endif
+config SYS_CLK_FREQ
+ default 912000000 if MACH_SUN7I
+ default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
+
config SYS_CONFIG_NAME
default "sun4i" if MACH_SUN4I
default "sun5i" if MACH_SUN5I
bool "SPL/FEL mode support"
depends on SPL
default n
+ help
+ This enables support for Fast Early Loader (FEL) mode. This
+ allows U-Boot to be loaded to the board over USB by the on-chip
+ boot rom. U-Boot should be sent in two parts: SPL first, with
+ 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
+ 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
+ shrinks the amount of SRAM available to SPL, so only enable it if
+ you need FEL. Note that enabling this option only allows FEL to be
+ used; it is still possible to boot U-Boot from boot media. U-Boot
+ SPL detects when it is being loaded using FEL.
config UART0_PORT_F
bool "UART0 on MicroSD breakout board"
Set the Vbus enable pin for usb0 (otg). This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config USB0_VBUS_DET
+ string "Vbus detect pin for usb0 (otg)"
+ depends on USB_MUSB_SUNXI
+ default ""
+ ---help---
+ Set the Vbus detect pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config USB1_VBUS_PIN
string "Vbus enable pin for usb1 (ehci0)"
default "PH6" if MACH_SUN4I || MACH_SUN7I
Set the power enable pin for the LCD panel. This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config VIDEO_LCD_RESET
+ string "LCD panel reset pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the reset pin for the LCD panel. This takes a string in the format
+ understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config VIDEO_LCD_BL_EN
string "LCD panel backlight enable pin"
depends on VIDEO
---help---
Set this if the backlight pwm output is active low.
+config VIDEO_LCD_PANEL_I2C
+ bool "LCD panel needs to be configured via i2c"
+ depends on VIDEO
+ default n
+ ---help---
+ Say y here if the LCD panel needs to be configured via i2c. This
+ will add a bitbang i2c controller using gpios to talk to the LCD.
+
+config VIDEO_LCD_PANEL_I2C_SDA
+ string "LCD panel i2c interface SDA pin"
+ depends on VIDEO_LCD_PANEL_I2C
+ default "PG12"
+ ---help---
+ Set the SDA pin for the LCD i2c interface. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_PANEL_I2C_SCL
+ string "LCD panel i2c interface SCL pin"
+ depends on VIDEO_LCD_PANEL_I2C
+ default "PG10"
+ ---help---
+ Set the SCL pin for the LCD i2c interface. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
# Note only one of these may be selected at a time! But hidden choices are
# not supported by Kconfig
---help---
7.85" 1024x768 Hitachi tx18d42vm LCD panel support
+config VIDEO_LCD_TL059WV5C0
+ bool "tl059wv5c0 LCD panel"
+ select VIDEO_LCD_PANEL_I2C
+ select VIDEO_LCD_IF_PARALLEL
+ ---help---
+ 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and
+ Aigo M60/M608/M606 tablets.
+
endchoice