pwm\n", __func__);
+#endif
+#ifdef CONFIG_LCD
+ pin_mux_display();
+ tegra_lcd_check_next_stage(gd->fdt_blob, 0);
+#endif
/* boot param addr */
gd->bd->bi_boot_params = (NV_PA_SDRAM_BASE + 0x100);
pin_mux_usb();
board_usb_init(gd->fdt_blob);
#endif
+#ifdef CONFIG_LCD
+ tegra_lcd_check_next_stage(gd->fdt_blob, 0);
+#endif
+
+#ifdef CONFIG_TEGRA_NAND
+ pin_mux_nand();
+#endif
#ifdef CONFIG_TEGRA_LP0
/* save Sdram params to PMC 2, 4, and 24 for WB0 */
int board_early_init_f(void)
{
+#if !defined(CONFIG_TEGRA20)
+ pinmux_init();
+#endif
board_init_uart_f();
/* Initialize periph GPIOs */
gpio_early_init();
gpio_early_init_uart();
+#ifdef CONFIG_LCD
+ tegra_lcd_early_init(gd->fdt_blob);
+#endif
return 0;
}
#endif /* EARLY_INIT */
+
+int board_late_init(void)
+{
+#ifdef CONFIG_LCD
+ /* Make sure we finish initing the LCD */
+ tegra_lcd_check_next_stage(gd->fdt_blob, 1);
+#endif
+ return 0;
+}
+
+#if defined(CONFIG_TEGRA_MMC)
+void __pin_mux_mmc(void)
+{
+}
+
+void pin_mux_mmc(void) __attribute__((weak, alias("__pin_mux_mmc")));
+
+/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+ debug("%s called\n", __func__);
+
+ /* Enable muxes, etc. for SDMMC controllers */
+ pin_mux_mmc();
+
+ debug("%s: init MMC\n", __func__);
+ tegra_mmc_init();
+
+ return 0;
+}
+
+void pad_init_mmc(struct mmc_host *host)
+{
+#if defined(CONFIG_TEGRA30)
+ enum periph_id id = host->mmc_id;
+ u32 val;
+
+ debug("%s: sdmmc address = %08x, id = %d\n", __func__,
+ (unsigned int)host->reg, id);
+
+ /* Set the pad drive strength for SDMMC1 or 3 only */
+ if (id != PERIPH_ID_SDMMC1 && id != PERIPH_ID_SDMMC3) {
+ debug("%s: settings are only valid for SDMMC1/SDMMC3!\n",
+ __func__);
+ return;
+ }
+
+ val = readl(&host->reg->sdmemcmppadctl);
+ val &= 0xFFFFFFF0;
+ val |= MEMCOMP_PADCTRL_VREF;
+ writel(val, &host->reg->sdmemcmppadctl);
+
+ val = readl(&host->reg->autocalcfg);
+ val &= 0xFFFF0000;
+ val |= AUTO_CAL_PU_OFFSET | AUTO_CAL_PD_OFFSET | AUTO_CAL_ENABLED;
+ writel(val, &host->reg->autocalcfg);
+#endif /* T30 */
+}
+#endif /* MMC */