#include <common.h>
#include <dm.h>
#include <ns16550.h>
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#include <status_led.h>
#endif
#include <twl4030.h>
-#include <linux/mtd/nand.h>
+#include <linux/mtd/rawnand.h>
#include <asm/io.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/omap_musb.h>
-#include <asm/errno.h>
+#include <linux/errno.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/musb.h>
#include "beagle.h"
#include <command.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
} expansion_config;
static const struct ns16550_platdata beagle_serial = {
- OMAP34XX_UART3,
- 2,
- V_NS16550_CLK
+ .base = OMAP34XX_UART3,
+ .reg_shift = 2,
+ .clock = V_NS16550_CLK,
+ .fcr = UART_FCR_DEFVAL,
};
U_BOOT_DEVICE(beagle_uart) = {
- "serial_omap",
+ "ns16550_serial",
&beagle_serial
};
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
#endif
return 0;
switch (get_board_revision()) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
- setenv("beaglerev", "AxBx");
+ env_set("beaglerev", "AxBx");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
- setenv("beaglerev", "Cx");
+ env_set("beaglerev", "Cx");
MUX_BEAGLE_C();
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
- setenv("beaglerev", "C4");
+ env_set("beaglerev", "C4");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
break;
case REVISION_XM_AB:
printf("Beagle xM Rev A/B\n");
- setenv("beaglerev", "xMAB");
+ env_set("beaglerev", "xMAB");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
break;
case REVISION_XM_C:
printf("Beagle xM Rev C\n");
- setenv("beaglerev", "xMC");
+ env_set("beaglerev", "xMC");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
- setenv("buddy", "zippy");
+ env_set("buddy", "zippy");
break;
case TINCANTOOLS_ZIPPY2:
printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
- setenv("buddy", "zippy2");
+ env_set("buddy", "zippy2");
break;
case TINCANTOOLS_TRAINER:
printf("Recognized Tincantools Trainer board (rev %d %s)\n",
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
MUX_TINCANTOOLS_TRAINER();
- setenv("buddy", "trainer");
+ env_set("buddy", "trainer");
break;
case TINCANTOOLS_SHOWDOG:
printf("Recognized Tincantools Showdow board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
/* Place holder for DSS2 definition for showdog lcd */
- setenv("defaultdisplay", "showdoglcd");
- setenv("buddy", "showdog");
+ env_set("defaultdisplay", "showdoglcd");
+ env_set("buddy", "showdog");
break;
case KBADC_BEAGLEFPGA:
printf("Recognized KBADC Beagle FPGA board\n");
MUX_KBADC_BEAGLEFPGA();
- setenv("buddy", "beaglefpga");
+ env_set("buddy", "beaglefpga");
break;
case LW_BEAGLETOUCH:
printf("Recognized Liquidware BeagleTouch board\n");
- setenv("buddy", "beagletouch");
+ env_set("buddy", "beagletouch");
break;
case BRAINMUX_LCDOG:
printf("Recognized Brainmux LCDog board\n");
- setenv("buddy", "lcdog");
+ env_set("buddy", "lcdog");
break;
case BRAINMUX_LCDOGTOUCH:
printf("Recognized Brainmux LCDog Touch board\n");
- setenv("buddy", "lcdogtouch");
+ env_set("buddy", "lcdogtouch");
break;
case BBTOYS_WIFI:
printf("Recognized BeagleBoardToys WiFi board\n");
MUX_BBTOYS_WIFI()
- setenv("buddy", "bbtoys-wifi");
- break;;
+ env_set("buddy", "bbtoys-wifi");
+ break;
case BBTOYS_VGA:
printf("Recognized BeagleBoardToys VGA board\n");
- break;;
+ break;
case BBTOYS_LCD:
printf("Recognized BeagleBoardToys LCD board\n");
- break;;
+ break;
case BCT_BRETTL3:
printf("Recognized bct electronic GmbH brettl3 board\n");
break;
case LSR_COM6L_ADPT:
printf("Recognized LSR COM6L Adapter Board\n");
MUX_BBTOYS_WIFI()
- setenv("buddy", "lsr-com6l-adpt");
+ env_set("buddy", "lsr-com6l-adpt");
break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
- setenv("buddy", "none");
+ env_set("buddy", "none");
break;
default:
printf("Unrecognized expansion board: %x\n",
expansion_config.device_vendor);
- setenv("buddy", "unknown");
+ env_set("buddy", "unknown");
}
if (expansion_config.content == 1)
- setenv(expansion_config.env_var, expansion_config.env_setting);
+ env_set(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
switch (get_board_revision()) {
MUX_BEAGLE();
}
-#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_MMC)
int board_mmc_init(bd_t *bis)
{
return omap_mmc_init(0, 0, 0, -1, -1);
}
#endif
-#if defined(CONFIG_GENERIC_MMC)
+#if defined(CONFIG_MMC)
void board_mmc_power_init(void)
{
twl4030_power_mmc_init(0);
}
#endif
-#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
int board_eth_init(bd_t *bis)
projects / u-boot / blobdiff