#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/adc.h>
-#include <asm/arch/gpio.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/watchdog.h>
#include <ld9040.h>
#include <power/pmic.h>
#include <usb.h>
-#include <usb/s3c_udc.h>
+#include <usb/dwc2_udc.h>
#include <asm/arch/cpu.h>
#include <power/max8998_pmic.h>
#include <libtizen.h>
return 0;
}
-struct s3c_plat_otg_data s5pc210_otg_data = {
+struct dwc2_plat_otg_data s5pc210_otg_data = {
.phy_control = s5pc210_phy_control,
.regs_phy = EXYNOS4_USBPHY_BASE,
.regs_otg = EXYNOS4_USBOTG_BASE,
int board_usb_init(int index, enum usb_init_type init)
{
debug("USB_udc_probe\n");
- return s3c_udc_probe(&s5pc210_otg_data);
+ return dwc2_udc_probe(&s5pc210_otg_data);
}
int exynos_early_init_f(void)
return 0;
}
-#ifdef CONFIG_SOFT_SPI
-static void soft_spi_init(void)
-{
- gpio_direction_output(CONFIG_SOFT_SPI_GPIO_SCLK,
- CONFIG_SOFT_SPI_MODE & SPI_CPOL);
- gpio_direction_output(CONFIG_SOFT_SPI_GPIO_MOSI, 1);
- gpio_direction_input(CONFIG_SOFT_SPI_GPIO_MISO);
- gpio_direction_output(CONFIG_SOFT_SPI_GPIO_CS,
- !(CONFIG_SOFT_SPI_MODE & SPI_CS_HIGH));
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- gpio_set_value(CONFIG_SOFT_SPI_GPIO_CS,
- !(CONFIG_SOFT_SPI_MODE & SPI_CS_HIGH));
- SPI_SCL(1);
- gpio_set_value(CONFIG_SOFT_SPI_GPIO_CS,
- CONFIG_SOFT_SPI_MODE & SPI_CS_HIGH);
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- gpio_set_value(CONFIG_SOFT_SPI_GPIO_CS,
- !(CONFIG_SOFT_SPI_MODE & SPI_CS_HIGH));
-}
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs == 0;
-}
-
-void universal_spi_scl(int bit)
-{
- gpio_set_value(CONFIG_SOFT_SPI_GPIO_SCLK, bit);
-}
-
-void universal_spi_sda(int bit)
-{
- gpio_set_value(CONFIG_SOFT_SPI_GPIO_MOSI, bit);
-}
-
-int universal_spi_read(void)
-{
- return gpio_get_value(CONFIG_SOFT_SPI_GPIO_MISO);
-}
-#endif
-
static void init_pmic_lcd(void)
{
unsigned char val;
}
/* gpio pad configuration for LCD reset. */
+ gpio_request(EXYNOS4_GPIO_Y45, "lcd_reset");
gpio_cfg_pin(EXYNOS4_GPIO_Y45, S5P_GPIO_OUTPUT);
-
- spi_init();
}
int mipi_power(void)
int exynos_init(void)
{
+ char buf[16];
+
gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210;
switch (get_hwrev()) {
* you should set it HIGH since it removes the inverter
*/
/* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */
+ gpio_request(EXYNOS4_GPIO_E36, "ldo_en");
gpio_direction_output(EXYNOS4_GPIO_E36, 0);
break;
default:
* But set it as HIGH to ensure
*/
/* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */
+ gpio_request(EXYNOS4_GPIO_E13, "massmemory_en");
gpio_direction_output(EXYNOS4_GPIO_E13, 1);
break;
}
-#ifdef CONFIG_SOFT_SPI
- soft_spi_init();
-#endif
+ /* Request soft I2C gpios */
+ strcpy(buf, "soft_i2c_scl");
+ gpio_request(CONFIG_SOFT_I2C_GPIO_SCL, buf);
+
+ strcpy(buf, "soft_i2c_sda");
+ gpio_request(CONFIG_SOFT_I2C_GPIO_SDA, buf);
+
check_hw_revision();
printf("HW Revision:\t0x%x\n", board_rev);