#include <libfdt.h>
#include <fdt_support.h>
-long int fixed_sdram (void);
-
/*
* I/O Port configuration table
*
#endif
#if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC)
/* reset PHY */
- miiphy_reset("FCC1 ETHERNET", 0x0);
+ miiphy_reset("FCC1", 0x0);
/* change PHY address to 0x02 */
- bb_miiphy_write(NULL, 0, PHY_MIPSCR, 0xf028);
+ bb_miiphy_write(NULL, 0, MII_MIPSCR, 0xf028);
- bb_miiphy_write(NULL, 0x02, PHY_BMCR,
- PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
+ bb_miiphy_write(NULL, 0x02, MII_BMCR,
+ BMCR_ANENABLE | BMCR_ANRESTART);
#endif /* CONFIG_MII */
}
#else
printf ("Board: Wind River SBC8540 Board\n");
#endif
- printf ("\tCPU: %s MHz\n", strmhz(buf, sysinfo.freqProcessor));
+ printf ("\tCPU: %s MHz\n", strmhz(buf, sysinfo.freqProcessor[0]));
printf ("\tCCB: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus));
printf ("\tDDR: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus/2));
if((CONFIG_SYS_LBC_LCRR & 0x0f) == 2 || (CONFIG_SYS_LBC_LCRR & 0x0f) == 4 \
}
-phys_size_t initdram (int board_type)
-{
- long dram_size = 0;
-
-#if 0
-#if !defined(CONFIG_RAM_AS_FLASH)
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
- sys_info_t sysinfo;
- uint temp_lbcdll = 0;
-#endif
-#endif /* 0 */
-#if !defined(CONFIG_RAM_AS_FLASH) || defined(CONFIG_DDR_DLL)
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-#endif
-#if defined(CONFIG_DDR_DLL)
- uint temp_ddrdll = 0;
-
- /* Work around to stabilize DDR DLL */
- temp_ddrdll = gur->ddrdllcr;
- gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
- asm("sync;isync;msync");
-#endif
-
-#if defined(CONFIG_SPD_EEPROM)
- dram_size = fsl_ddr_sdram();
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
-#else
- dram_size = fixed_sdram ();
-#endif
-
-#if 0
-#if !defined(CONFIG_RAM_AS_FLASH) /* LocalBus SDRAM is not emulating flash */
- get_sys_info(&sysinfo);
- /* if localbus freq is less than 66Mhz,we use bypass mode,otherwise use DLL */
- if(sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & 0x0f) < 66000000) {
- lbc->lcrr = (CONFIG_SYS_LBC_LCRR & 0x0fffffff)| 0x80000000;
- } else {
-#if defined(CONFIG_MPC85xx_REV1) /* need change CLKDIV before enable DLL */
- lbc->lcrr = 0x10000004; /* default CLKDIV is 8, change it to 4 temporarily */
-#endif
- lbc->lcrr = CONFIG_SYS_LBC_LCRR & 0x7fffffff;
- udelay(200);
- temp_lbcdll = gur->lbcdllcr;
- gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16 ) | 0x80000000;
- asm("sync;isync;msync");
- }
- lbc->or2 = CONFIG_SYS_OR2_PRELIM; /* 64MB SDRAM */
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
- lbc->lbcr = CONFIG_SYS_LBC_LBCR;
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_1;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_2;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_3;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_4;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_5;
- asm("sync");
- lbc->lsrt = CONFIG_SYS_LBC_LSRT;
- asm("sync");
- lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
- asm("sync");
-#endif
-#endif
-
-#if defined(CONFIG_DDR_ECC)
- {
- /* Initialize all of memory for ECC, then
- * enable errors */
- uint *p = 0;
- uint i = 0;
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
- dma_init();
- for (*p = 0; p < (uint *)(8 * 1024); p++) {
- if (((unsigned int)p & 0x1f) == 0) { dcbz(p); }
- *p = (unsigned int)0xdeadbeef;
- if (((unsigned int)p & 0x1c) == 0x1c) { dcbf(p); }
- }
-
- /* 8K */
- dma_xfer((uint *)0x2000,0x2000,(uint *)0);
- /* 16K */
- dma_xfer((uint *)0x4000,0x4000,(uint *)0);
- /* 32K */
- dma_xfer((uint *)0x8000,0x8000,(uint *)0);
- /* 64K */
- dma_xfer((uint *)0x10000,0x10000,(uint *)0);
- /* 128k */
- dma_xfer((uint *)0x20000,0x20000,(uint *)0);
- /* 256k */
- dma_xfer((uint *)0x40000,0x40000,(uint *)0);
- /* 512k */
- dma_xfer((uint *)0x80000,0x80000,(uint *)0);
- /* 1M */
- dma_xfer((uint *)0x100000,0x100000,(uint *)0);
- /* 2M */
- dma_xfer((uint *)0x200000,0x200000,(uint *)0);
- /* 4M */
- dma_xfer((uint *)0x400000,0x400000,(uint *)0);
-
- for (i = 1; i < dram_size / 0x800000; i++) {
- dma_xfer((uint *)(0x800000*i),0x800000,(uint *)0);
- }
-
- /* Enable errors for ECC */
- ddr->err_disable = 0x00000000;
- asm("sync;isync;msync");
- }
-#endif
-
- return dram_size;
-}
-
-
#if defined(CONFIG_SYS_DRAM_TEST)
int testdram (void)
{
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
************************************************************************/
-long int fixed_sdram (void)
+phys_size_t fixed_sdram(void)
{
#define CONFIG_SYS_DDR_CONTROL 0xc2000000