#include <post.h>
#include <spi.h>
#include <status_led.h>
+#include <timer.h>
#include <trace.h>
+#include <video.h>
#include <watchdog.h>
#include <asm/errno.h>
#include <asm/io.h>
# if defined(CONFIG_HW_WATCHDOG) && (defined(CONFIG_BLACKFIN) || \
defined(CONFIG_M68K) || defined(CONFIG_MICROBLAZE) || \
defined(CONFIG_SH) || defined(CONFIG_AT91SAM9_WATCHDOG) || \
+ defined(CONFIG_DESIGNWARE_WATCHDOG) || \
defined(CONFIG_IMX_WATCHDOG))
hw_watchdog_init();
-# endif
puts(" Watchdog enabled\n");
+# endif
WATCHDOG_RESET();
return 0;
text_base, bss_start, bss_end);
#endif
-#ifdef CONFIG_MODEM_SUPPORT
- debug("Modem Support enabled\n");
-#endif
#ifdef CONFIG_USE_IRQ
debug("IRQ Stack: %08lx\n", IRQ_STACK_START);
debug("FIQ Stack: %08lx\n", FIQ_STACK_START);
gd->mon_len = CONFIG_SYS_MONITOR_LEN;
#elif defined(CONFIG_NDS32)
gd->mon_len = (ulong)(&__bss_end) - (ulong)(&_start);
-#else
+#elif defined(CONFIG_SYS_MONITOR_BASE)
/* TODO: use (ulong)&__bss_end - (ulong)&__text_start; ? */
gd->mon_len = (ulong)&__bss_end - CONFIG_SYS_MONITOR_BASE;
#endif
* Record secure memory location. Need recalcuate if memory splits
* into banks, or the ram base is not zero.
*/
- gd->secure_ram = gd->ram_size;
+ gd->arch.secure_ram = gd->ram_size;
#endif
/*
* Subtract specified amount of memory to hide so that it won't
gd->arch.tlb_addr = gd->relocaddr;
debug("TLB table from %08lx to %08lx\n", gd->arch.tlb_addr,
gd->arch.tlb_addr + gd->arch.tlb_size);
+
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+ /*
+ * Record allocated tlb_addr in case gd->tlb_addr to be overwritten
+ * with location within secure ram.
+ */
+ gd->arch.tlb_allocated = gd->arch.tlb_addr;
+#endif
+
return 0;
}
#endif
-#ifdef CONFIG_LCD
+#ifdef CONFIG_DM_VIDEO
+static int reserve_video(void)
+{
+ ulong addr;
+ int ret;
+
+ addr = gd->relocaddr;
+ ret = video_reserve(&addr);
+ if (ret)
+ return ret;
+ gd->relocaddr = addr;
+
+ return 0;
+}
+#else
+
+# ifdef CONFIG_LCD
static int reserve_lcd(void)
{
-#ifdef CONFIG_FB_ADDR
+# ifdef CONFIG_FB_ADDR
gd->fb_base = CONFIG_FB_ADDR;
-#else
+# else
/* reserve memory for LCD display (always full pages) */
gd->relocaddr = lcd_setmem(gd->relocaddr);
gd->fb_base = gd->relocaddr;
-#endif /* CONFIG_FB_ADDR */
+# endif /* CONFIG_FB_ADDR */
+
return 0;
}
-#endif /* CONFIG_LCD */
+# endif /* CONFIG_LCD */
-#if defined(CONFIG_VIDEO) && (!defined(CONFIG_PPC) || defined(CONFIG_8xx)) && \
+# if defined(CONFIG_VIDEO) && (!defined(CONFIG_PPC) || defined(CONFIG_8xx)) && \
!defined(CONFIG_ARM) && !defined(CONFIG_X86) && \
!defined(CONFIG_BLACKFIN) && !defined(CONFIG_M68K)
static int reserve_legacy_video(void)
return 0;
}
-#endif
+# endif
+#endif /* !CONFIG_DM_VIDEO */
static int reserve_trace(void)
{
if (ret)
return ret;
#endif
+#ifdef CONFIG_TIMER_EARLY
+ ret = dm_timer_init();
+ if (ret)
+ return ret;
+#endif
return 0;
}
defined(CONFIG_ARM)
reserve_mmu,
#endif
-#ifdef CONFIG_LCD
+#ifdef CONFIG_DM_VIDEO
+ reserve_video,
+#else
+# ifdef CONFIG_LCD
reserve_lcd,
-#endif
+# endif
/* TODO: Why the dependency on CONFIG_8xx? */
-#if defined(CONFIG_VIDEO) && (!defined(CONFIG_PPC) || defined(CONFIG_8xx)) && \
+# if defined(CONFIG_VIDEO) && (!defined(CONFIG_PPC) || defined(CONFIG_8xx)) && \
!defined(CONFIG_ARM) && !defined(CONFIG_X86) && \
!defined(CONFIG_BLACKFIN) && !defined(CONFIG_M68K)
- reserve_video,
-#endif
+ reserve_legacy_video,
+# endif
+#endif /* CONFIG_DM_VIDEO */
reserve_trace,
#if !defined(CONFIG_BLACKFIN)
reserve_uboot,
if (initcall_run_list(init_sequence_f_r))
hang();
+ /*
+ * The pre-relocation drivers may be using memory that has now gone
+ * away. Mark serial as unavailable - this will fall back to the debug
+ * UART if available.
+ */
+ gd->flags &= ~GD_FLG_SERIAL_READY;
+
/*
* U-Boot has been copied into SDRAM, the BSS has been cleared etc.
* Transfer execution from Flash to RAM by calculating the address