#include <common.h>
#include <mpc5xxx.h>
#include <pci.h>
+#include <netdev.h>
#include "sdram.h"
#include "mt48lc16m16a2-75.h"
#endif
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
sdram_conf_t sdram_conf;
sdram_conf.control = SDRAM_CONTROL;
sdram_conf.config1 = SDRAM_CONFIG1;
sdram_conf.config2 = SDRAM_CONFIG2;
-#if defined(CONFIG_MPC5200)
sdram_conf.tapdelay = 0;
-#endif
-#if defined(CONFIG_MGT5100)
- sdram_conf.addrsel = SDRAM_ADDRSEL;
-#endif
return mpc5xxx_sdram_init (&sdram_conf);
}
int checkboard (void)
{
-#if defined(CONFIG_MPC5200)
#if CONFIG_TOTAL5200_REV==2
puts ("Board: Total5200 Rev.2 ");
#else
puts ("Board: Total5200 ");
#endif
-#elif defined(CONFIG_MGT5100)
- puts ("Board: Total5100 ");
-#endif
-/*
- * Retrieve FPGA Revision.
- */
-printf ("(FPGA %08X)\n", *(vu_long *) (CFG_FPGA_BASE + 0x400));
+ /*
+ * Retrieve FPGA Revision.
+ */
+ printf ("(FPGA %08lX)\n", *(vu_long *) (CONFIG_SYS_FPGA_BASE + 0x400));
-/*
- * Take all peripherals in power-up mode.
- */
+ /*
+ * Take all peripherals in power-up mode.
+ */
#if CONFIG_TOTAL5200_REV==2
- *(vu_char *) (CFG_CPLD_BASE + 0x46) = 0x70;
+ *(vu_char *) (CONFIG_SYS_CPLD_BASE + 0x46) = 0x70;
#else
- *(vu_long *) (CFG_CPLD_BASE + 0x400) = 0x70;
+ *(vu_long *) (CONFIG_SYS_CPLD_BASE + 0x400) = 0x70;
#endif
return 0;
}
-#if defined(CONFIG_MGT5100)
-int board_early_init_r(void)
-{
- /*
- * Now, when we are in RAM, enable CS0
- * because CS_BOOT cannot be written.
- */
- *(vu_long *)MPC5XXX_ADDECR &= ~(1 << 25); /* disable CS_BOOT */
- *(vu_long *)MPC5XXX_ADDECR |= (1 << 16); /* enable CS0 */
-
- return 0;
-}
-#endif
-
#ifdef CONFIG_PCI
static struct pci_controller hose;
}
#endif
-#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
/* IRDA_1 aka PSC6_3 (pin C13) */
#define GPIO_IRDA_1 0x20000000UL
{
debug ("init_ide_reset\n");
- /* Configure IRDA_1 (PSC6_3) as GPIO output for ATA reset */
+ /* Configure IRDA_1 (PSC6_3) as GPIO output for ATA reset */
*(vu_long *) MPC5XXX_GPIO_ENABLE |= GPIO_IRDA_1;
*(vu_long *) MPC5XXX_GPIO_DIR |= GPIO_IRDA_1;
}
*(vu_long *) MPC5XXX_GPIO_DATA_O |= GPIO_IRDA_1;
}
}
-#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */
+#endif
+
+#ifdef CONFIG_VIDEO_SED13806
+#include <sed13806.h>
+
+#define DISPLAY_WIDTH 640
+#define DISPLAY_HEIGHT 480
+
+#ifdef CONFIG_VIDEO_SED13806_8BPP
+#error CONFIG_VIDEO_SED13806_8BPP not supported.
+#endif /* CONFIG_VIDEO_SED13806_8BPP */
+
+#ifdef CONFIG_VIDEO_SED13806_16BPP
+static const S1D_REGS init_regs [] =
+{
+ {0x0001,0x00}, /* Miscellaneous Register */
+ {0x01FC,0x00}, /* Display Mode Register */
+ {0x0004,0x00}, /* General IO Pins Configuration Register 0 */
+ {0x0005,0x00}, /* General IO Pins Configuration Register 1 */
+ {0x0008,0x00}, /* General IO Pins Control Register 0 */
+ {0x0009,0x00}, /* General IO Pins Control Register 1 */
+ {0x0010,0x02}, /* Memory Clock Configuration Register */
+ {0x0014,0x02}, /* LCD Pixel Clock Configuration Register */
+ {0x0018,0x02}, /* CRT/TV Pixel Clock Configuration Register */
+ {0x001C,0x02}, /* MediaPlug Clock Configuration Register */
+ {0x001E,0x01}, /* CPU To Memory Wait State Select Register */
+ {0x0021,0x03}, /* DRAM Refresh Rate Register */
+ {0x002A,0x00}, /* DRAM Timings Control Register 0 */
+ {0x002B,0x01}, /* DRAM Timings Control Register 1 */
+ {0x0020,0x80}, /* Memory Configuration Register */
+ {0x0030,0x25}, /* Panel Type Register */
+ {0x0031,0x00}, /* MOD Rate Register */
+ {0x0032,0x4F}, /* LCD Horizontal Display Width Register */
+ {0x0034,0x13}, /* LCD Horizontal Non-Display Period Register */
+ {0x0035,0x01}, /* TFT FPLINE Start Position Register */
+ {0x0036,0x0B}, /* TFT FPLINE Pulse Width Register */
+ {0x0038,0xDF}, /* LCD Vertical Display Height Register 0 */
+ {0x0039,0x01}, /* LCD Vertical Display Height Register 1 */
+ {0x003A,0x2C}, /* LCD Vertical Non-Display Period Register */
+ {0x003B,0x0A}, /* TFT FPFRAME Start Position Register */
+ {0x003C,0x01}, /* TFT FPFRAME Pulse Width Register */
+ {0x0040,0x05}, /* LCD Display Mode Register */
+ {0x0041,0x00}, /* LCD Miscellaneous Register */
+ {0x0042,0x00}, /* LCD Display Start Address Register 0 */
+ {0x0043,0x00}, /* LCD Display Start Address Register 1 */
+ {0x0044,0x00}, /* LCD Display Start Address Register 2 */
+ {0x0046,0x80}, /* LCD Memory Address Offset Register 0 */
+ {0x0047,0x02}, /* LCD Memory Address Offset Register 1 */
+ {0x0048,0x00}, /* LCD Pixel Panning Register */
+ {0x004A,0x00}, /* LCD Display FIFO High Threshold Control Register */
+ {0x004B,0x00}, /* LCD Display FIFO Low Threshold Control Register */
+ {0x0050,0x4F}, /* CRT/TV Horizontal Display Width Register */
+ {0x0052,0x13}, /* CRT/TV Horizontal Non-Display Period Register */
+ {0x0053,0x01}, /* CRT/TV HRTC Start Position Register */
+ {0x0054,0x0B}, /* CRT/TV HRTC Pulse Width Register */
+ {0x0056,0xDF}, /* CRT/TV Vertical Display Height Register 0 */
+ {0x0057,0x01}, /* CRT/TV Vertical Display Height Register 1 */
+ {0x0058,0x2B}, /* CRT/TV Vertical Non-Display Period Register */
+ {0x0059,0x09}, /* CRT/TV VRTC Start Position Register */
+ {0x005A,0x01}, /* CRT/TV VRTC Pulse Width Register */
+ {0x005B,0x10}, /* TV Output Control Register */
+ {0x0060,0x05}, /* CRT/TV Display Mode Register */
+ {0x0062,0x00}, /* CRT/TV Display Start Address Register 0 */
+ {0x0063,0x00}, /* CRT/TV Display Start Address Register 1 */
+ {0x0064,0x00}, /* CRT/TV Display Start Address Register 2 */
+ {0x0066,0x80}, /* CRT/TV Memory Address Offset Register 0 */
+ {0x0067,0x02}, /* CRT/TV Memory Address Offset Register 1 */
+ {0x0068,0x00}, /* CRT/TV Pixel Panning Register */
+ {0x006A,0x00}, /* CRT/TV Display FIFO High Threshold Control Register */
+ {0x006B,0x00}, /* CRT/TV Display FIFO Low Threshold Control Register */
+ {0x0070,0x00}, /* LCD Ink/Cursor Control Register */
+ {0x0071,0x01}, /* LCD Ink/Cursor Start Address Register */
+ {0x0072,0x00}, /* LCD Cursor X Position Register 0 */
+ {0x0073,0x00}, /* LCD Cursor X Position Register 1 */
+ {0x0074,0x00}, /* LCD Cursor Y Position Register 0 */
+ {0x0075,0x00}, /* LCD Cursor Y Position Register 1 */
+ {0x0076,0x00}, /* LCD Ink/Cursor Blue Color 0 Register */
+ {0x0077,0x00}, /* LCD Ink/Cursor Green Color 0 Register */
+ {0x0078,0x00}, /* LCD Ink/Cursor Red Color 0 Register */
+ {0x007A,0x1F}, /* LCD Ink/Cursor Blue Color 1 Register */
+ {0x007B,0x3F}, /* LCD Ink/Cursor Green Color 1 Register */
+ {0x007C,0x1F}, /* LCD Ink/Cursor Red Color 1 Register */
+ {0x007E,0x00}, /* LCD Ink/Cursor FIFO Threshold Register */
+ {0x0080,0x00}, /* CRT/TV Ink/Cursor Control Register */
+ {0x0081,0x01}, /* CRT/TV Ink/Cursor Start Address Register */
+ {0x0082,0x00}, /* CRT/TV Cursor X Position Register 0 */
+ {0x0083,0x00}, /* CRT/TV Cursor X Position Register 1 */
+ {0x0084,0x00}, /* CRT/TV Cursor Y Position Register 0 */
+ {0x0085,0x00}, /* CRT/TV Cursor Y Position Register 1 */
+ {0x0086,0x00}, /* CRT/TV Ink/Cursor Blue Color 0 Register */
+ {0x0087,0x00}, /* CRT/TV Ink/Cursor Green Color 0 Register */
+ {0x0088,0x00}, /* CRT/TV Ink/Cursor Red Color 0 Register */
+ {0x008A,0x1F}, /* CRT/TV Ink/Cursor Blue Color 1 Register */
+ {0x008B,0x3F}, /* CRT/TV Ink/Cursor Green Color 1 Register */
+ {0x008C,0x1F}, /* CRT/TV Ink/Cursor Red Color 1 Register */
+ {0x008E,0x00}, /* CRT/TV Ink/Cursor FIFO Threshold Register */
+ {0x0100,0x00}, /* BitBlt Control Register 0 */
+ {0x0101,0x00}, /* BitBlt Control Register 1 */
+ {0x0102,0x00}, /* BitBlt ROP Code/Color Expansion Register */
+ {0x0103,0x00}, /* BitBlt Operation Register */
+ {0x0104,0x00}, /* BitBlt Source Start Address Register 0 */
+ {0x0105,0x00}, /* BitBlt Source Start Address Register 1 */
+ {0x0106,0x00}, /* BitBlt Source Start Address Register 2 */
+ {0x0108,0x00}, /* BitBlt Destination Start Address Register 0 */
+ {0x0109,0x00}, /* BitBlt Destination Start Address Register 1 */
+ {0x010A,0x00}, /* BitBlt Destination Start Address Register 2 */
+ {0x010C,0x00}, /* BitBlt Memory Address Offset Register 0 */
+ {0x010D,0x00}, /* BitBlt Memory Address Offset Register 1 */
+ {0x0110,0x00}, /* BitBlt Width Register 0 */
+ {0x0111,0x00}, /* BitBlt Width Register 1 */
+ {0x0112,0x00}, /* BitBlt Height Register 0 */
+ {0x0113,0x00}, /* BitBlt Height Register 1 */
+ {0x0114,0x00}, /* BitBlt Background Color Register 0 */
+ {0x0115,0x00}, /* BitBlt Background Color Register 1 */
+ {0x0118,0x00}, /* BitBlt Foreground Color Register 0 */
+ {0x0119,0x00}, /* BitBlt Foreground Color Register 1 */
+ {0x01E0,0x00}, /* Look-Up Table Mode Register */
+ {0x01E2,0x00}, /* Look-Up Table Address Register */
+ {0x01E4,0x00}, /* Look-Up Table Data Register */
+ {0x01F0,0x00}, /* Power Save Configuration Register */
+ {0x01F1,0x00}, /* Power Save Status Register */
+ {0x01F4,0x00}, /* CPU-to-Memory Access Watchdog Timer Register */
+ {0x01FC,0x01}, /* Display Mode Register */
+ {0, 0}
+};
+#endif /* CONFIG_VIDEO_SED13806_16BPP */
+
+#ifdef CONFIG_CONSOLE_EXTRA_INFO
+/* Return text to be printed besides the logo. */
+void video_get_info_str (int line_number, char *info)
+{
+ if (line_number == 1) {
+#if CONFIG_TOTAL5200_REV==1
+ strcpy (info, " Total5200");
+#elif CONFIG_TOTAL5200_REV==2
+ strcpy (info, " Total5200 Rev.2");
+#else
+#error CONFIG_TOTAL5200_REV must be 1 or 2.
+#endif
+ } else {
+ info [0] = '\0';
+ }
+}
+#endif
+
+/* Returns SED13806 base address. First thing called in the driver. */
+unsigned int board_video_init (void)
+{
+ return CONFIG_SYS_LCD_BASE;
+}
+
+/* Called after initializing the SED13806 and before clearing the screen. */
+void board_validate_screen (unsigned int base)
+{
+}
+
+/* Return a pointer to the initialization sequence. */
+const S1D_REGS *board_get_regs (void)
+{
+ return init_regs;
+}
+
+int board_get_width (void)
+{
+ return DISPLAY_WIDTH;
+}
+
+int board_get_height (void)
+{
+ return DISPLAY_HEIGHT;
+}
+
+#endif /* CONFIG_VIDEO_SED13806 */
+
+int board_eth_init(bd_t *bis)
+{
+ cpu_eth_init(bis); /* Built in FEC comes first */
+ return pci_eth_init(bis);
+}
projects / u-boot / blobdiff