extern flash_info_t flash_info[];
ulong flash_get_size (phys_addr_t base, int banknum);
-/* Clocks in use */
-#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \
- CLOCK_SCCR1_LPC_EN | \
- CLOCK_SCCR1_NFC_EN | \
- CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \
- CLOCK_SCCR1_PSCFIFO_EN | \
- CLOCK_SCCR1_DDR_EN | \
- CLOCK_SCCR1_FEC_EN | \
- CLOCK_SCCR1_TPR_EN)
-
-#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \
- CLOCK_SCCR2_SPDIF_EN | \
- CLOCK_SCCR2_DIU_EN | \
- CLOCK_SCCR2_I2C_EN)
-
-int board_early_init_f(void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
- /*
- * Initialize Local Window for FLASH-Bank1 access (CS1)
- */
- out_be32(&im->sysconf.lpcs1aw,
- CSAW_START(CONFIG_SYS_FLASH1_BASE) |
- CSAW_STOP(CONFIG_SYS_FLASH1_BASE, CONFIG_SYS_FLASH_SIZE)
- );
- out_be32(&im->lpc.cs_cfg[1], CONFIG_SYS_CS1_CFG);
-
- /*
- * Local Window for MRAM access (CS2)
- */
- out_be32(&im->sysconf.lpcs2aw,
- CSAW_START(CONFIG_SYS_MRAM_BASE) |
- CSAW_STOP(CONFIG_SYS_MRAM_BASE, CONFIG_SYS_MRAM_SIZE)
- );
- out_be32(&im->lpc.cs_cfg[2], CONFIG_SYS_CS2_CFG);
-
- sync_law(&im->sysconf.lpcs2aw);
-
- /*
- * Configure Flash Speed
- */
- out_be32(&im->lpc.cs_cfg[0], CONFIG_SYS_CS0_CFG);
- out_be32(&im->lpc.altr, CONFIG_SYS_CS_ALETIMING);
-
- /*
- * Enable clocks
- */
- out_be32(&im->clk.sccr[0], SCCR1_CLOCKS_EN);
- out_be32(&im->clk.sccr[1], SCCR2_CLOCKS_EN);
-#if defined(CONFIG_IIM) || defined(CONFIG_CMD_FUSE)
- setbits_be32(&im->clk.sccr[1], CLOCK_SCCR2_IIM_EN);
-#endif
-
- return 0;
-}
-
sdram_conf_t mddrc_config[] = {
{
(512 << 20), /* 512 MB RAM configuration */
return msize;
}
-#if defined(CONFIG_SERIAL_MULTI)
static int set_lcd_brightness(char *);
-#endif
int misc_init_r(void)
{
#endif
#ifdef CONFIG_FSL_DIU_FB
-# if !(defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE))
- mpc5121_diu_init();
-#endif
-#if defined(CONFIG_SERIAL_MULTI)
set_lcd_brightness(0);
-#endif
/* Switch LCD-Backlight and LVDS-Interface on */
setbits_be32(&im->gpio.gpdir, 0x01040000);
clrsetbits_be32(&im->gpio.gpdat, 0x01000000, 0x00040000);
};
#endif
+#if defined(CONFIG_VIDEO)
+/*
+ * EDID block has been generated using Phoenix EDID Designer 1.3.
+ * This tool creates a text file containing:
+ *
+ * EDID BYTES:
+ * 0x 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
+ * ------------------------------------------------
+ * 00 | 00 FF FF FF FF FF FF 00 42 C9 34 12 01 00 00 00
+ * 10 | 0A 0C 01 03 80 98 5B 78 CA 7E 50 A0 58 4E 96 25
+ * 20 | 1E 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
+ * 30 | 01 01 01 01 01 01 80 0C 20 00 31 E0 2D 10 2A 80
+ * 40 | 12 08 30 E4 10 00 00 18 00 00 00 FD 00 38 3C 1F
+ * 50 | 3C 04 0A 20 20 20 20 20 20 20 00 00 00 FF 00 50
+ * 60 | 4D 30 37 30 57 4C 33 0A 0A 0A 0A 0A 00 00 00 FF
+ * 70 | 00 41 30 30 30 30 30 30 30 30 30 30 30 31 00 D4
+ *
+ * Then this data has been manually converted to the char
+ * array below.
+ */
+static unsigned char edid_buf[128] = {
+ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00,
+ 0x42, 0xC9, 0x34, 0x12, 0x01, 0x00, 0x00, 0x00,
+ 0x0A, 0x0C, 0x01, 0x03, 0x80, 0x98, 0x5B, 0x78,
+ 0xCA, 0x7E, 0x50, 0xA0, 0x58, 0x4E, 0x96, 0x25,
+ 0x1E, 0x50, 0x54, 0x00, 0x00, 0x00, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x80, 0x0C,
+ 0x20, 0x00, 0x31, 0xE0, 0x2D, 0x10, 0x2A, 0x80,
+ 0x12, 0x08, 0x30, 0xE4, 0x10, 0x00, 0x00, 0x18,
+ 0x00, 0x00, 0x00, 0xFD, 0x00, 0x38, 0x3C, 0x1F,
+ 0x3C, 0x04, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20,
+ 0x20, 0x20, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x50,
+ 0x4D, 0x30, 0x37, 0x30, 0x57, 0x4C, 0x33, 0x0A,
+ 0x0A, 0x0A, 0x0A, 0x0A, 0x00, 0x00, 0x00, 0xFF,
+ 0x00, 0x41, 0x30, 0x30, 0x30, 0x30, 0x30, 0x30,
+ 0x30, 0x30, 0x30, 0x30, 0x30, 0x31, 0x00, 0xD4,
+};
+#endif
+
void ft_board_setup(void *blob, bd_t *bd)
{
u32 val[8];
int rc, i = 0;
ft_cpu_setup(blob, bd);
- fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize);
#ifdef CONFIG_FDT_FIXUP_PARTITIONS
fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
#endif
+#if defined(CONFIG_VIDEO)
+ fdt_add_edid(blob, "fsl,mpc5121-diu", edid_buf);
+#endif
/* Fixup NOR FLASH mapping */
val[i++] = 0; /* chip select number */
}
#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-#if defined(CONFIG_SERIAL_MULTI)
/*
* If argument is NULL, set the LCD brightness to the
* value from "brightness" environment variable. Set
"set LCD brightness",
"<brightness> - set LCD backlight level to <brightness>.\n"
);
-#endif /* CONFIG_SERIAL_MULTI */