#define REBOOT_NOP 0x00000000
#define REBOOT_DO_POST 0x00000001
-extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
extern env_t *env_ptr;
extern uchar default_environment[];
ulong flash_get_size(ulong base, int banknum);
void env_crc_update(void);
-int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]);
static u32 start_time;
int board_early_init_f(void)
{
- mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr(uicer, 0x00000000); /* disable all ints */
- mtdcr(uiccr, 0x00000000);
- mtdcr(uicpr, 0xFFFF7F00); /* set int polarities */
- mtdcr(uictr, 0x00000000); /* set int trigger levels */
- mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr(uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0ER, 0x00000000); /* disable all ints */
+ mtdcr(UIC0CR, 0x00000000);
+ mtdcr(UIC0PR, 0xFFFF7F00); /* set int polarities */
+ mtdcr(UIC0TR, 0x00000000); /* set int trigger levels */
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
/*
* Configure CPC0_PCI to enable PerWE as output
*/
- mtdcr(cpc0_pci, CPC0_PCI_SPE);
+ mtdcr(CPC0_PCI, CPC0_PCI_SPE);
return 0;
}
u32 post_magic;
u32 post_val;
- post_magic = in_be32((void *)CFG_POST_MAGIC);
- post_val = in_be32((void *)CFG_POST_VAL);
+ post_magic = in_be32((void *)CONFIG_SYS_POST_MAGIC);
+ post_val = in_be32((void *)CONFIG_SYS_POST_VAL);
if ((post_magic == REBOOT_MAGIC) && (post_val == REBOOT_DO_POST)) {
/*
* Set special bootline bootparameter to pass this POST boot
* via the sw-reset button. So disable further tests
* upon next bootup here.
*/
- out_be32((void *)CFG_POST_VAL, REBOOT_NOP);
+ out_be32((void *)CONFIG_SYS_POST_VAL, REBOOT_NOP);
} else {
/*
* Only run POST when initiated via the sw-reset button mechanism
/* Re-do sizing to get full correct info */
/* adjust flash start and offset */
- mfebc(pb0cr, pbcr);
+ mfebc(PB0CR, pbcr);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtebc(pb0cr, pbcr);
+ mtebc(PB0CR, pbcr);
/*
* Re-check to get correct base address
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- -CFG_MONITOR_LEN,
+ -CONFIG_SYS_MONITOR_LEN,
0xffffffff,
&flash_info[0]);
/* Env protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
+ CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
&flash_info[0]);
return 0;
puts("Board: Zeus-");
- if (in_be32((void *)GPIO0_IR) & GPIO_VAL(CFG_GPIO_ZEUS_PE))
+ if (in_be32((void *)GPIO0_IR) & GPIO_VAL(CONFIG_SYS_GPIO_ZEUS_PE))
puts("PE");
else
puts("CE");
putc('\n');
/* both LED's off */
- gpio_write_bit(CFG_GPIO_LED_RED, 0);
- gpio_write_bit(CFG_GPIO_LED_GREEN, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_RED, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_GREEN, 0);
udelay(10000);
/* and on again */
- gpio_write_bit(CFG_GPIO_LED_RED, 1);
- gpio_write_bit(CFG_GPIO_LED_GREEN, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_RED, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_GREEN, 1);
return (0);
}
char *buf_save;
u32 crc;
- /*
- * Unprotect and erase environment area
- */
- flash_protect(FLAG_PROTECT_CLEAR,
- CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
- &flash_info[0]);
+ set_default_env("");
- flash_sect_erase(CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1);
-
- /*
- * Now restore default environment from U-Boot image
- * -> ipaddr, serverip...
- */
- memset(env_ptr, 0, sizeof(env_t));
- memcpy(env_ptr->data, default_environment, ENV_SIZE);
-#ifdef CFG_REDUNDAND_ENVIRONMENT
- env_ptr->flags = 0xFF;
-#endif
- env_crc_update();
gd->env_valid = 1;
/*
* -> ethaddr, eth1addr, serial#
*/
buf = buf_save = malloc(FACTORY_RESET_ENV_SIZE);
+ if (buf == NULL) {
+ printf("ERROR: malloc() failed\n");
+ return -1;
+ }
if (eeprom_read(FACTORY_RESET_I2C_EEPROM, FACTORY_RESET_ENV_OFFS,
(u8 *)buf, FACTORY_RESET_ENV_SIZE)) {
puts("\nError reading EEPROM!\n");
return 0;
}
-int do_set_default(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int do_set_default(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
char *buf;
char *buf_save;
U_BOOT_CMD(
setdef, 4, 1, do_set_default,
- "setdef - write board-specific values to EEPROM (ethaddr...)\n",
- "ethaddr eth1addr serial#\n - write board-specific values to EEPROM\n"
+ "write board-specific values to EEPROM (ethaddr...)",
+ "ethaddr eth1addr serial#\n - write board-specific values to EEPROM"
);
static inline int sw_reset_pressed(void)
{
- return !(in_be32((void *)GPIO0_IR) & GPIO_VAL(CFG_GPIO_SW_RESET));
+ return !(in_be32((void *)GPIO0_IR) & GPIO_VAL(CONFIG_SYS_GPIO_SW_RESET));
}
-int do_chkreset(cmd_tbl_t* cmdtp, int flag, int argc, char* argv[])
+int do_chkreset(cmd_tbl_t* cmdtp, int flag, int argc, char * const argv[])
{
int delta;
int count = 0;
if (!sw_reset_pressed())
break;
- if ((delta > CFG_TIME_POST) && !post) {
+ if ((delta > CONFIG_SYS_TIME_POST) && !post) {
printf("\nWhen released now, POST tests will be started.");
- gpio_write_bit(CFG_GPIO_LED_GREEN, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_GREEN, 0);
post = 1;
}
- if ((delta > CFG_TIME_FACTORY_RESET) && !factory_reset) {
+ if ((delta > CONFIG_SYS_TIME_FACTORY_RESET) && !factory_reset) {
printf("\nWhen released now, factory default values"
" will be restored.");
- gpio_write_bit(CFG_GPIO_LED_RED, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_RED, 0);
factory_reset = 1;
}
printf("\nSW-Reset Button released after %d milli-seconds!\n", delta);
- if (delta > CFG_TIME_FACTORY_RESET) {
+ if (delta > CONFIG_SYS_TIME_FACTORY_RESET) {
printf("Starting factory reset value restoration...\n");
/*
return 0;
}
- if (delta > CFG_TIME_POST) {
+ if (delta > CONFIG_SYS_TIME_POST) {
printf("Starting POST configuration...\n");
/*
* Enable POST upon next bootup
*/
- out_be32((void *)CFG_POST_MAGIC, REBOOT_MAGIC);
- out_be32((void *)CFG_POST_VAL, REBOOT_DO_POST);
+ out_be32((void *)CONFIG_SYS_POST_MAGIC, REBOOT_MAGIC);
+ out_be32((void *)CONFIG_SYS_POST_VAL, REBOOT_DO_POST);
post_bootmode_init();
/*
U_BOOT_CMD (
chkreset, 1, 1, do_chkreset,
- "chkreset- Check for status of SW-reset button and act accordingly\n",
- NULL
+ "Check for status of SW-reset button and act accordingly",
+ ""
);
#if defined(CONFIG_POST)
u32 post_magic;
u32 post_val;
- post_magic = in_be32((void *)CFG_POST_MAGIC);
- post_val = in_be32((void *)CFG_POST_VAL);
+ post_magic = in_be32((void *)CONFIG_SYS_POST_MAGIC);
+ post_val = in_be32((void *)CONFIG_SYS_POST_VAL);
if ((post_magic == REBOOT_MAGIC) && (post_val == REBOOT_DO_POST))
return 1;