#include <asm/gpio.h>
#include <asm/arch/adc.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/watchdog.h>
-#include <libtizen.h>
#include <ld9040.h>
#include <power/pmic.h>
+#include <usb.h>
#include <usb/s3c_udc.h>
#include <asm/arch/cpu.h>
#include <power/max8998_pmic.h>
+#include <libtizen.h>
+#include <samsung/misc.h>
+#include <usb_mass_storage.h>
DECLARE_GLOBAL_DATA_PTR;
static void init_pmic_lcd(void);
-int power_init_board(void)
+int exynos_power_init(void)
{
int ret;
return 0;
}
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) +
- get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-}
-
static unsigned short get_adc_value(int channel)
{
struct s5p_adc *adc = (struct s5p_adc *)samsung_get_base_adc();
board_rev |= hwrev;
}
-#ifdef CONFIG_DISPLAY_BOARDINFO
-int checkboard(void)
-{
- puts("Board:\tUniversal C210\n");
- return 0;
-}
-#endif
-
-#ifdef CONFIG_GENERIC_MMC
-int board_mmc_init(bd_t *bis)
-{
- int err;
-
- switch (get_hwrev()) {
- case 0:
- /*
- * Set the low to enable LDO_EN
- * But when you use the test board for eMMC booting
- * you should set it HIGH since it removes the inverter
- */
- /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */
- s5p_gpio_direction_output(&gpio1->e3, 6, 0);
- break;
- default:
- /*
- * Default reset state is High and there's no inverter
- * But set it as HIGH to ensure
- */
- /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */
- s5p_gpio_direction_output(&gpio1->e1, 3, 1);
- break;
- }
-
- /*
- * MMC device init
- * mmc0 : eMMC (8-bit buswidth)
- * mmc2 : SD card (4-bit buswidth)
- */
- err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
- if (err)
- debug("SDMMC0 not configured\n");
- else
- err = s5p_mmc_init(0, 8);
-
- /* T-flash detect */
- s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf);
- s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP);
-
- /*
- * Check the T-flash detect pin
- * GPX3[4] T-flash detect pin
- */
- if (!s5p_gpio_get_value(&gpio2->x3, 4)) {
- err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
- if (err)
- debug("SDMMC2 not configured\n");
- else
- err = s5p_mmc_init(2, 4);
- }
-
- return err;
-
-}
-#endif
-
#ifdef CONFIG_USB_GADGET
static int s5pc210_phy_control(int on)
{
};
#endif
-int board_early_init_f(void)
+int board_usb_init(int index, enum usb_init_type init)
+{
+ debug("USB_udc_probe\n");
+ return s3c_udc_probe(&s5pc210_otg_data);
+}
+
+int exynos_early_init_f(void)
{
wdt_stop();
spi_init();
}
+int mipi_power(void)
+{
+ return 0;
+}
+
void exynos_reset_lcd(void)
{
s5p_gpio_set_value(&gpio2->y4, 5, 1);
pmic_set_output(p, MAX8998_REG_ONOFF2, MAX8998_LDO7, LDO_ON);
}
-vidinfo_t panel_info = {
- .vl_freq = 60,
- .vl_col = 480,
- .vl_row = 800,
- .vl_width = 480,
- .vl_height = 800,
- .vl_clkp = CONFIG_SYS_HIGH,
- .vl_hsp = CONFIG_SYS_HIGH,
- .vl_vsp = CONFIG_SYS_HIGH,
- .vl_dp = CONFIG_SYS_HIGH,
-
- .vl_bpix = 5, /* Bits per pixel */
-
- /* LD9040 LCD Panel */
- .vl_hspw = 2,
- .vl_hbpd = 16,
- .vl_hfpd = 16,
-
- .vl_vspw = 2,
- .vl_vbpd = 8,
- .vl_vfpd = 8,
- .vl_cmd_allow_len = 0xf,
-
- .win_id = 0,
- .dual_lcd_enabled = 0,
-
- .init_delay = 0,
- .power_on_delay = 10000,
- .reset_delay = 10000,
- .interface_mode = FIMD_RGB_INTERFACE,
- .mipi_enabled = 0,
-};
-
void exynos_cfg_ldo(void)
{
ld9040_cfg_ldo();
ld9040_enable_ldo(onoff);
}
-void init_panel_info(vidinfo_t *vid)
-{
- vid->logo_on = 1;
- vid->resolution = HD_RESOLUTION;
- vid->rgb_mode = MODE_RGB_P;
-
-#ifdef CONFIG_TIZEN
- get_tizen_logo_info(vid);
-#endif
-
- /* for LD9040. */
- vid->pclk_name = 1; /* MPLL */
- vid->sclk_div = 1;
-
- setenv("lcdinfo", "lcd=ld9040");
-}
-
-int board_init(void)
+int exynos_init(void)
{
gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE;
gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE;
gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210;
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ switch (get_hwrev()) {
+ case 0:
+ /*
+ * Set the low to enable LDO_EN
+ * But when you use the test board for eMMC booting
+ * you should set it HIGH since it removes the inverter
+ */
+ /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */
+ s5p_gpio_direction_output(&gpio1->e3, 6, 0);
+ break;
+ default:
+ /*
+ * Default reset state is High and there's no inverter
+ * But set it as HIGH to ensure
+ */
+ /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */
+ s5p_gpio_direction_output(&gpio1->e1, 3, 1);
+ break;
+ }
#ifdef CONFIG_SOFT_SPI
soft_spi_init();
return 0;
}
+
+void exynos_lcd_misc_init(vidinfo_t *vid)
+{
+#ifdef CONFIG_TIZEN
+ get_tizen_logo_info(vid);
+#endif
+
+ /* for LD9040. */
+ vid->pclk_name = 1; /* MPLL */
+ vid->sclk_div = 1;
+
+ setenv("lcdinfo", "lcd=ld9040");
+}