#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
+#include <asm/omap_musb.h>
+#include <asm/errno.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
#include "beagle.h"
#include <command.h>
#define BBTOYS_LCD 0x03000B00
#define BCT_BRETTL3 0x01000F00
#define BCT_BRETTL4 0x02000F00
+#define LSR_COM6L_ADPT 0x01001300
#define BEAGLE_NO_EEPROM 0xffffffff
DECLARE_GLOBAL_DATA_PTR;
i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 1, (u8 *)&expansion_config,
sizeof(expansion_config));
+ /* retry reading configuration data with 16bit addressing */
+ if ((expansion_config.device_vendor == 0xFFFFFF00) ||
+ (expansion_config.device_vendor == 0xFFFFFFFF)) {
+ printf("EEPROM is blank or 8bit addressing failed: retrying with 16bit:\n");
+ i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 2, (u8 *)&expansion_config,
+ sizeof(expansion_config));
+ }
+
i2c_set_bus_num(TWL4030_I2C_BUS);
return expansion_config.device_vendor;
}
#endif
+#ifdef CONFIG_USB_MUSB_OMAP2PLUS
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .num_eps = 16,
+ .ram_bits = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+ .interface_type = MUSB_INTERFACE_ULPI,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_MUSB_HOST)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_MUSB_GADGET)
+ .mode = MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_MUSB_HOST or CONFIG_MUSB_GADGET"
+#endif
+ .config = &musb_config,
+ .power = 100,
+ .platform_ops = &omap2430_ops,
+ .board_data = &musb_board_data,
+};
+#endif
+
/*
* Routine: misc_init_r
* Description: Configure board specific parts
case BCT_BRETTL4:
printf("Recognized bct electronic GmbH brettl4 board\n");
break;
+ case LSR_COM6L_ADPT:
+ printf("Recognized LSR COM6L Adapter Board\n");
+ MUX_BBTOYS_WIFI()
+ setenv("buddy", "lsr-com6l-adpt");
+ break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy", "none");
omap3_dss_enable();
#endif
+#ifdef CONFIG_USB_MUSB_OMAP2PLUS
+ musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
+#endif
+
return 0;
}
#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
int board_mmc_init(bd_t *bis)
{
- omap_mmc_init(0, 0, 0);
- return 0;
+ return omap_mmc_init(0, 0, 0, -1, -1);
}
#endif
}
#endif /* CONFIG_USB_EHCI */
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)
+int board_eth_init(bd_t *bis)
+{
+ return usb_eth_initialize(bis);
+}
+#endif