*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#include <version.h>
#include <asm/arch/pxa-regs.h>
-DRAM_SIZE: .long CFG_DRAM_SIZE
+DRAM_SIZE: .long CONFIG_SYS_DRAM_SIZE
/* wait for coprocessor write complete */
- .macro CPWAIT reg
- mrc p15,0,\reg,c2,c0,0
- mov \reg,\reg
- sub pc,pc,#4
- .endm
-
+.macro CPWAIT reg
+ mrc p15,0,\reg,c2,c0,0
+ mov \reg,\reg
+ sub pc,pc,#4
+.endm
+
+
+.macro wait time
+ ldr r2, =OSCR
+ mov r3, #0
+ str r3, [r2]
+0:
+ ldr r3, [r2]
+ cmp r3, \time
+ bls 0b
+.endm
/*
- * Memory setup
+ * Memory setup
*/
.globl lowlevel_init
lowlevel_init:
/* Set up GPIO pins first ----------------------------------------- */
- mov r10, lr
-
- /* GPIO41, 42, 43, 44, 45, 46, 47, 48 */
- ldr r0, =0x40E10438 @ GPIO41 FFRXD
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E1043C @ GPIO42 FFTXD
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E10440 @ GPIO43 FFCTS
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E10444 @ GPIO 44 FFDCD
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E10448 @ GPIO 45 FFDSR
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E1044C @ GPIO 46 FFRI
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E10450 @ GPIO 47 FFDTR
- ldr r1, =0x802
- str r1, [r0]
-
- ldr r0, =0x40E10454 @ GPIO 48
- ldr r1, =0x802
- str r1, [r0]
-
- /* tebrandt - ASCR, clear the RDH bit */
- ldr r0, =ASCR
- ldr r1, [r0]
- bic r1, r1, #0x80000000
- str r1, [r0]
-
+ mov r10, lr
+
+ /* Configure GPIO Pins 41 - 48 as UART1 / altern. Fkt. 2 */
+ ldr r0, =0x40E10438 @ GPIO41 FFRXD
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E1043C @ GPIO42 FFTXD
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E10440 @ GPIO43 FFCTS
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E10444 @ GPIO 44 FFDCD
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E10448 @ GPIO 45 FFDSR
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E1044C @ GPIO 46 FFRI
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E10450 @ GPIO 47 FFDTR
+ ldr r1, =0x802
+ str r1, [r0]
+
+ ldr r0, =0x40E10454 @ GPIO 48
+ ldr r1, =0x802
+ str r1, [r0]
+
+ /* tebrandt - ASCR, clear the RDH bit */
+ ldr r0, =ASCR
+ ldr r1, [r0]
+ bic r1, r1, #0x80000000
+ str r1, [r0]
+
/* ---------------------------------------------------------------- */
- /* Enable memory interface */
- /* */
- /* The sequence below is based on the recommended init steps */
+ /* Enable memory interface */
+ /* */
+ /* The sequence below is based on the recommended init steps */
/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
- /* Chapter 10. */
+ /* Chapter 10. */
/* ---------------------------------------------------------------- */
/* ---------------------------------------------------------------- */
- /* Step 1: Wait for at least 200 microsedonds to allow internal */
- /* clocks to settle. Only necessary after hard reset... */
- /* FIXME: can be optimized later */
+ /* Step 1: Wait for at least 200 microsedonds to allow internal */
+ /* clocks to settle. Only necessary after hard reset... */
+ /* FIXME: can be optimized later */
/* ---------------------------------------------------------------- */
- ldr r3, =OSCR /* reset the OS Timer Count to zero */
- mov r2, #0
- str r2, [r3]
- ldr r4, =0x300 /* really 0x2E1 is about 200usec, */
- /* so 0x300 should be plenty */
-1:
- ldr r2, [r3]
- cmp r4, r2
- bgt 1b
+ /* mk: replaced with wait macro */
+/* ldr r3, =OSCR /\* reset the OS Timer Count to zero *\/ */
+/* mov r2, #0 */
+/* str r2, [r3] */
+/* ldr r4, =0x300 /\* really 0x2E1 is about 200usec, *\/ */
+/* /\* so 0x300 should be plenty *\/ */
+/* 1: */
+/* ldr r2, [r3] */
+/* cmp r4, r2 */
+/* bgt 1b */
+ wait #0x300
mem_init:
/* configure the MEMCLKCFG register */
- ldr r1, =MEMCLKCFG
- ldr r2, =0x00010001
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
-
+ ldr r1, =MEMCLKCFG
+ ldr r2, =0x00010001
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
+
/* set CSADRCFG[0] to data flash SRAM mode */
- ldr r1, =CSADRCFG0
- ldr r2, =0x00320809
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
-
+ ldr r1, =CSADRCFG0
+ ldr r2, =0x00320809
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
+
/* set CSADRCFG[1] to data flash SRAM mode */
- ldr r1, =CSADRCFG1
- ldr r2, =0x00320809
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
-
+ ldr r1, =CSADRCFG1
+ ldr r2, =0x00320809
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
+
/* set MSC 0 register for SRAM memory */
- ldr r1, =MSC0
- ldr r2, =0x11191119
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
-
+ ldr r1, =MSC0
+ ldr r2, =0x11191119
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
+
/* set CSADRCFG[2] to data flash SRAM mode */
- ldr r1, =CSADRCFG2
- ldr r2, =0x00320809
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
-
+ ldr r1, =CSADRCFG2
+ ldr r2, =0x00320809
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
+
/* set CSADRCFG[3] to VLIO mode */
- ldr r1, =CSADRCFG3
- ldr r2, =0x0032080B
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
+ ldr r1, =CSADRCFG3
+ ldr r2, =0x0032080B
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
/* set MSC 1 register for VLIO memory */
- ldr r1, =MSC1
- ldr r2, =0x123C1119
- str r2, [r1] @ WRITE
- ldr r2, [r1] @ DELAY UNTIL WRITTEN
+ ldr r1, =MSC1
+ ldr r2, =0x123C1119
+ str r2, [r1] @ WRITE
+ ldr r2, [r1] @ DELAY UNTIL WRITTEN
#if 0
/* This does not work in Zylonite. -SC */
str r2, [r1]
ldr r2, [r1]
- /* DDR Read-Strobe Delay Calibration */
- /* bl ddr_calibration */
+ /* Hardware DDR Read-Strobe Delay Calibration */
+ ldr r0, =DDR_HCAL @ DDR_HCAL
+ ldr r1, =0x803ffc07 @ the offset is correct? -SC
+ str r1, [r0]
+ wait #5
+ ldr r1, [r0]
/* Here we assume the hardware calibration alwasy be successful. -SC */
/* Set DMCEN bit in MDCNFG Register */
orr r1, r1, #0x40000000 @ enable SDRAM for Normal Access
str r1, [r0]
+#ifndef CONFIG_SYS_SKIP_DRAM_SCRUB
/* scrub/init SDRAM if enabled/present */
- ldr r11, =0xa0000000 //RAM_BASE // base address of SDRAM
- ldr r12, =0x04000000 // size of memory to scrub
- mov r8,r12 // save DRAM size
- mov r0, #0 // scrub with 0x0000:0000
+/* ldr r11, =0xa0000000 /\* base address of SDRAM (CONFIG_SYS_DRAM_BASE) *\/ */
+/* ldr r12, =0x04000000 /\* size of memory to scrub (CONFIG_SYS_DRAM_SIZE) *\/ */
+/* mov r8,r12 /\* save DRAM size (mk: why???) *\/ */
+ ldr r8, =0xa0000000 /* base address of SDRAM (CONFIG_SYS_DRAM_BASE) */
+ ldr r9, =0x04000000 /* size of memory to scrub (CONFIG_SYS_DRAM_SIZE) */
+ mov r0, #0 /* scrub with 0x0000:0000 */
mov r1, #0
- mov r2, #0
+ mov r2, #0
mov r3, #0
- mov r4, #0
+ mov r4, #0
mov r5, #0
- mov r6, #0
+ mov r6, #0
mov r7, #0
-10: /* fastScrubLoop */
- subs r12, r12, #32 // 32 bytes/line
- stmia r11!, {r0-r7}
+10: /* fastScrubLoop */
+ subs r9, r9, #32 /* 32 bytes/line */
+ stmia r8!, {r0-r7}
beq 15f
b 10b
+#endif /* CONFIG_SYS_SKIP_DRAM_SCRUB */
15:
/* Mask all interrupts */
/* Disable software and data breakpoints */
mov r0, #0
- mcr p15,0,r0,c14,c8,0 // ibcr0
- mcr p15,0,r0,c14,c9,0 // ibcr1
- mcr p15,0,r0,c14,c4,0 // dbcon
+ mcr p15,0,r0,c14,c8,0 /* ibcr0 */
+ mcr p15,0,r0,c14,c9,0 /* ibcr1 */
+ mcr p15,0,r0,c14,c4,0 /* dbcon */
/* Enable all debug functionality */
mov r0,#0x80000000
- mcr p14,0,r0,c10,c0,0 // dcsr
+ mcr p14,0,r0,c10,c0,0 /* dcsr */
-
-
/* We are finished with Intel's memory controller initialisation */
-
/* ---------------------------------------------------------------- */
- /* End lowlevel_init */
+ /* End lowlevel_init */
/* ---------------------------------------------------------------- */
endlowlevel_init:
- mov pc, lr
+ mov pc, lr
+
+/*
+@********************************************************************************
+@ DDR calibration
+@
+@ This function is used to calibrate DQS delay lines.
+@ Monahans supports three ways to do it. One is software
+@ calibration. Two is hardware calibration. Three is hybrid
+@ calibration.
+@
+@ TBD
+@ -SC
+ddr_calibration:
+
+ @ Case 1: Write the correct delay value once
+ @ Configure DDR_SCAL Register
+ ldr r0, =DDR_SCAL @ DDR_SCAL
+q ldr r1, =0xaf2f2f2f
+ str r1, [r0]
+ ldr r1, [r0]
+*/
+/* @ Case 2: Software Calibration
+ @ Write test pattern to memory
+ ldr r5, =0x0faf0faf @ Data Pattern
+ ldr r4, =0xa0000000 @ DDR ram
+ str r5, [r4]
+
+ mov r1, =0x0 @ delay count
+ mov r6, =0x0
+ mov r7, =0x0
+ddr_loop1:
+ add r1, r1, =0x1
+ cmp r1, =0xf
+ ble end_loop
+ mov r3, r1
+ mov r0, r1, lsl #30
+ orr r3, r3, r0
+ mov r0, r1, lsl #22
+ orr r3, r3, r0
+ mov r0, r1, lsl #14
+ orr r3, r3, r0
+ orr r3, r3, =0x80000000
+ ldr r2, =DDR_SCAL
+ str r3, [r2]
+
+ ldr r2, [r4]
+ cmp r2, r5
+ bne ddr_loop1
+ mov r6, r1
+ddr_loop2:
+ add r1, r1, =0x1
+ cmp r1, =0xf
+ ble end_loop
+ mov r3, r1
+ mov r0, r1, lsl #30
+ orr r3, r3, r0
+ mov r0, r1, lsl #22
+ orr r3, r3, r0
+ mov r0, r1, lsl #14
+ orr r3, r3, r0
+ orr r3, r3, =0x80000000
+ ldr r2, =DDR_SCAL
+ str r3, [r2]
+
+ ldr r2, [r4]
+ cmp r2, r5
+ be ddr_loop2
+ mov r7, r2
+
+ add r3, r6, r7
+ lsr r3, r3, =0x1
+ mov r0, r1, lsl #30
+ orr r3, r3, r0
+ mov r0, r1, lsl #22
+ orr r3, r3, r0
+ mov r0, r1, lsl #14
+ orr r3, r3, r0
+ orr r3, r3, =0x80000000
+ ldr r2, =DDR_SCAL
+
+end_loop:
+
+ @ Case 3: Hardware Calibratoin
+ ldr r0, =DDR_HCAL @ DDR_HCAL
+ ldr r1, =0x803ffc07 @ the offset is correct? -SC
+ str r1, [r0]
+ wait #5
+ ldr r1, [r0]
+ mov pc, lr
+*/
projects / u-boot / blobdiff