arm: socfpga: config: Enable CONFIG_SPI_FLASH_BAR

[u-boot] / board / sunxi / board.c

diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index ed60e74808ffd4c8b6187d5cb5f1c0d231a40e8c..afed6a31cab6732f334d8dba2272730ee8306ac4 100644 (file)
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -31,7 +31,6 @@
 #include <asm/arch/usb_phy.h>
 #include <asm/gpio.h>
 #include <asm/io.h>
-#include <linux/usb/musb.h>
 #include <net.h>
 
 #if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
@@ -294,21 +293,19 @@ int board_mmc_init(bd_t *bis)
                return -1;
 #endif
 
-#if CONFIG_MMC_SUNXI_SLOT == 0 && CONFIG_MMC_SUNXI_SLOT_EXTRA == 2
+#if !defined(CONFIG_SPL_BUILD) && CONFIG_MMC_SUNXI_SLOT_EXTRA == 2
        /*
-        * Both mmc0 and mmc2 are bootable, figure out where we're booting
-        * from. Try mmc0 first, just like the brom does.
+        * On systems with an emmc (mmc2), figure out if we are booting from
+        * the emmc and if we are make it "mmc dev 0" so that boot.scr, etc.
+        * are searched there first. Note we only do this for u-boot proper,
+        * not for the SPL, see spl_boot_device().
         */
-       if (mmc_getcd(mmc0) && mmc_init(mmc0) == 0 &&
-           mmc0->block_dev.block_read(0, 16, 1, buf) == 1) {
-               buf[12] = 0;
-               if (strcmp(&buf[4], "eGON.BT0") == 0)
-                       return 0;
+       if (!sunxi_mmc_has_egon_boot_signature(mmc0) &&
+           sunxi_mmc_has_egon_boot_signature(mmc1)) {
+               /* Booting from emmc / mmc2, swap */
+               mmc0->block_dev.dev = 1;
+               mmc1->block_dev.dev = 0;
        }
-
-       /* no bootable card in mmc0, so we must be booting from mmc2, swap */
-       mmc0->block_dev.dev = 1;
-       mmc1->block_dev.dev = 0;
 #endif
 
        return 0;
@@ -451,28 +448,6 @@ void sunxi_board_init(void)
 }
 #endif
 
-#if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET)
-extern const struct musb_platform_ops sunxi_musb_ops;
-
-static struct musb_hdrc_config musb_config = {
-       .multipoint     = 1,
-       .dyn_fifo       = 1,
-       .num_eps        = 6,
-       .ram_bits       = 11,
-};
-
-static struct musb_hdrc_platform_data musb_plat = {
-#if defined(CONFIG_MUSB_HOST)
-       .mode           = MUSB_HOST,
-#else
-       .mode           = MUSB_PERIPHERAL,
-#endif
-       .config         = &musb_config,
-       .power          = 250,
-       .platform_ops   = &sunxi_musb_ops,
-};
-#endif
-
 #ifdef CONFIG_USB_GADGET
 int g_dnl_board_usb_cable_connected(void)
 {
@@ -535,9 +510,8 @@ int misc_init_r(void)
        if (ret)
                return ret;
 #endif
-#if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET)
-       musb_register(&musb_plat, NULL, (void *)SUNXI_USB0_BASE);
-#endif
+       sunxi_musb_board_init();
+
        return 0;
 }
 #endif