#include "mux_data.h"
#define board_is_x15() board_ti_is("BBRDX15_")
+#define board_is_x15_revb1() (board_ti_is("BBRDX15_") && \
+ !strncmp("B.10", board_ti_get_rev(), 3))
+#define board_is_x15_revc() (board_ti_is("BBRDX15_") && \
+ !strncmp("C.00", board_ti_get_rev(), 3))
#define board_is_am572x_evm() board_ti_is("AM572PM_")
+#define board_is_am572x_evm_reva3() \
+ (board_ti_is("AM572PM_") && \
+ !strncmp("A.30", board_ti_get_rev(), 3))
#define board_is_am572x_idk() board_ti_is("AM572IDK")
+#define board_is_am571x_idk() board_ti_is("AM571IDK")
#ifdef CONFIG_DRIVER_TI_CPSW
#include <cpsw.h>
DECLARE_GLOBAL_DATA_PTR;
+#define GPIO_ETH_LCD GPIO_TO_PIN(2, 22)
/* GPIO 7_11 */
#define GPIO_DDR_VTT_EN 203
+/* Touch screen controller to identify the LCD */
+#define OSD_TS_FT_BUS_ADDRESS 0
+#define OSD_TS_FT_CHIP_ADDRESS 0x38
+#define OSD_TS_FT_REG_ID 0xA3
+/*
+ * Touchscreen IDs for various OSD panels
+ * Ref: http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
+ */
+/* Used on newer osd101t2587 Panels */
+#define OSD_TS_FT_ID_5x46 0x54
+/* Used on older osd101t2045 Panels */
+#define OSD_TS_FT_ID_5606 0x08
+
#define SYSINFO_BOARD_NAME_MAX_LEN 45
+#define TPS65903X_PRIMARY_SECONDARY_PAD2 0xFB
+#define TPS65903X_PAD2_POWERHOLD_MASK 0x20
+
const struct omap_sysinfo sysinfo = {
"Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n"
};
.is_ma_present = 0x1
};
+static const struct dmm_lisa_map_regs am571x_idk_lisa_regs = {
+ .dmm_lisa_map_3 = 0x80640100,
+ .is_ma_present = 0x1
+};
+
void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
{
- *dmm_lisa_regs = &beagle_x15_lisa_regs;
+ if (board_is_am571x_idk())
+ *dmm_lisa_regs = &am571x_idk_lisa_regs;
+ else
+ *dmm_lisa_regs = &beagle_x15_lisa_regs;
}
static const struct emif_regs beagle_x15_emif1_ddr3_532mhz_emif_regs = {
.iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK,
};
+struct vcores_data am571x_idk_volts = {
+ .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM,
+ .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM,
+ .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .mpu.addr = TPS659038_REG_ADDR_SMPS12,
+ .mpu.pmic = &tps659038,
+ .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK,
+
+ .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM,
+ .eve.value[OPP_OD] = VDD_EVE_DRA7_OD,
+ .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH,
+ .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM,
+ .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD,
+ .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH,
+ .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .eve.addr = TPS659038_REG_ADDR_SMPS45,
+ .eve.pmic = &tps659038,
+ .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK,
+
+ .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM,
+ .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD,
+ .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH,
+ .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM,
+ .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD,
+ .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH,
+ .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .gpu.addr = TPS659038_REG_ADDR_SMPS6,
+ .gpu.pmic = &tps659038,
+ .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK,
+
+ .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM,
+ .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM,
+ .core.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .core.addr = TPS659038_REG_ADDR_SMPS7,
+ .core.pmic = &tps659038,
+
+ .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM,
+ .iva.value[OPP_OD] = VDD_IVA_DRA7_OD,
+ .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH,
+ .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM,
+ .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD,
+ .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH,
+ .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .iva.addr = TPS659038_REG_ADDR_SMPS45,
+ .iva.pmic = &tps659038,
+ .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK,
+};
+
int get_voltrail_opp(int rail_offset)
{
int opp;
bname = "AM572x EVM";
else if (board_is_am572x_idk())
bname = "AM572x IDK";
+ else if (board_is_am571x_idk())
+ bname = "AM571x IDK";
if (bname)
snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN,
if (rc)
goto invalid_eeprom;
- if (board_is_x15())
- name = "beagle_x15";
- else if (board_is_am572x_evm())
- name = "am57xx_evm";
- else if (board_is_am572x_idk())
+ if (board_is_x15()) {
+ if (board_is_x15_revb1())
+ name = "beagle_x15_revb1";
+ else if (board_is_x15_revc())
+ name = "beagle_x15_revc";
+ else
+ name = "beagle_x15";
+ } else if (board_is_am572x_evm()) {
+ if (board_is_am572x_evm_reva3())
+ name = "am57xx_evm_reva3";
+ else
+ name = "am57xx_evm";
+ } else if (board_is_am572x_idk()) {
name = "am572x_idk";
- else
+ } else if (board_is_am571x_idk()) {
+ name = "am571x_idk";
+ } else {
printf("Unidentified board claims %s in eeprom header\n",
board_ti_get_name());
+ }
invalid_eeprom:
set_board_info_env(name);
{
if (board_is_am572x_idk())
*omap_vcores = &am572x_idk_volts;
+ else if (board_is_am571x_idk())
+ *omap_vcores = &am571x_idk_volts;
else
*omap_vcores = &beagle_x15_volts;
}
*ctrl = &dra7xx_ctrl;
}
+bool am571x_idk_needs_lcd(void)
+{
+ bool needs_lcd;
+
+ gpio_request(GPIO_ETH_LCD, "nLCD_Detect");
+ if (gpio_get_value(GPIO_ETH_LCD))
+ needs_lcd = false;
+ else
+ needs_lcd = true;
+
+ gpio_free(GPIO_ETH_LCD);
+
+ return needs_lcd;
+}
+
int board_init(void)
{
gpmc_init();
return 0;
}
+void am57x_idk_lcd_detect(void)
+{
+ int r = -ENODEV;
+ char *idk_lcd = "no";
+ uint8_t buf = 0;
+
+ /* Only valid for IDKs */
+ if (board_is_x15() || board_is_am572x_evm())
+ return;
+
+ /* Only AM571x IDK has gpio control detect.. so check that */
+ if (board_is_am571x_idk() && !am571x_idk_needs_lcd())
+ goto out;
+
+ r = i2c_set_bus_num(OSD_TS_FT_BUS_ADDRESS);
+ if (r) {
+ printf("%s: Failed to set bus address to %d: %d\n",
+ __func__, OSD_TS_FT_BUS_ADDRESS, r);
+ goto out;
+ }
+ r = i2c_probe(OSD_TS_FT_CHIP_ADDRESS);
+ if (r) {
+ /* AM572x IDK has no explicit settings for optional LCD kit */
+ if (board_is_am571x_idk()) {
+ printf("%s: Touch screen detect failed: %d!\n",
+ __func__, r);
+ }
+ goto out;
+ }
+
+ /* Read FT ID */
+ r = i2c_read(OSD_TS_FT_CHIP_ADDRESS, OSD_TS_FT_REG_ID, 1, &buf, 1);
+ if (r) {
+ printf("%s: Touch screen ID read %d:0x%02x[0x%02x] failed:%d\n",
+ __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS,
+ OSD_TS_FT_REG_ID, r);
+ goto out;
+ }
+
+ switch (buf) {
+ case OSD_TS_FT_ID_5606:
+ idk_lcd = "osd101t2045";
+ break;
+ case OSD_TS_FT_ID_5x46:
+ idk_lcd = "osd101t2587";
+ break;
+ default:
+ printf("%s: Unidentifed Touch screen ID 0x%02x\n",
+ __func__, buf);
+ /* we will let default be "no lcd" */
+ }
+out:
+ env_set("idk_lcd", idk_lcd);
+ return;
+}
+
int board_late_init(void)
{
setup_board_eeprom_env();
+ u8 val;
/*
* DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds
* on HS devices.
*/
if (get_device_type() == HS_DEVICE)
- setenv("boot_fit", "1");
+ env_set("boot_fit", "1");
+
+ /*
+ * Set the GPIO7 Pad to POWERHOLD. This has higher priority
+ * over DEV_CTRL.DEV_ON bit. This can be reset in case of
+ * PMIC Power off. So to be on the safer side set it back
+ * to POWERHOLD mode irrespective of the current state.
+ */
+ palmas_i2c_read_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
+ &val);
+ val = val | TPS65903X_PAD2_POWERHOLD_MASK;
+ palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
+ val);
+
+ omap_die_id_serial();
+ omap_set_fastboot_vars();
+
+ am57x_idk_lcd_detect();
+
+#if !defined(CONFIG_SPL_BUILD)
+ board_ti_set_ethaddr(2);
+#endif
return 0;
}
void recalibrate_iodelay(void)
{
const struct pad_conf_entry *pconf;
- const struct iodelay_cfg_entry *iod;
- int pconf_sz, iod_sz;
+ const struct iodelay_cfg_entry *iod, *delta_iod;
+ int pconf_sz, iod_sz, delta_iod_sz = 0;
+ int ret;
if (board_is_am572x_idk()) {
pconf = core_padconf_array_essential_am572x_idk;
pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am572x_idk);
iod = iodelay_cfg_array_am572x_idk;
iod_sz = ARRAY_SIZE(iodelay_cfg_array_am572x_idk);
+ } else if (board_is_am571x_idk()) {
+ pconf = core_padconf_array_essential_am571x_idk;
+ pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am571x_idk);
+ iod = iodelay_cfg_array_am571x_idk;
+ iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk);
} else {
/* Common for X15/GPEVM */
pconf = core_padconf_array_essential_x15;
pconf_sz = ARRAY_SIZE(core_padconf_array_essential_x15);
- iod = iodelay_cfg_array_x15;
- iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15);
+ /* There never was an SR1.0 X15.. So.. */
+ if (omap_revision() == DRA752_ES1_1) {
+ iod = iodelay_cfg_array_x15_sr1_1;
+ iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr1_1);
+ } else {
+ /* Since full production should switch to SR2.0 */
+ iod = iodelay_cfg_array_x15_sr2_0;
+ iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr2_0);
+ }
}
- __recalibrate_iodelay(pconf, pconf_sz, iod, iod_sz);
+ /* Setup I/O isolation */
+ ret = __recalibrate_iodelay_start();
+ if (ret)
+ goto err;
+
+ /* Do the muxing here */
+ do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
+
+ /* Now do the weird minor deltas that should be safe */
+ if (board_is_x15() || board_is_am572x_evm()) {
+ if (board_is_x15_revb1() || board_is_am572x_evm_reva3() ||
+ board_is_x15_revc()) {
+ pconf = core_padconf_array_delta_x15_sr2_0;
+ pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr2_0);
+ } else {
+ pconf = core_padconf_array_delta_x15_sr1_1;
+ pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr1_1);
+ }
+ do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
+ }
+
+ if (board_is_am571x_idk()) {
+ if (am571x_idk_needs_lcd()) {
+ pconf = core_padconf_array_vout_am571x_idk;
+ pconf_sz = ARRAY_SIZE(core_padconf_array_vout_am571x_idk);
+ delta_iod = iodelay_cfg_array_am571x_idk_4port;
+ delta_iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk_4port);
+
+ } else {
+ pconf = core_padconf_array_icss1eth_am571x_idk;
+ pconf_sz = ARRAY_SIZE(core_padconf_array_icss1eth_am571x_idk);
+ }
+ do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
+ }
+
+ /* Setup IOdelay configuration */
+ ret = do_set_iodelay((*ctrl)->iodelay_config_base, iod, iod_sz);
+ if (delta_iod_sz)
+ ret = do_set_iodelay((*ctrl)->iodelay_config_base, delta_iod,
+ delta_iod_sz);
+
+err:
+ /* Closeup.. remove isolation */
+ __recalibrate_iodelay_end(ret);
}
#endif
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
+#if defined(CONFIG_MMC)
int board_mmc_init(bd_t *bis)
{
omap_mmc_init(0, 0, 0, -1, -1);
#ifdef CONFIG_SPL_ENV_SUPPORT
env_init();
- env_relocate_spec();
- if (getenv_yesno("boot_os") != 1)
+ env_load();
+ if (env_get_yesno("boot_os") != 1)
return 1;
#endif
#endif /* CONFIG_USB_DWC3 */
#if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP)
-int board_usb_init(int index, enum usb_init_type init)
+int omap_xhci_board_usb_init(int index, enum usb_init_type init)
{
enable_usb_clocks(index);
switch (index) {
return 0;
}
-int board_usb_cleanup(int index, enum usb_init_type init)
+int omap_xhci_board_usb_cleanup(int index, enum usb_init_type init)
{
#ifdef CONFIG_USB_DWC3
switch (index) {
mac_addr[4] = (mac_lo & 0xFF00) >> 8;
mac_addr[5] = mac_lo & 0xFF;
- if (!getenv("ethaddr")) {
+ if (!env_get("ethaddr")) {
printf("<ethaddr> not set. Validating first E-fuse MAC\n");
if (is_valid_ethaddr(mac_addr))
- eth_setenv_enetaddr("ethaddr", mac_addr);
+ eth_env_set_enetaddr("ethaddr", mac_addr);
}
mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
mac_addr[4] = (mac_lo & 0xFF00) >> 8;
mac_addr[5] = mac_lo & 0xFF;
- if (!getenv("eth1addr")) {
+ if (!env_get("eth1addr")) {
if (is_valid_ethaddr(mac_addr))
- eth_setenv_enetaddr("eth1addr", mac_addr);
+ eth_env_set_enetaddr("eth1addr", mac_addr);
}
ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
ctrl_val |= 0x22;
writel(ctrl_val, (*ctrl)->control_core_control_io1);
- /* The phy address for the AM572x IDK are different than x15 */
- if (board_is_am572x_idk()) {
+ /* The phy address for the AM57xx IDK are different than x15 */
+ if (board_is_am572x_idk() || board_is_am571x_idk()) {
cpsw_data.slave_data[0].phy_addr = 0;
cpsw_data.slave_data[1].phy_addr = 1;
}
for (i = 0; i < num_macs; i++) {
u64_to_mac(mac1 + i, mac_addr);
if (is_valid_ethaddr(mac_addr)) {
- eth_setenv_enetaddr_by_index("eth",
- i + 2,
- mac_addr);
+ eth_env_set_enetaddr_by_index("eth",
+ i + 2,
+ mac_addr);
}
}
}
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
- if (board_is_x15() && !strcmp(name, "am57xx-beagle-x15"))
+ if (board_is_x15()) {
+ if (board_is_x15_revb1()) {
+ if (!strcmp(name, "am57xx-beagle-x15-revb1"))
+ return 0;
+ } else if (!strcmp(name, "am57xx-beagle-x15")) {
+ return 0;
+ }
+ } else if (board_is_am572x_evm() &&
+ !strcmp(name, "am57xx-beagle-x15")) {
return 0;
- else if (board_is_am572x_evm() && !strcmp(name, "am57xx-beagle-x15"))
+ } else if (board_is_am572x_idk() && !strcmp(name, "am572x-idk")) {
return 0;
- else if (board_is_am572x_idk() && !strcmp(name, "am572x-idk"))
+ } else if (board_is_am571x_idk() && !strcmp(name, "am571x-idk")) {
return 0;
- else
- return -1;
+ }
+
+ return -1;
}
#endif