ARM: dts: am335x-evm: disable mmc3

[u-boot] / board / ronetix / pm9261 / pm9261.c

diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c
index 1f7679a240e453cc45d9a7ea1b2f33fccdb2d111..79073d8aaaf15191ac430d6dbcb9397fed589712 100644 (file)
--- a/board/ronetix/pm9261/pm9261.c
+++ b/board/ronetix/pm9261/pm9261.c
@@ -14,7 +14,6 @@
 #include <asm/gpio.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
-#include <asm/arch/at91_pmc.h>
 #include <asm/arch/at91_rstc.h>
 #include <asm/arch/at91_matrix.h>
 #include <asm/arch/clk.h>
@@ -41,7 +40,6 @@ static void pm9261_nand_hw_init(void)
        unsigned long csa;
        struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
        struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
-       struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
 
        /* Enable CS3 */
        csa = readl(&matrix->csa) | AT91_MATRIX_CSA_EBI_CS3A;
@@ -69,9 +67,8 @@ static void pm9261_nand_hw_init(void)
                AT91_SMC_MODE_TDF_CYCLE(2),
                &smc->cs[3].mode);
 
-       writel(1 << ATMEL_ID_PIOA |
-               1 << ATMEL_ID_PIOC,
-               &pmc->pcer);
+       at91_periph_clk_enable(ATMEL_ID_PIOA);
+       at91_periph_clk_enable(ATMEL_ID_PIOC);
 
        /* Configure RDY/BSY */
        gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
@@ -89,7 +86,6 @@ static void pm9261_nand_hw_init(void)
 static void pm9261_dm9000_hw_init(void)
 {
        struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
-       struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
 
        /* Configure SMC CS2 for DM9000 */
        writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
@@ -110,7 +106,7 @@ static void pm9261_dm9000_hw_init(void)
                &smc->cs[2].mode);
 
        /* Configure Interrupt pin as input, no pull-up */
-       writel(1 << ATMEL_ID_PIOA, &pmc->pcer);
+       at91_periph_clk_enable(ATMEL_ID_PIOA);
        at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
 }
 #endif
@@ -145,8 +141,6 @@ void lcd_disable(void)
 
 static void pm9261_lcd_hw_init(void)
 {
-       struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
        at91_set_a_periph(AT91_PIO_PORTB, 1, 0);        /* LCDHSYNC */
        at91_set_a_periph(AT91_PIO_PORTB, 2, 0);        /* LCDDOTCK */
        at91_set_a_periph(AT91_PIO_PORTB, 3, 0);        /* LCDDEN */
@@ -170,7 +164,7 @@ static void pm9261_lcd_hw_init(void)
        at91_set_b_periph(AT91_PIO_PORTB, 27, 0);       /* LCDD22 */
        at91_set_b_periph(AT91_PIO_PORTB, 28, 0);       /* LCDD23 */
 
-       writel(1 << 17, &pmc->scer); /* LCD controller Clock, AT91SAM9261 only */
+       at91_system_clk_enable(AT91_PMC_HCK1);
 
        gd->fb_base = ATMEL_BASE_SRAM;
 }
@@ -200,7 +194,7 @@ void lcd_show_board_info(void)
 
        nand_size = 0;
        for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
-               nand_size += nand_info[i].size;
+               nand_size += nand_info[i]->size;
 
        flash_size = 0;
        for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
@@ -224,12 +218,8 @@ void lcd_show_board_info(void)
 
 int board_early_init_f(void)
 {
-       struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
-       /* Enable clocks for some PIOs */
-       writel(1 << ATMEL_ID_PIOA |
-               1 << ATMEL_ID_PIOC,
-               &pmc->pcer);
+       at91_periph_clk_enable(ATMEL_ID_PIOA);
+       at91_periph_clk_enable(ATMEL_ID_PIOC);
 
        at91_seriald_hw_init();
 
@@ -274,10 +264,12 @@ int dram_init(void)
        return 0;
 }
 
-void dram_init_banksize(void)
+int dram_init_banksize(void)
 {
        gd->bd->bi_dram[0].start = PHYS_SDRAM;
        gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+
+       return 0;
 }
 
 #ifdef CONFIG_RESET_PHY_R
@@ -288,7 +280,7 @@ void reset_phy(void)
         * Initialize ethernet HW addr prior to starting Linux,
         * needed for nfsroot
         */
-       eth_init(gd->bd);
+       eth_init();
 #endif
 }
 #endif