struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR, CFG_INIT_RAM_ADDR,
+ SET_TLB_ENTRY (0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR + 4 * 1024,
- CFG_INIT_RAM_ADDR + 4 * 1024,
+ SET_TLB_ENTRY (0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR + 8 * 1024,
- CFG_INIT_RAM_ADDR + 8 * 1024,
+ SET_TLB_ENTRY (0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR + 12 * 1024,
- CFG_INIT_RAM_ADDR + 12 * 1024,
+ SET_TLB_ENTRY (0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
+#ifndef CONFIG_TQM_BIGFLASH
/*
* TLB 0, 1: 128M Non-cacheable, guarded
* 0xf8000000 128M FLASH
* Out of reset this entry is only 4K.
*/
- SET_TLB_ENTRY (1, CFG_FLASH_BASE, CFG_FLASH_BASE,
+ SET_TLB_ENTRY (1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 1, BOOKE_PAGESZ_64M, 1),
- SET_TLB_ENTRY (1, CFG_FLASH_BASE + 0x4000000,
- CFG_FLASH_BASE + 0x4000000,
+ SET_TLB_ENTRY (1, CONFIG_SYS_FLASH_BASE + 0x4000000,
+ CONFIG_SYS_FLASH_BASE + 0x4000000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 0, BOOKE_PAGESZ_64M, 1),
* TLB 2: 256M Non-cacheable, guarded
* 0x80000000 256M PCI1 MEM First half
*/
- SET_TLB_ENTRY (1, CFG_PCI1_MEM_PHYS, CFG_PCI1_MEM_PHYS,
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
* TLB 3: 256M Non-cacheable, guarded
* 0x90000000 256M PCI1 MEM Second half
*/
- SET_TLB_ENTRY (1, CFG_PCI1_MEM_PHYS + 0x10000000,
- CFG_PCI1_MEM_PHYS + 0x10000000,
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
+ CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 3, BOOKE_PAGESZ_256M, 1),
+#ifdef CONFIG_PCIE1
+ /*
+ * TLB 4: 256M Non-cacheable, guarded
+ * 0xc0000000 256M PCI express MEM First half
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCIE1_MEM_BASE, CONFIG_SYS_PCIE1_MEM_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ /*
+ * TLB 5: 256M Non-cacheable, guarded
+ * 0xd0000000 256M PCI express MEM Second half
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCIE1_MEM_BASE + 0x10000000,
+ CONFIG_SYS_PCIE1_MEM_BASE + 0x10000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+#else /* !CONFIG_PCIE */
/*
* TLB 4: 256M Non-cacheable, guarded
* 0xc0000000 256M Rapid IO MEM First half
*/
- SET_TLB_ENTRY (1, CFG_RIO_MEM_BASE, CFG_RIO_MEM_BASE,
+ SET_TLB_ENTRY (1, CONFIG_SYS_RIO_MEM_BASE, CONFIG_SYS_RIO_MEM_BASE,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 4, BOOKE_PAGESZ_256M, 1),
* TLB 5: 256M Non-cacheable, guarded
* 0xd0000000 256M Rapid IO MEM Second half
*/
- SET_TLB_ENTRY (1, CFG_RIO_MEM_BASE + 0x10000000,
- CFG_RIO_MEM_BASE + 0x10000000,
+ SET_TLB_ENTRY (1, CONFIG_SYS_RIO_MEM_BASE + 0x10000000,
+ CONFIG_SYS_RIO_MEM_BASE + 0x10000000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 5, BOOKE_PAGESZ_256M, 1),
+#endif /* CONFIG_PCIE */
/*
* TLB 6: 64M Non-cacheable, guarded
* 0xe0000000 1M CCSRBAR
* 0xe2000000 16M PCI1 IO
- * 0xe3000000 16M CAN
+ * 0xe3000000 16M CAN and NAND Flash
*/
- SET_TLB_ENTRY (1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
+ SET_TLB_ENTRY (1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 6, BOOKE_PAGESZ_64M, 1),
+#if defined(CONFIG_TQM8548_AG) || defined (CONFIG_TQM8548_BE)
+ /*
+ * TLB 7+8: 2G DDR, cache enabled
+ * 0x00000000 2G DDR System memory
+ * Without SPD EEPROM configured DDR, this must be setup manually.
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_1G, 1),
+
+ SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 8, BOOKE_PAGESZ_1G, 1),
+#else
/*
* TLB 7+8: 512M DDR, cache disabled (needed for memory test)
* 0x00000000 512M DDR System memory
* Without SPD EEPROM configured DDR, this must be setup manually.
- * Make sure the TLB count at the top of this table is correct.
- * Likely it needs to be increased by two for these entries.
*/
- SET_TLB_ENTRY (1, CFG_DDR_SDRAM_BASE, CFG_DDR_SDRAM_BASE,
+ SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 7, BOOKE_PAGESZ_256M, 1),
- SET_TLB_ENTRY (1, CFG_DDR_SDRAM_BASE + 0x10000000,
- CFG_DDR_SDRAM_BASE + 0x10000000,
+ SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 8, BOOKE_PAGESZ_256M, 1),
+#endif
+#ifdef CONFIG_PCIE1
+ /*
+ * TLB 9: 16M Non-cacheable, guarded
+ * 0xef000000 16M PCI express IO
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCIE1_IO_BASE, CONFIG_SYS_PCIE1_IO_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 9, BOOKE_PAGESZ_16M, 1),
+#endif /* CONFIG_PCIE */
+
+#else /* CONFIG_TQM_BIGFLASH */
+
+ /*
+ * TLB 0,1,2,3: 1G Non-cacheable, guarded
+ * 0xc0000000 1G FLASH
+ * Out of reset this entry is only 4K.
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 3, BOOKE_PAGESZ_256M, 1),
+ SET_TLB_ENTRY (1, CONFIG_SYS_FLASH_BASE + 0x10000000,
+ CONFIG_SYS_FLASH_BASE + 0x10000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+ SET_TLB_ENTRY (1, CONFIG_SYS_FLASH_BASE + 0x20000000,
+ CONFIG_SYS_FLASH_BASE + 0x20000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 1, BOOKE_PAGESZ_256M, 1),
+ SET_TLB_ENTRY (1, CONFIG_SYS_FLASH_BASE + 0x30000000,
+ CONFIG_SYS_FLASH_BASE + 0x30000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256M, 1),
+
+ /*
+ * TLB 4: 256M Non-cacheable, guarded
+ * 0x80000000 256M PCI1 MEM First half
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ /*
+ * TLB 5: 256M Non-cacheable, guarded
+ * 0x90000000 256M PCI1 MEM Second half
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
+ CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+#ifdef CONFIG_PCIE1
+ /*
+ * TLB 6: 256M Non-cacheable, guarded
+ * 0xc0000000 256M PCI express MEM First half
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCIE1_MEM_BASE, CONFIG_SYS_PCIE1_MEM_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+#else /* !CONFIG_PCIE */
+ /*
+ * TLB 6: 256M Non-cacheable, guarded
+ * 0xb0000000 256M Rapid IO MEM First half
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_RIO_MEM_BASE, CONFIG_SYS_RIO_MEM_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+
+#endif /* CONFIG_PCIE */
+
+ /*
+ * TLB 7: 64M Non-cacheable, guarded
+ * 0xa0000000 1M CCSRBAR
+ * 0xa2000000 16M PCI1 IO
+ * 0xa3000000 16M CAN and NAND Flash
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 7, BOOKE_PAGESZ_64M, 1),
+
+ /*
+ * TLB 8+9: 512M DDR, cache disabled (needed for memory test)
+ * 0x00000000 512M DDR System memory
+ * Without SPD EEPROM configured DDR, this must be setup manually.
+ * Make sure the TLB count at the top of this table is correct.
+ * Likely it needs to be increased by two for these entries.
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 8, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY (1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 9, BOOKE_PAGESZ_256M, 1),
+
+#ifdef CONFIG_PCIE1
+ /*
+ * TLB 10: 16M Non-cacheable, guarded
+ * 0xaf000000 16M PCI express IO
+ */
+ SET_TLB_ENTRY (1, CONFIG_SYS_PCIE1_IO_BASE, CONFIG_SYS_PCIE1_IO_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 10, BOOKE_PAGESZ_16M, 1),
+#endif /* CONFIG_PCIE */
+
+#endif /* CONFIG_TQM_BIGFLASH */
};
int num_tlb_entries = ARRAY_SIZE (tlb_table);
projects / u-boot / blobdiff