endmenu
-source "cmd/fastboot/Kconfig"
-
config BUILD_BIN2C
bool
config CMD_BOOTEFI_HELLO_COMPILE
bool "Compile a standard EFI hello world binary for testing"
- depends on CMD_BOOTEFI && (ARM || X86)
+ depends on CMD_BOOTEFI && (ARM || X86 || RISCV)
default y
help
This compiles a standard EFI hello world application with U-Boot so
can be useful to see the state of driver model for debugging or
interest.
+config CMD_FASTBOOT
+ bool "fastboot - Android fastboot support"
+ depends on FASTBOOT
+ help
+ This enables the command "fastboot" which enables the Android
+ fastboot mode for the platform. Fastboot is a protocol for
+ downloading images, flashing and device control used on
+ Android devices. Fastboot requires either the network stack
+ enabled or support for acting as a USB device.
+
+ See doc/README.android-fastboot for more information.
+
config CMD_FDC
bool "fdcboot - Boot from floppy device"
help
Supports loading an FPGA device from a bitstream buffer containing
a partial bitstream.
+config CMD_FPGA_LOAD_SECURE
+ bool "fpga loads - loads secure bitstreams (Xilinx only)"
+ depends on CMD_FPGA
+ help
+ Enables the fpga loads command which is used to load secure
+ (authenticated or encrypted or both) bitstreams on to FPGA.
+
config CMD_FPGAD
bool "fpgad - dump FPGA registers"
help
help
MMC memory mapped support.
+config CMD_MMC_RPMB
+ bool "Enable support for RPMB in the mmc command"
+ depends on CMD_MMC
+ help
+ Enable the commands for reading, writing and programming the
+ key for the Replay Protection Memory Block partition in eMMC.
+
+config CMD_MMC_SWRITE
+ bool "mmc swrite"
+ depends on CMD_MMC && MMC_WRITE
+ select IMAGE_SPARSE
+ help
+ Enable support for the "mmc swrite" command to write Android sparse
+ images to eMMC.
+
config CMD_NAND
bool "nand"
default y if NAND_SUNXI
default y
depends on CMD_BOOTP
+config BOOTP_NTPSERVER
+ bool "Request & store 'ntpserverip' from BOOTP/DHCP server"
+ depends on CMD_BOOTP
+
config BOOTP_PXE
bool "Send PXE client arch to BOOTP/DHCP server"
default y
the image into RAM, then using this command to look at it or display
it.
+config CMD_BOOTCOUNT
+ bool "bootcount"
+ depends on BOOTCOUNT_LIMIT
+ help
+ Enable the bootcount command, which allows interrogation and
+ reset of the bootcounter.
+
config CMD_BSP
bool "Enable board-specific commands"
help
help
Add -v option to verify data against a hash.
+config CMD_TPM_V1
+ bool
+
+config CMD_TPM_V2
+ bool
+
config CMD_TPM
bool "Enable the 'tpm' command"
- depends on TPM
+ depends on TPM_V1 || TPM_V2
+ select CMD_TPM_V1 if TPM_V1
+ select CMD_TPM_V2 if TPM_V2
help
This provides a means to talk to a TPM from the command line. A wide
range of commands if provided - see 'tpm help' for details. The
command requires a suitable TPM on your board and the correct driver
must be enabled.
+if CMD_TPM
+
config CMD_TPM_TEST
bool "Enable the 'tpm test' command"
- depends on CMD_TPM
+ depends on TPM_V1
help
- This provides a a series of tests to confirm that the TPM is working
- correctly. The tests cover initialisation, non-volatile RAM, extend,
- global lock and checking that timing is within expectations. The
- tests pass correctly on Infineon TPMs but may need to be adjusted
+ This provides a a series of tests to confirm that the TPMv1.x is
+ working correctly. The tests cover initialisation, non-volatile RAM,
+ extend, global lock and checking that timing is within expectations.
+ The tests pass correctly on Infineon TPMs but may need to be adjusted
for other devices.
+endif
+
endmenu
menu "Firmware commands"