/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* Setup pin multiplexing (GPIO/IRQ...)
*-------------------------------------------------------------------*/
- mtdcr(cpc0_gpio, 0x03F01F80);
+ mtdcr(CPC0_GPIO, 0x03F01F80);
out32(GPIO0_ODR, 0x00000000); /* no open drain pins */
out32(GPIO0_TCR, CONFIG_SYS_GPIO_RDY | CONFIG_SYS_EREADY_IO | CONFIG_SYS_LED_RED | CONFIG_SYS_LED_GREEN);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
- mtdcr(uic0sr, 0xffffffff); /* clear all */
- mtdcr(uic0er, 0x00000000); /* disable all */
- mtdcr(uic0cr, 0x00000001); /* UIC1 crit is critical */
- mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */
- mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */
- mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic0sr, 0xffffffff); /* clear all */
-
- mtdcr(uic1sr, 0xffffffff); /* clear all */
- mtdcr(uic1er, 0x00000000); /* disable all */
- mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */
- mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */
- mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic1sr, 0xffffffff); /* clear all */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000001); /* UIC1 crit is critical */
+ mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
return 0;
}
int checkboard(void)
{
- char *s = getenv("serial#");
+ char buf[64];
+ int i = getenv_f("serial#", buf, sizeof(buf));
printf("Board: P3P440");
- if (s != NULL) {
+ if (i > 0) {
puts(", serial# ");
- puts(s);
+ puts(buf);
}
if (is_monarch()) {
* Check if only one FLASH bank is available
*/
if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
- mtebc(pb1cr, 0); /* disable cs */
- mtebc(pb1ap, 0);
- mtebc(pb2cr, 0); /* disable cs */
- mtebc(pb2ap, 0);
- mtebc(pb3cr, 0); /* disable cs */
- mtebc(pb3ap, 0);
+ mtebc(PB1CR, 0); /* disable cs */
+ mtebc(PB1AP, 0);
+ mtebc(PB2CR, 0); /* disable cs */
+ mtebc(PB2AP, 0);
+ mtebc(PB3CR, 0); /* disable cs */
+ mtebc(PB3AP, 0);
}
return 0;
}
/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The P3P440 board is always configured as the host & requires the
- * PCI arbiter to be disabled because it's an PMC module.
- *--------------------------------------------------------------------------*/
- strap = mfdcr(cpc0_strp1);
- if (strap & 0x00100000) {
- printf("PCI: CPC0_STRP1[PAE] set.\n");
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r(PCIX0_PIM0SA, 0); /* disable */
- out32r(PCIX0_PIM1SA, 0); /* disable */
- out32r(PCIX0_PIM2SA, 0); /* disable */
- out32r(PCIX0_EROMBA, 0); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r(PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIX0_PIM0LAH, 0);
- out32r(PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIX0_BAR0, 0);
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r(PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * is_pci_host
+ * Override weak is_pci_host()
*
* This routine is called to determine if a pci scan should be
* performed. With various hardware environments (especially cPCI and